 All right, let's see if we can get the pressure washer fixed Got a part in today Let's give it a shot Okay, guys, so The other day we were working on this the rope kept pulling, you know, it wouldn't started rope would yank out of your hand and We took the valve cover off looks like it's bent right here Down there on the bottom not positive, but it sure looks like it to find that So my guess is That that's going to be an issue the issue of why That thing wouldn't wouldn't start and it kept yanking the pull rope Out of our hand So we've got the genuine Honda part right here Again, this is not mine guys. It's for a friend of mine. He does a lot of things for me. He's always given me something so After I finished the video Monkey said how much are them things I said they're not very much She said you know what once you go ahead and order him one and put that in there and see if that's a problem So I was like, you know, all right, I will so I looked it up and I Got the part you can see it's not used genuine Honda part six dollars forty three cents What that cost me and it was shipped here It wasn't supposed to be here till the 29th and then I got a notification saying that it was going to be here the 24th, which is Christmas Eve Then I got a notification today saying it's out for delivery. So These two things up here. Yeah, you can see But that is way off so hopefully that is the problem We got to put this over here on this side and we have to adjust it Well, this feeler gauge. Well, you know, I'll adjust both of them if I can read this again anymore This this was her dad's It's an old one The intake and you can always tell the intake exhaust the intake is always closest to the To the carburetor and exhaust is always well close to the exhaust the muffler the intake should be six thousandths and The exhaust I believe is eight thousandths So I've got to see if I can read these numbers All right, so Like seven looks like Maybe eight there. I really need to get another set of these Can't read them. That looks like nine Eight nine ten All right, so Stuck these back on there, you know, so it wouldn't get moisture. I Got to straighten this up a little bit. It did get a little bent trying to take it off And I got to see if I got any I'm down underneath here It's if I got any Gasket sealer gasket maker stuff. That's what you use on these things. We've got to get it cleaned up real good So let me go ahead and get that taken care of I'm gonna pull this off. We'll get this cleaned off straight now We'll put this on which is only That's the only thing that holds it on that right there had a little pin That's the only thing it holds it on I don't feel any I mean you can see where it was riding, but I don't feel any debit. So this should be fine And again, there's our cracked one so You can Tell a difference Had a guy comment on that. I know he didn't watch the whole video Because he commented turn the fuel valve on And check valve Valve lash well first of all turning your your fuel on has nothing to do with your valve lash Here's where you check your valve lash, here's where you adjust your valves right here So if I pulled this off apparently I had found a problem. So I know he didn't watch the whole video so anyway, I Just commented, you know if you watched the whole video you probably wouldn't have Posted that comment, but you know, I don't understand Why people won't watch the whole video and then you know, then they can't take it back. It's like well You know go back and watch the video. You'll see I took this off. There's there was no sense in checking the valve the valve lash Because right right there's the problem, you know, I mean so why check it? It's not gonna be right. I know that Okay, guys Let me get this off of here and get it straightened out getting closer. Okay guys, I pulled the exhaust the heat shield off I'm gonna clean that up a little bit for For Ryan. It was funny because the other day I had that Had this old part in that plastic bag the day I made the video and I had it sitting right up here Hey stop by that was funny. We just Monkey was having a sale yard sale. So we just came out and From ordering that part and he showed up And he asked he said What do you think about this thing? I said I haven't had a chance to look at it yet And I looked down and there was that partly and right there in that plastic bag. I was like, oh man because I'm trying to surprise him, you know and And That's like on it. He didn't see it or if he did he didn't say anything So I'm gonna go ahead and run this on the buffer real quick clean it up some okay guys, so Had to go get some of this gasket making stuff Just put it on You let it dry until it gets tacky I know a lot of people say oh you should use the black RTV and you know that stuff's like 17 dollars I ain't Like Terrell says this it's not the space shuttle. It's a small engine The stuff will work. It doesn't have to hold anything tight. It just keeps it from leaking. That's all So I'll let it get tacky and I'll put it on then I'll start the boats and I'll let it set for a couple more minutes Then Then we'll tighten her up So before I do too much cleaning On this thing. I want to make sure that's gonna be the only issue it has And also that the black stuff you got to wait 24 hours on it And I've never done that I waited till got tacky put it on bolted up by the time I got everything together it was ready, and I've never had an issue with it All right, let's let that get tacky Then we'll put that on I'll check the oil again because I know I lost a little oil so We'll top the oil off and then if it runs good We'll go ahead and clean the rest of it up with WD 40 or something like that. Okay guys, so I didn't Turn you on when I stuck that back on but I was talking to you Don't suck it Okay So I did I let this set up for about a half an hour 45 minutes I want to tighten them up a little bit They don't have to be super duper tight Just keeping out oil Shame I can't get to those with my little gun here again not tight just snug them up Now I'm gonna set let it set up a little bit longer Then we'll take it over and see if it'll fire up and if it does Then we'll finish I was doing some wiping Wiping it down a little bit and Yeah, just and I clean the some of the grime off of it And if it runs good Then we'll go ahead and wipe off the rest of it Make it look halfway decent for him All right guys. Yeah, I see so Yeah, that's what we're gonna do Let's let it set for a little bit longer And hopefully it'll fire up for us. We'll take it over hook it up to the water and check it out. Okay guys I'm going with one pool. We'll give it a second for the fuel To get where it's got to go and if it runs, we'll clean it up. I'll give him a call Let him come down and pick it up All right, let's try it one pull. Well, it started one pull That was good. All right Now I figured that was gonna start with one pull because These Hondas normally do there's no primer on them. You choke them They start like, you know, it's like a car with an automatic choke, you know You just get in starting. So I figured it would but there's always that possibility But I did When it was up on the table, I did pull a couple times to make sure that it wasn't, you know, feeling like it was locking up And that probably helped prime it. So, you know, but so I figured now I do have a wand that'll fit on there But my wand's only rated at a thousand psi and this is three thousand. I think Yeah, this is three thousand. So it probably blown my hose up, but you can see it's working So I'm gonna shut the water down Well, I'm gonna let it run for a few minutes, then I'll shut the water down I'll get you back up on the table and let's clean it up for him and I'll give him a call Okay, guys, I showed this a while back on how you can clean up plastic with transmission fluid And if you look at that real close You're like that. Look at that. See the difference and wipe off the excess and there you go A lot of people think dirt would stick to it, which yeah, you would think that Let's check this out down here, but actually Dirt kind of rolls off of it Now what we used to use on our four-wheelers and stuff on the plastics of our four-wheelers. We used to use WD-40, but I'm getting kind of low on my WD-40. So I'm gonna use transmission fluid and look at that And it'll stay that way some of the stuff you put on there, you know how like oh I don't know what it's called the stuff you use on your dash and stuff those wipes It dries up. It will dry out after a while. It looks the same. So Let's get a before this There's before and there's after guys. So Yeah, it really cleans up nice when you do that. Yeah Even cleaned that up a little bit So there you go She's running. I'm gonna give him a call having come pick it up and I'm gonna say shea bear the myth man a legend I'm gone for now and Weekends coming up so Well, you'll see this on the weekend. So have a great weekend and a merry Christmas Christmas Eve is Saturday So I'll probably be doing a live stream I don't know how long I'll go for but I'll do a live stream of the lights like I did last year play some music Go from there. All right guys again. Thanks for watching. I appreciate it and Stay tuned for more videos. We'll see you in the next one guys. Bye. Bye and take care