 okay guys so just gonna get this last connection going that's the the camera so we've got the camera connection a bit of five volt i know you can't see it very well from here but everything now is soldered i've saved some extra bits of wire so i decided to take the grounds away from the ec's what i'm going to do now is just pop this this camera connection back on so those little wires pretty much all where they're supposed to be it's going to be simple enough just to just to tap that on and there we go number five volt could have probably cleaned up these connections a little tiny bit oh sorry that's not going to seem to get my my hands and my eyes coordinated in the same the same way so there we go you get the cam on there but you didn't actually get to see any of that i wouldn't have thought so my big club ends in the way just twist it up nicely so that's it i'm probably just going to tidy this up a little bit more see if i can just wrap this round here and uh just just so it looks a little bit more um you know i can keep them with the other ones that will annoy me it shouldn't do but it probably will do just because of the way it looks but so there we go we've got everything on so we got the vtx connected here we've got the smart audio back on rx4 we've got the receiver on rx3 rxtx3 and uh ground positive over here and we've got the boy god my hope i did that correctly and we've got the satellite receiver and the magnetometer is connected and leave here somewhere that's how i receive is connected over here for power and on there rxtx3 oh three four therefore yeah four so so my smart audio then is now on oh down what did i do there tx2 rx2 i can't put it there i need somewhere for my smart audio to go because i don't think that's i think i've put that actually i think i've actually put that on s bus this is why i say you know yes you're best checking and checking again and checking again because hey we all human we we make mistakes it's uh you get into a little bit of a run on things and yeah i've actually put it on the s bus so that's not going to work there so what i'm going to do now is put it somewhere else like over there on cx1 i think i don't know why i did that why did i do that i think it's because i was going to put the um that's right i considered putting the receiver on tx1 but then decided it might be better just being down here because the receiver sits about here you see and i plug it like this so i figured uh that maybe be better than having this slightly shorter cable here and it not being able to fit in correctly you know it fits more like that um i tell you what i'm going to do i'm actually going to do that i'm going to just going to move this out of the way i'm going to take the uh just trying to think which one's going to be less of a pickle because that's going to go in at the back here and that just about fits so i think yeah i'm going to i'm going to take these off now i'm going to get confused of which wires which are these two because we've really got a very small amount of room to work with as you can see so all i'll do is i'll look at the wiring diagram for the receiver and then deduce from doing a continuity test between the connection up here and the wire down here which one's which and it won't really matter anyway i mean at the end of the day all that will happen is it just won't work um and i'm wondering whether even in the software whether i could turn that round anyway possibly but i'm not guaranteeing i'll get i'll get it the right way around or maybe i'll just undo one at a time that might be the way to do it do one at a time pull it across hopefully it's all gonna fit if it doesn't then i've made a bit of a boo boo but that's you know hey man that's life that is life so that was um that's the transmit this one is the receive so as long as i don't as long as i just prep this end as well always a good idea just to chuck a little bit of sold on the pads because there's nothing on there at the moment so if i just prep this end as well before i take that one off i still know exactly which one's which but i can just uh spawn the pads slightly don't want to leave on there too long on the pads slightly there we go that'll do because it's got a hole in it i don't really approve of those i mean it does make a great connection but if you do something wrong you know if you do um fall into like human error trap which is hey easy done then uh then yeah you can uh put a button i'm just gonna make sure that i actually get this right because i don't want to keep getting in the soldering it's quite a nice neat soldering job and i don't want to mess it up really so this is the receive so if i keep that transmitter my fingers and i'll put the receive on here i keep saying it you see i won't forget it i know that if i just if i forget it for an instant that means i've got to go through the plover of figuring out which one's which oh i nearly did it there i just questioned myself in my head and just remembered just very quickly received so it's 50 50 isn't it but if i just remember that so i just put this uh i can't stress as well as how much just a pair of tweezers is going to help you out doing little things like this because uh that will make a difference and actually it looks like i've got a bit more a bit more ease to go there as long as it doesn't mind having to receive i don't see why it should have mind having to receive on um i mean it's there to be used right that you are i didn't see that it had a special purpose looking like it can be used but it can't actually be used there's transmit i wonder if because there's a tx5 there as well but i mean that's going to be no good to me at the moment but it might be worth me doing an experiment to see if i can actually connect to um the uh uart5 in some fashion there we go okay so i know that's all going to fit so now we just got a um we're on tx4 received for for the gps we're on three uh tx3 for the smart audio and now we're on tx and rx1 for the receiver but there are the pads there for rx5 and tx5 and a dac all right um we've even though it doesn't look like that one's connected on the five volt up to the board of course i've done it underneath so i can still get in a chip as well without having the cables coming out the outside i'm much prefer when they're in the inside this one here i've got no choice about but the rest of it is all on the inside so i do like that of course you know the ones that are going off outside that's not the case of course let me just make sure i can plug that camera in probably better off we'll put it in the right way around there we go now this is because i was going to just have a little go out the other night it's a night vision camera it's the night eagle and i was uh just going to take it outside and have a little look because it was really really dark i've done it before but i just wanted to play around a little bit i didn't actually go out got a couple of beers and fell asleep on the set but there we go okay so right this is ready really to be um connected up with the uh video transmitter so here there's the video transmitter so that like i say look it just fits which is perfect i mean it's not going to go anywhere even in the crash um so we're just going to get the the bolts on there that's still going to be ideal uh get a nice little twist and if it's a little bit too long to my thinking i'll just twist it up a little tiny bit more that's fine and that will fit in for the receiver and of course that's going to go through the middle of the frame through the middle of the frame then sit into the back of the gps uh receiver hello my door just blew open like hello come in all right so let me get the nuts and stuff on and i'll put the top back on and the now so for this board um it's got the new firmware on i think i can't remember did we do that we did didn't we we did it the other day i put firmware on there um so but i'd also copied my diff wall which means that my magnetometer and those settings i can just transfer straight to the board again and so it'll have it for this but of course this is a different setup to what it came off and so um it could be wrong for me to do it like that but to be honest with you i really do believe that i did it when i set it up i did it off the craft um because of course there's going to be all sorts of noise coming from this i mean there's that much noise that when i do plug it in um you're going to hear it through the microphone i heard that the other day and i got a funny feeling it's um because this microphone is actually wired backwards they've used the ground as the signal and they've used the inner red wire inside the sheath um as the ground and so i'm not possibly maybe not getting um getting the amount of shielding that i i should be getting from a shielded cable so i'll probably have to take that apart and do that i had to do it anyway one ends because of the um the cable will come loose and i kept thinking my phone was going that's because it kept doing all sorts of silly things when i only plugged in those cables um the cable will come loose right okay so i'm gonna now just sort out my soldering iron and we can turn that off because i'm gonna say that we should be okay that little correction there was good i've looked over everything else keep looking over it while i'm doing i'm just going to sort out that little vcc because it looks like a bit of a blot there just wants to look a little bit neater but i don't want to disconnect the wire at the bottom because again i've i've done those wires at the bottom i'm just going to have a little look at that because i've got a funny feeling with me just doing that i've disconnected the ground but no i haven't it's quite small to me see now i've just i've got a message from my opticians telling me my glasses are ready to go and get so that's going to be fantastic and no no that's not exactly true actually because you can't just go in and get them these days you've got to set up an appointment to go in there and get them um because of the old uh come blue and so we're going to stick a large bit of i don't know if we can see that on there there's a nice bit of sold one there just so i know like those in it switches off the air is not going to get to it and start gnarling up my tip all right okay guys so what i'm going to do now is i'm going to go away because i do need to get something to eat i'm not eating uh this morning so i do need to get something to eat and i'm going to come back when i put the nuts on and i'll put the top on um and then we're going to see about positioning the gps well it can only go basically where i want it to which is right above the stack i want it to go position central so i want it to be as central as possible but that's what we got so far i'm hoping it's not looking too gnarly because when i first did it and was quite tired you know i was quite quite happy with myself for it see you in a bit