 All right. Oh look at that. Okay, that's where my lumber mill goes right there. Oh nice work That was two days of digging more or less Yeah, that's about perfect. I think I'll put little concrete circles kind of like You know railway ties Under these first I'll get the lumber mill up here though. So I make sure I get them positions just right I guess I better go make some wheels That's the canoe that I made years ago. I put an outrigger on it and my friend there put a four horsepower motor on it and that thing will go like 10 to 15 miles on a gallon of gas. It's just pretty good in a boat Okay, wheels right the bottom of this thing. Oh It's gonna be so nice to get that out of here and Some of the stuff put away All right There's my first wheel blank And you know what? I'm feeling very like Kind of I think I need to go jump in the ocean Still some just soaked in sweat From all that digging. Yeah, I need to go jump in the ocean have a shower And then start with these wheels fresh. Oh good idea All right, I'm going to jump All right, I still have to fit the bearings in here Screws seem to be holding pretty well There'll be enough space and loop I have to Trim those screws a bit so I don't I Guess I could lay the metal little I'll get a dremel to Take off the edges of those screws You know what? I was gonna make all four of these and then put these in But I think I'll get one wheel totally finished First and then I'll mass produce the other three so I just need to make Some holes in here for that bearing to fit there and one to fit there and I need to write down on my little list of stuff to get from town next time I go spray oil Because I like to keep this stuff You know lightly coated with oil All right, I'm not gonna do any specific measurements. I'm just gonna Get it close and then check against the bearing Okay, that is right there. Yeah, that is really snug I Just did it a little bit deep just in case I screwed it up, but that looks dead-on So now I just need to carve it in deeper And I might need to carve it a tiny bit wider But I'd rather start with a little bit too tight. Oh, I just got that in. I don't think I can get it out Pretty snug fit. All right, I think that's it I got both sides done I did pull the bearing out of there and just put a groove in there so that the middle piece here won't touch Oh nice fit. Oh Beauty. Oh nice job Jamie. Oh my gosh. Oh, oh my god. Oh my gosh I'm both in there And if I can do that good job on all four of them Whoa, that's gonna be nice So nice It's kind of annoying that I have to trim off the edges of these Screws that whatever just use my dremel to trim that I have to put screws through because it's two separate pieces And I think I'm gonna use this size pipe. That looks pretty good. Yeah I think that'll be good Like even if it moves off a little bit, it'll still have pressure to push it back Before it gets to the point of no return Yeah So nice Whoo, whole saw. Okay, whole saw This is not not my favorite thing to do but whatever just to make six more of these This is a piece of I can't remember what it's called. It's some really durable plastic One of you guys sent this to me. So whoever sent that to me. Thank you so much I sent it a few years ago and I've only so far. I'd only used this little corner for something But man, it is really useful for these. So thank you to whoever sent this to me It's also nice when this cuts at right at the edge Because then all the bits they have somewhere to go Shoot out the side. I wanted to heat up too much You know usually when I do this I drill most of the way through on one side and then drill From the other side so that the piece is easier to get out I decided to just try this and see how hard it is If I can get the piece out, it's nicer to drill it all from one side because then you get a smoother Thing which isn't massively important. I guess because I'm gonna lay that anyway However, it is easier to get centered on the Pretty smooth circle I just snapped the drill bit off the middle of my whole saw thingy here, you know, it's this Totally stupid. I mean I have a replacement But uh, just just pay attention better Jamie. Don't I Very rarely do do that. Yeah, I just need to make sure I'm paying attention good All right, don't break another one for another 10 years and I'll be I'll be satisfied All right, Jamie pay attention good control slow and steady You know, I'm gonna turn you off for this. You know what? Check this out. What a gorgeous day out there Good stuff You know while I'm mentioning that someone sent me this sheet of plastic I should also say someone sent me this drill and this battery and uh, oh yeah, these uh These bearings I'm using for these wheels. Those were on my Amazon wish list Someone sent me those There's a lot of stuff around here tools and useful things that you guys have sent me and I just want to say I really appreciate it You know your efforts have not gotten unnoticed. Yeah, I don't make a ton of money on the videos, but you guys take care of me So thanks. All right, I'm gonna shut up before I get all super cheese This is the sixth one of these great this time I took my screws to the grinder and just smooth them out so I won't have to Cut the edges off later. I Want to get these in real fast and I melt their way in there there. I should be able to lay that into one of those Okay, right there. I was just getting one side smoothed out So that I can switch my jaws here and have them clamp on the outside and have a good grip Plus I have to get the screw out of the middle to do the hole here. Anyway, I'll get the other Two of these to this point What's about right close enough? All right now to cut the groove in there Luckily this thing has this part which slides that way and it was a good enough angle That's what I used to cut this. Oh that is mighty close. I think that's good enough. Yeah, that's good. All right Next one Those are so All right all within reasonable tolerances I just need to mount my bearings in there. Oh, those are beautiful. Oh, I'm gonna clean up that mess later