2.73K
  • Water Bike 'Liquid Nails' 3 - Duration: 2 minutes, 11 seconds.

    • 9 months ago
    • 714 views
    My Latest design, with 3D Printed PLA Gearbox. Will it work ?
  • Surface mount components with hand tools - Duration: 13 minutes.

    • 10 months ago
    • 274 views
    Soldering surface mount components with good old hand tools.
  • Solder Dip Robot - Duration: 112 seconds.

    • 1 year ago
    • 583 views
    DIY Solder Dip Robot, First test.
    This is designed to give consistent results using a Solder Pot for through-hole circuit board assembly. Alternative to hand soldering or manual dipping.
  • 'Liquid Nails 2' Pedal Boat - Duration: 2 minutes.

    • 1 year ago
    • 365 views
    Pedal Boat using gearbox from an Angle Grinder. It's not electronic, but it is fun.
  • GT2 Timing Belt Joining - Duration: 3 minutes, 20 seconds.

    • 2 years ago
    • 26,994 views
    DIY timing belt join.
  • Printed Circuit Board Design : Beginner. Step by step - Duration: 26 minutes.

    • 2 years ago
    • 182,103 views
    Too Easy guide: Using Diptrace to draw a schematic and design a PCB
  • Raspberry Pi: Control 100 Relays Python example - Duration: 12 minutes.

    • 2 years ago
    • 31,989 views
    Controlling 100 relays using serial-interface relay modules linked in a daisy chain.

    Python Code: http://www.tctec.net/super8.py

    Want to know where you can get a Super8 relay board ?
    Ask 'little...
  • 3D Printed Perestaltic Pump Parts - Duration: 96 seconds.

    • 2 years ago
    • 5,189 views
    This is a working prototype made from readily available components and a 3D printer (PLA). How does it work ?: An arm turns and squashes a silicone hose, as the Hose is squashed, liquid is pushed o...
  • Arduino Popcorn popper - Duration: 2 minutes, 22 seconds.

    • 3 years ago
    • 465 views
    Making popcorn with low-watts is a difficult challenge. However, the reward is a crispy perfectly-popped Kernel of Popcorn.
    With a 3D printer and no life responsibilities; Anything is possible !
  • Hexapod Robot by Surfdabbler - Duration: 58 seconds.

    • 3 years ago
    • 203 views
    Beautiful Hexapod built from flat acrylic cutouts. Each leg controlled by servos. PIC32 based control board. Designed and built by Surfdabbler.
  • Power Button with Kodi - Duration: 115 seconds.

    • 3 years ago
    • 1,933 views
    On/Off power button with Kodi on Raspberry Pi

    Schematic:

    http://www.tctec.net/RPI_Power_Button.pdf
  • Raspberry Pi: On Off Power Button - Duration: 3 minutes, 45 seconds.

    • 3 years ago
    • 38,153 views
    Schematic Below !
    If it's useful give the clip a 'Like' !
    Power-On , Power-Off using Momentary Push button

    Schematic:
    http://www.tctec.net/RPI_Power_Button.pdf

    Python Script:
    http://www.tctec.net...
  • Raspberry PI, C++ programming with Visual Studio and VisualGDB ! - Duration: 9 minutes, 5 seconds.

    • 4 years ago
    • 87,032 views
    Using Visual Studios' slick IDE for Raspberry PI C++ programming. Needed to buy 'VisualGDB' plugin, but well worth it.

    We have been using this setup successfully for fairly large C++ applications...
  • ModDrive 2 Electric Boat Controller - Duration: 95 seconds.

    • 5 years ago
    • 5,215 views
    Here is the first production PCB of our motor controller.
    Mod Drive-2 is a 4kWatt Brushless-DC (BLDC) Motor controller, featuring one button control.
    Designed for reliability. (Because it's running...
  • Electric Inboard DIY : First Water Test - Duration: 82 seconds.

    • 5 years ago
    • 6,059 views
    First water test. Running at 12 Volts (1 quarter power ). No water cooling. Small trip, 10 minutes running time. This is the only footage.
  • Electric Boat Inboard DIY - Duration: 27 seconds.

    • 5 years ago
    • 45,796 views
    Running at 36V near top speed.
    Seems like plenty of thrust and too much speed.
    May be better to run at 24V with this prop.
  • TM220A TM240A Adjust Speed to improve Accuracy - Duration: 66 seconds.

    • 5 years ago
    • 760 views
    Improve accuracy by adjusting speed within the pick and place file.
    (Just discovered this by reading page 10 of the manual)
  • TM220A placing components - Duration: 26 seconds.

    • 6 years ago
    • 339 views
    TM220A placing components, including front tray pick up.
to add this to Watch Later

Add to

Loading playlists...