 Okay, so we're on call Saturday. We've got a milkshake machine. It's not working So let's go in here and see what's going on. Supposedly they cleaned it and Ice cream mix came all off the back of the machine. Then it miraculously just quit working Okay, let's take a peeky-poo here Those cleanser gonna get it. All right See what we got going on. Let's get this thing yanked out of here so we can get Get it figured out what's going on This should be really good All right, well, I just changed this motor A few days ago back on the first day is the 23rd. See how all the crap comes down through here It comes down to here and gets into all this Changes back in the 20th See that would have just set in there. I think what I'm gonna do is I'm gonna drill a hole in the bottom of this It leaks on out that way and this kind of crap happens again. It'll Be okay. I Think I used silicone this time to help protect it to keep the crap out. It looks like it kind of did the job Which is good Might be better off just take this thing out the back door and just wash it out with a friggin garden hose It's really sweet Really sweet See our capacitors luck well if you got stuff in the capacitor there on top Then it means it must have got down the wine Looks like it's in there We're taking a look at the rear here Get your seal which supposed to be put on dry than lubricated When you decide to leave it ahead of time and slide it on there You end up having it spin on the back and it ends up eating up the shaft So you can see where it's stuck down in there and then this here I mean, it's just probably got a lot of age on it But you can see the deep deep groove there and so you're gonna have a space Between this which goes at the back of the machine and then this here comes to the front Pivots on that piece right there It's like that in the machine for it to gotten that much through there Something's not right how that would have just all sudden gave out it was working before they cleaned it It just seems to be very suspicious I'm gonna guess that something probably didn't get put into place right, but we definitely got this Needs replaced right away. This Probably could TIG weld that on there and then turn it on a lathe and grind it back down but See that or spin probably 800 to $1,000 on one of those I bet you I'm not sure but it definitely is warrior So let's get it together and see what happens here So it drilled a few holes in here Makes it a little easier to Get some that crap out of there I wouldn't hurt to have a little something up here in that But they're not gonna work So I've got it in there. They say they sanitized it before doing this which is supposed to sanitize right before you turn it on Which makes no sense how that wouldn't have leaked out. So we're gonna go ahead and run some sanitizer through it first Got that bit off to the side So let's go ahead and see if we can get that in there That's your drain pan here. This has been the first indication that it was coming out that's it's Not it's it's all the way to the back See that That's full of gunk But I think I should do is honestly break that or drill it so that comes flying off the front because It's pretty much worthless the way it is right now It would be better that drained out the front than to have it drain all Inside the machine Be honest with you. You got that drilled right there Give them a little bit of a lap But the most part it's gonna drain out the front now Maybe somebody will catch this way before this starts going into a disaster Let's go ahead and get the sanitizer in there and see how it does Some sanitiser here, we're gonna put this in with this cold water. You're not supposed to use hot water Hot water does a nicer job, but on some machines you can take a chance of blowing the Barrel out on them because it causes to expand and some of them have solenoids before and after the barrel and I can cause some Undesirables there So we've got Milk got the sanitizer in there Don't see anything coming out of the back of the machine, which is kind of interesting since It didn't happen when they first did it little little odd They said I wouldn't do anything either. It's running in clean mode The wiper blades there they're beyond need and replaced. I've mentioned that before but they didn't get them replaced A lot of times I get their own parts not much I can do about that Let me get down and make sure they stayed in position there. It's it's a Less than desirable type of blade usually you've got nice wiping blades. Just keep going. This is the same model We're pretty much just like the same model that just replaced the compressor on in another video that I did a while back Still nothing coming through there. Let's go ahead and give this about five minutes and Don't doubt we'll throw some mix in there and see if it makes a milkshake Just get in there with the Go to a brag and get this all cleaned up so That you would even want to get a milkshake out of it. I'd like to see my machines Nice and clean That way even I would want to eat out of it make darn sure You don't have a bunch of build up here like they've got that'll cause false alarms makes you think it's full of mix when it's not And everything's working just like it should right now. I'm not real sure why this catastrophe here happened Everything's in correct order right this kind of peculiar But it's a mess to dump the whole barrel before you was able to dump it out like I'm doing right now Because if you had a catastrophic failure seal failure You should be able to drain it out pretty quick because it's not for us down I've seen some really big dents. There's a stainless steel pin here that goes in there to the safety switch Which actually goes up here, but seemed a huge dent down here on the bottom Then they tightened it down tight enough to actually penetrate into the stainless steel and really Put a dent in it so yeah Things happen for sure Stop that Go ahead and turn power off Let's take a look at those wipers and make sure they're still in place I don't want to dump all that mix in here and then find out that it's not in place So let's go ahead and get that out of there You can see the wiper blade right there a little flat thing. You see the other one right there It's in position still so we're good there and as you can see there's that one there Let's go ahead and get this back together now When the person was showing me how they put it together this talk that this might have went on the back and that very very very likely is what happened But now nobody wants to admit that That feels like The lubricant on the front which should not be on there Also, you would figure if they had it all the way forward Not that piece there it would have ate into it a little bit But it doesn't look like it did Okay, so When I just washed it out or washed it out depending on what you got going on And just flipped her sideways like that And just let her drain out. I'm gonna go grab my blower and blow everything off capacitors Or anything it got wet That's careful around that high pressure switch down there and it's pretty much in case anyhow other than that We should be able to get it back in there. They're cleaning up the other mess Didn't think I was gonna have to bring it out here But evidently wasn't a whole lot of options and as bad as that was it was gonna stink high heck and back I don't care to deal with that later. You'll have to chisel it out And it's just that's just horrible stuff to deal with once it's hardened and it was getting pretty bad there We got all the capacitors dried out the tops of them this one here. It's got the white crap all over it That's hard. It won't come off. It's been there for a while. It's above the actual letroids or what have you? it It's good as that's gonna be Got the limit blown out just in case motors wiped off and good got the tray all that was all taken care of so Let's put it back together Like I said if thin water does not leak out the front then the mix should not leak out the front What I think happened was they put the white Bushing that's on the front I think they put that on the back for whatever known reason and because it has a nub on the front It would have still set in there and would have rotated without any major noise because when they were showing me how they put it together They said it goes on the back, right? I'm like, uh, no. Oh, yeah. Yeah, I put it on the front I think that's what actually happened problem is is training training training training training They really need a video and I've offered to make a video for them if they would just give me a place to upload it Well, so I'm here on Saturday. Anyhow Let's go ahead and get this thing back together should work just fine I haven't tried the compressor yet. I hope hope it works We may kick out on first just to make certain before I waste my time putting mix in there If you're wondering, this is a water cooled machine the water Comes in through the hose right there into the back of the machine and then comes out on another hose back into There and now the drain Use a little bit of water. This is got a coax coil right there That's how that system works at your condenser there water cool condenser. Let's go ahead and plug it in and see what happens Everything looks like it's probably fine Let's see what goes. We got a plug in Let's go ahead and see what happens snot There we go clean works Things stops. Let's go to freeze freeze will not probably run unless we've got something in there the last time It kicked on since I did that Okay, we've got something in there. Let's see this thing will freeze Well, it's not enough Yeah, still not enough gotta get a little more. I gotta get that carburetor in there, too We have a problem here. We've got one blank on the clean light I was hoping that was just sitting there and stand by This board's a little bit of a pain to butt. You have to look it up. If it ends. It's dead like that It's not a good sign Yep, the power's on power board's there Might have finally lost the board Oh, look at that. It just came on. That's kind of interesting, wasn't it? Huh, we're not blinking no more low mix. Let's uh I don't like seeing the amperage there change like it's doing. It's a little screw ball See if we can push the freeze Look at that Impressor came on Look at that all the mix ain't coming out the front kind of around to the ceiling Didn't do anything different than put the machine together correctly That'd be interesting So hopefully this thing will freeze down and we can get out of here See what happens here. Let's give it a moment. Let's kind of go get a little more mix A little bit low yet. The machine completely shut off I'm thinking we might have drawn a blown a break or some sort Which kind of stinks It was doing so good for a while there. Hmm. All right, let's go check the brake pads I don't see nothing there Let's see one. It's off 38. It looks like spare That one's all looks to be on We do have 230 volts there, but you know what I think I did. I think I forgot to turn the water back on Let's go ahead and get that real quick. Oh my I made a mistake. Holy crap Get ahold of the vacuum, please. Maybe they can write the ticket Okay, well the water came through really quickly Let's go ahead and hit the reset button because I got shocked the last time I touched it Finish the freeze compressor came on Let's see if it makes a milkshake this time So far so good Okay, you can't charge by this cycle or that cyclist But at least gives you an indication how things are working. It's green and it's solid So we're good there on that. It's running here. It's coming out, you know medium warm maybe 80 degrees 90 degrees, I don't know. It's don't feel real hot but it's definitely freezing down It's cycled off twice. I pushed the freeze twice. This should be ready to go. Let's grab a cup Right to me Look at that. It's like a milkshake All right, I would say they probably didn't put it together correctly And that would just lead the technician in the wrong direction. I think there's something majored on wrong besides the seals that are wore out and could waste a lot of time Something corny was going on with the board, but that sometimes happens. I think I'm jumping to conclusions on that I'm going to say it's ready to roll They're busy. Let's go ahead and ramp this one up. Well guys today. It's 86 according to my van I would say it was supposed to be 80. I don't know if it's really that warm or not, but That's what we end up having. I truly believe they put the machine together incorrectly because they showed me the Incorrect way then once I said that wasn't correct and they ended up saying that wasn't how they did it Either way, it really doesn't matter who's fault it is But they really need to have some picture pages there so they can just flip through it and how to put it together I've showed several different employees how to do it and the problem is the high turnover in the restaurant industry That person's lucky if they last a few weeks and then someone else is in that place Then, you know, it just happens from there. It's done. It's working. The guys enjoyed the video and you want to see more like it As always Don't subscribe. Don't click that thumbs button. Don't check out facebook and don't check me out on instagram And until next time guys, we will catch you on the next one We won't catch you on the next one later