456
  • Euro CanTech 2018 Milan - Duration: 3 minutes, 31 seconds.

    • 4 months ago
    • 229 views
    Description
  • Pride Engineering - Duration: 98 seconds.

    • 1 year ago
    • 349 views
  • Pride Wide - Duration: 95 seconds.

    • 1 year ago
    • 89 views
    Description
  • CMB - 1000th Bodymaker - Duration: 4 minutes, 54 seconds.

    • 1 year ago
    • 2,458 views
  • CMB - Duration: 5 minutes, 21 seconds.

    • 2 years ago
    • 229 views
  • Open Up to Cans - Duration: 2 minutes, 9 seconds.

    • 2 years ago
    • 695 views
  • Rexam's 2015 Sustainability Report - Duration: 6 minutes, 8 seconds.

    • 3 years ago
    • 449 views
    John Revess, director of sustainability at Rexam and Richard Piper, editor of CanTech International discuss Rexam's 2015 Sustainability Report.
  • The Rexam Design Centre - Duration: 91 seconds.

    • 3 years ago
    • 733 views
  • Stolle Saber Trimmer - Duration: 98 seconds.

    • 3 years ago
    • 2,312 views
  • A typical three-piece canbody production line - Duration: 6 minutes, 12 seconds.

    • 5 years ago
    • 9,753 views
    A typical canbody production system consists of a slitter (to cut the tinplate base material into body blanks of the required size), a transfer system (to feed the cut blanks from the slitters to t...
  • Part 5: Outside coating - Duration: 17 seconds.

    • 6 years ago
    • 10,837 views
    Two-piece can making process: Outside coating

    The cans are coated on the outside as protection against corrosion and in order to apply a decorative design. White, gold or transparent coating as we...
  • Part 1: Blanking and deep drawing - Duration: 23 seconds.

    • 6 years ago
    • 54,045 views
    Two-piece can making process: Blanking and deep drawing

    The tinplate strip is unwound, its surface coated with a thin film of lubricant and the strip continuously conveyed to the deep-drawing pres...
  • Part 2: Wall ironing and end forming - Duration: 46 seconds.

    • 6 years ago
    • 34,620 views
    Two-piece can making process: Wall ironing and end forming

    The cup is conveyed to the wall-ironing machine from the top. The ram first pushes it through the redraw ring to reduce its diameter to t...
  • Part 4: Washing - Duration: 28 seconds.

    • 6 years ago
    • 12,154 views
    Two-piece can making process: Washing

    The wall-ironing lubricant used in the can forming process is removed prior to coating the can internally and externally. The cans are transported to the wash...
  • Part 3: Trimming - Duration: 12 seconds.

    • 6 years ago
    • 14,567 views
    Two-piece can making process: Trimming

    In the trimming machine the can is held by a vacuum plate, set in rotation and then moved axially until it reaches the required trimming height. Then the mov...
  • Part 14: Palletizing - Duration: 66 seconds.

    • 6 years ago
    • 2,462 views
    Two-piece can making process: Palletizing

    The palletizing unit assembles the cans in up to 23 layers to a package unit almost three metres high. The palletizing process starts by picking up an emp...
  • Part 13: Testing for internal defects - Duration: 50 seconds.

    • 6 years ago
    • 2,458 views
    Two-piece can making process: Testing for internal defects

    This test is a continuous 100% test of the inside of the can. It is performed by a CCD line scan camera system comprising five cameras.Ca...
  • Part 12: Testing for holes and flange cracks - Duration: 20 seconds.

    • 6 years ago
    • 1,812 views
    Two-piece can making process: Testing for holes and flange cracks

    These two types of defect can occur due to the great degree to which the tin plate is formed. Each can is picked up by a support s...
  • Part 11: End coating - Duration: 44 seconds.

    • 6 years ago
    • 2,364 views
    Two-piece can making process: End coating

    The metallic bright can end is coated from the outside in the end coating machine. The cans are conveyed via the intake turret to the working turret. Each...
  • Part 10: Flanging - Duration: 15 seconds.

    • 6 years ago
    • 5,974 views
    Two-piece can making process: Flanging

    The flange is required in order to seal the filled can securely to the end. The flange is produced in the 16th station of the necking in and flanging unit.

    ...
  • Part 9: Necking - Duration: 31 seconds.

    • 6 years ago
    • 4,832 views
    Two-piece can making process: Necking

    The diameter of the can which is still cylindrical needs to be reduced in the upper section to accommodate the smaller end. During the necking process the can...
  • Part 8: Initial internal coating - Duration: 29 seconds.

    • 6 years ago
    • 2,906 views
    Two-piece can making process: Initial internal coating

    Inside the internal coating machine, the can is conveyed to a coating turret and positioned on a vacuum plate. It is set into rotation and pa...
  • Part 7: Drying - Duration: 47 seconds.

    • 6 years ago
    • 2,129 views
    Two-piece can making process: Drying

    The drying oven is basically divided into three zones (two heating zones and one cooling zone). The heating zones serve to heat the cans and to evaporate the f...
  • Part 6: Printing - Duration: 29 seconds.

    • 6 years ago
    • 2,404 views
    Two-piece can making process: Printing

    The externally coated cans are spaced by the intake wheel, as in the coating machine, and drawn on to the mandrel wheel mandrels by means of a vacuum. The ma...
to add this to Watch Later

Add to

Loading playlists...