 This video is brought to you in part by TrueTechTools quality tools essential support Yeah, that's that's a problem We had flames coming out of the front there All right, so we got to know he calls should be hopefully simple and It's not reaching temperatures like 65 in there and they've been setting it higher and higher So let's go take a look see what's going on Now that should be at the end right here And draft mode is blowing No heat Nope, all right, let's dig into this and see what we got going on That's definitely normal, okay See what we got going on over here in this electrical section. So we've got a belt that's loose Is it tripping limit? What's going on? The funny is we have no alarm status here Alarm zero after the time this don't work surprisingly. It's working alarms enter current None history T142 Now this has been getting turned off and back on it could be a race in it So at least hold it and what sucks is I'm like We go up or down To 55 a 164 To 15 To 59 others just so many of them. It's just ridiculous. I'm gonna go ahead and get this fan tightened up Don't look like it's been oiled for a while Yeah, let me replace that Seven years ago Surprisingly no bearing wobble What I'm doing here is kind of cranking These in a little bit and then we're gonna move the nut outwards So we're basically giving it enough Bolt on the other side over here What we're gonna do is and crank this nut that's not turning right here to shove it over Four little turns do four little turns over here. I did have to loosen up the four bolts Out in the corners That still hasn't moved much This thing is nothing but a grease hole All the buildings got oil floating in it So it gets all over everything Getting better not there yet. This is tightened back down. I did get that tightened up quite a bit New pulley that replaced seven years ago is war a little bit. All right, let's take a peek at the filters I'm sure these are a disaster Seen had a box of them down there that needed could have changed Wow Yeah, this is an industrial application and they got really bad air like Oil in the air because they do machining and that's pretty bad I think I'm going downstairs and see if I can grab some and throw these in there. Holy cow. Look at that Yeah, that's sweet Yeah, you can see the oil It's Yeah, so three Six nine not gonna get this up the ladder by a straight ladder by any sorts Up she comes and you guys a thick rope there Comes in handy. So we got nine filters here. I don't know who does it if we do it or the maintenance does it But we're getting some new ones in here. See if that makes a little difference there I Mean we had no airflow from loose belt and plugged up filters. Let's go ahead and put a date on here That way we've got it. Let's go ahead and get this together Kick it on and see what happens. Let's look for short potential rub-throughs Everything looks Halfway, okay, like I said no Looseness and the bearing Think those have been replaced probably before I'm sure This squeaks. Let's turn it on and see what happens here. I wonder if that was on purpose Definitely ain't gonna run with it on hook so I might as well hook it up. Come on. Let's go run Get the cover off Faker won't hurt to take a look here. You can see we've had some rollback damage here done That's not a good sign I'm sure it's fine. No big deal. Yeah Yeah, here's a rollout. That does a lot of good heat on it Good gravy You'd think You put that thing a little down there towards the end. So it looks like we've got some newer burners Let's take a look at this heat exchanger and see if it's totally shot and maybe it's reason why it's Got issues look on the other side. See if we Visually inspect the heat exchanger still isn't coming on yet Yeah, that's that's a problem We had flames coming out of the front there. Holy dog crap And that looks like that is a self Resetting limit, which is a pretty dumb idea should have been a manual reset. Holy crap unbelievable So what I was doing while that was getting ready to kick on as I pull this panel here so we could take a look See what's going on Well, I'll go ahead and yank the last couple screws off here. The heat exchanger actually looks pretty good They've got these are actually stainless steel style. It's like an upgraded heat exchanger I'm not seeing Any rust any corrosion Nothing, like I said, this is an industrial application. So that's why they're running the best they can get But yeah, so we must have an issue with the burner area Let's go ahead and Go back over there and look at that again. Let's see if that's Getting ready to rub through to Get out of shake on the backside. We're good there All right, let's get this together and take a look at those burners boy. It just is not looking good I just took a better look at I thought hey is our plug missing there. No, let's get a little closer and take a little look See that Somebody something whatever Happened I mean it's supported there on the roof somehow this got shoved down on that broke I'm gonna have to try to take this apart and see if we can take it and go get it threaded at the shop I don't know if we have enough room to get on there with anything. This is a catastrophic mess right here, and I cannot believe they did a roll-out switch that is self-resetting That's just stupid When you kill power to it, it's gonna reset and try again like it's been doing. That's just so dangerous Stupid Try done screw it that didn't work so well since these wires burnt went ahead and cut them That'll tell me where they need to go. That's gonna be repaired. These could be chopped out and repaired Listened up that shop the flame sensor wire because it's too long anyway so we're trying to Maneuver this out of here Get all this stuff in the way That was a pressure hose. I Don't know if that'll pull off or not. It's gonna be nice with wood I'm just gonna throw some of this crap up here on top and Keep it out of the way Trying to pull it out in one piece that way. I don't snap it completely off in the valve Any worse I need to that was probably what came from the factory, right? Yeah, that's beautiful I don't know how we can get that re-threaded. I don't know if we can Not sure I know we could get a Pipe nipple and have the welders weld one on that might be the smartest fastest easiest thing to do honestly Or I can weld it whatever I don't care. It's At this point it needs fixed and there's not a whole lot else you can do with it so Unfortunately, that's all welded together So I'm just gonna take the whole thing All right, so I was able to have them take that right on there which worked out good So now we got a good piece on there. Just copied what we had be back over there and get that thing installed Yes, we have a full-blown metal shop and bought five welders It's not a small company by any stretch. I'm just one of the many We threw a little bit of great paint on there to make it look a little better Also protect the weld and stuff which he did a really good job. It looks pretty good. So a Lot better than what it would have been probably with a wire welder we got This back into place that's mainly surface area there if I scraped off my knife It'd probably go away. We're gonna chop some of these out. We're gonna chop some of this bad crap out All right, got our little doped up there Screwed on there before we get it in place Otherwise it will turn and it should not pull out if it does then it's not a good crimp So it looks like we've gotten most of this out of here that's all tarnished That's a lot better than what it was. This has been shortened. So we got less of that to deal with Got those back on there. These are weird crimp-ons a little bit smaller. So I don't have them. I'm gonna try to Attach these down below the burner that way flames roll up and not down Generally, I'll help protect the wire from getting damaged again if it ever happens again Hopefully not. All right, so we got everything wire tied up looking a lot better than what it did Got the ignition wire loose that way. It doesn't arc into anything always like that that way the Wire there it's first pressure switch somewhere got All them all done up like I said, I try to wire time low that way flames don't come back Sometimes they burn back in the burner. I don't want them to hit the wire things happen You know once it's you know up and going now I think I see what happened can see that that had to have been straight across like it was originally It looks to me that it was suspended probably by something before It probably had a block of wood or something under it and because you can see a wide spot there So somebody's either knocked it out whatever but that's what happened So I've got to find something to put under it But for right now I'm gonna go ahead and raise it up screw it together get it running It's on the inch or two there that's not hitting I Hit it up lowering that one just a touch. It's got a little bit of an angle, but Short of that is lift all this stuff up and then put a block under and have it knocked out So right now it is straight in line. So if you actually look at it, it's straight across Now if you push on it, it doesn't It's actually the way to support it onto the roof there same thing here If I can find a brick or something, it'd be great to put there as an extra level of protection But for right now, let's go ahead and kick it on and see this thing runs or not We're definitely further ahead of what they were We've got clean filters tight built Gas lines not leaking All kinds of luxurious things supply air temperature 59 outdoor temperature. I think it's like 30 something I'll give it a minute or we could speed it up. So I don't really feel like waiting Makes a little difference. They got he now. So that's the end of this call You guys want to see more videos like this make sure you hit the thumbs button click the notification bell Check out this video that video this guy that guy till next time guys. We'll catch you on the next one later