Paul Horton's Welder Series
3.99K
  • Popular uploads Play all

    • Chevy Motor Mounts - Duration: 9 minutes, 2 seconds.

      • 10 years ago
      • 115,161 views
      This is our #C005 universal Chevy motor mount kit. It is designed to hold the engine the way GM intended - not relying on the shear strength of the bolts going through the mounting tabs. It's easy ...
    • Bars - Duration: 5 minutes, 56 seconds.

      • 12 years ago
      • 56,720 views
      Welder Series assembly video for bars. Multiple uses - four bar kits, panhard bars, etc.
      welderseries.com
    • Updated Mustang II Assembly - Duration: 5 minutes, 13 seconds.

      • 9 years ago
      • 44,906 views
      I've revised my technique from the last video, and thought I'd show you how to assemble our Mustang II crossmember a bit faster. http://www.welderseries.com/blog/online-store/ws14540/
    • New Universal Sway Bar Kit - Duration: 3 minutes, 34 seconds.

      • 10 years ago
      • 41,459 views
      We've made a slight change to our sway bar kit to make it even more universal!
    • tig welding behind the mask - Duration: 68 seconds.

      • 12 years ago
      • 39,363 views
      here's a (rather poor quality) example of tig welding pulses and puddles.
    • Mustang II kit complete - Duration: 8 minutes, 51 seconds.

      • 11 years ago
      • 37,955 views
      Here I assemble a Welder Series Mustang II kit. Ready to weld in about five minutes!
    • Welding With DW: how I hold the filler - Duration: 3 minutes, 16 seconds.

      • 9 years ago
      • 36,733 views
      Here are a few tips on advancing and holding the filler rod.
    • Triangulated Four Link Upper Bar Placement - Duration: 78 seconds.

      • 2 years ago
      • 36,215 views
      I've got the upper bar brackets ready to tack in place. Here are a few things to keep in mind...
    • Chevy small & big block motor mounts - Duration: 6 minutes, 27 seconds.

      • 11 years ago
      • 35,153 views
      In this video, I weld one of our small block Chev motor mounts.
      Note: this kit has been replaced by #215900.
    • Model A rear crossmember - Duration: 69 seconds.

      • 11 years ago
      • 30,622 views
      Rear crossmember kit for a Model A. #WS00013N
    • Optrel Panoramaxx Unboxing & First Weld - Duration: 22 minutes.

      • 2 years ago
      • 29,815 views
      I bought a brand new welding helmet! If you have any questions about it, please leave a comment.
    • rear four link frame bracket - Duration: 6 minutes, 41 seconds.

      • 11 years ago
      • 29,160 views
      This is a companion video to the rear four link axle bracket... universal mount.
    This item has been hidden
  • Uploads Play all

    • Behind The Lens: Optrel Panoramaxx - Duration: 40 seconds.

      • 9 months ago
      • 1,250 views
      Join me! This is a pretty accurate color depiction of the arc.

      P.S. Honestly, I didn't record in portrait.
    • Tuning Your New Tig Gloves - Duration: 56 seconds.

      • 11 months ago
      • 523 views
      You don't have to use floppy fingered gloves... I'll show you how to snug them up to give you a nicer, custom fit.
    • Flowmaster HP-2 mufflers on a Mopar 318 - Duration: 33 seconds.

      • 1 year ago
      • 2,491 views
      After we loosely dialed the timing in, this is one of the first few starts... it still needs a bit of tuning.
      Edelbrock 600cfm carb, Edelbrock intake, Gibson headers, Flowmaster 2.5" dual exhaust w...
    • D100: Installing new door hinge pins - Duration: 7 minutes, 54 seconds.

      • 1 year ago
      • 520 views
      Replacing the tired, worn out hinge pins with brand new pins and brass bushings. The job was a bit more involved than I first thought...
    • Welder Series Sway Bar Tip: keep your arm on! - Duration: 116 seconds.

      • 1 year ago
      • 1,185 views
      Even though the splined end of our universal trim-to-fit sway bar kit has a set screw, the arm can sometimes work its way off the bar. I've got over 40,000 miles on the '32 without any movement by ...
    • D100 Mustang II Installation, Video 4: Upper Towers - Duration: 12 minutes.

      • 1 year ago
      • 3,311 views
      Opening screen is supposed to say:
      1968 Dodge D100
      Mustang II Install
      Video 4: Upper Towers and Shockwave mounting plates :)

      Trimming the control arm upper towers and Shockwave mounting plates usi...
    • How To Crimp EZ Clip Hoses - Duration: 8 minutes, 14 seconds.

      • 1 year ago
      • 2,739 views
      I'll never use another hose system again after I built the '32 back in 2006 or so. This kit from Vintage Air is the easiest, most flexible way to route your air conditioner hoses.
    • TIG Welding a Model A Rear Crossmember - Duration: 7 minutes, 18 seconds.

      • 1 year ago
      • 698 views
      TIG welding our #00013N crossmember. Skip to 6:55 for the results.
    • Huge Deuce Burnouts - Duration: 79 seconds.

      • 1 year ago
      • 581 views
      Danny's 32 Ford has a chassis I built with Welder Series parts in our pre Welder Series days. When I asked Danny if I could post the videos he sent me, he called back and left the message that you ...
    • D100 Rear Sway Bar, Part 1 - Duration: 11 minutes.

      • 2 years ago
      • 2,385 views
      There's not much Sweptline-specific content in this video, but I used our trim-to-fit sway bar kit on my D100 project, so it fits in to the playlist :).
    • Welder Series Step Notch on the Sweptline - Duration: 12 minutes.

      • 2 years ago
      • 1,898 views
      My friend David Bailey is the guest editor on this video... thanks for your help David! Here's a link to his channel: https://www.youtube.com/channel/UCAacyJ21pnu-l-AdrWceEmw
    • Optrel Panoramaxx Unboxing & First Weld - Duration: 22 minutes.

      • 2 years ago
      • 29,815 views
      I bought a brand new welding helmet! If you have any questions about it, please leave a comment.
    This item has been hidden
  • Welding With DW: Over My Figurative Shoulder Play all

    This item has been hidden
to add this to Watch Later

Add to

Loading playlists...