 Okay guys we've got another pressure washer here the Troy built 2550 2.3 gallons max but here's the issue you see that the rope does not retract back into its little home so we're gonna pull the scuver off of here and check it out I gotta do something about the lighting because I'm trying to be in the shade but at the same time I even have a light on there that's just kind of kind of hard to film outside but let's get you set up here and let's see if we can find out what's going on with that okay guys so looks like looks like someone's had that one off so let's go ahead and take it out now I don't know if he tried to look at it we got one here we're gonna take out and this this cover piece here should come off again sorry about the lighting it's just so hard to you know I'm trying to stay in shade yesterday real feel was 107 so and trust me it really felt like it okay so we're gonna just pull this up through there now looks like okay we're gonna take the take the gas tank off but if we have to take this off the top part here it could be in trouble because they are riveted in there I hate that I have drilled the rivets out before put little bolts in but hopefully we won't have to do that hopefully we can take this off and get some lubrication up in there and go from there so let me get looks like a 516 okay guys I got the 516 here got it that one's a little rusty like me okay take these out of here I got one more on the bottom it looks like 716 I'm gonna have to get a wrench for it okay so happens to be a 3-8 and it is cooking out here it's noon front door just opened up on the house but so I got it on video monkey sitting in there in the living room I was right here in the garage and it came open so I'm not sure why I did that's never done that before no one opened any doors or anything like that so winds not blowing unfortunately okay so there's that one I've got this little spacer down underneath it okay now we're gonna pop this off of here alright let me let me give my attachments for my impact driver there's four on here I hope I hope it's just you know lack of lubrication or something because I don't have parts that will fit this before these bolts there are three eighths as well two on the back here two on the front and also I got to get while I'm thinking about this let's go ahead take that screw out for the dipstick to dipstick that one okay now two on the front I think the springs broke so that's not good depending on where it's broken it's a broke at the end might be able to fix it but let's stick this out it shouldn't pop out on me these are called dogs they come out when you pull the rope centrifugal force pulls them out and they lock into that cup there and then as you let go it flips them back in so go ahead and take these out and the springs broke I may be able to weld this I don't know if you can see this that's part of the spring here's the other end I have welded them before and I think that's what I want to try to do with this one but I got to take it out and in order to do that I'm gonna have to as well lubricated we have to keep the spring from popping out on me so maybe put a zip tie in it or something I'll probably just go ahead and take it all out because it needs to get clean before I try to weld that so but that's where it is I have spent time and bent them before but that's that's way too much effort trust me okay guys there's what I got set up I made me a little jig I got them tightened down so I'm gonna put my clamp on here and I'm gonna try to tack that I don't know if I can get both sides but the weld should be strong enough to hold that right there we'll see I'm not gonna show you all in that cuz it's just gonna be attacked okay so I got attacked on there so what I'm gonna have to do is I've got to put this in here whichever way it goes I think it goes like this and then I just got to keep twisting this around until I get it inside here so I want to do is just keep twisting and twisting and twisting probably get a needle nose pair needle nose pliers and do that's what I usually do it with so hang tight guys and I'll be back with you okay so that's pretty easy now we're gonna put our dogs back in here like this just like that I had of course take the take the pull rope out of it looking like it could it's about do for another pull rope and before you get this on there and tighten it down make sure there's little channels in there that you got to get those little dowels into and that helps slide them back in I didn't put any more grease in there or Lou or anything cuz look like it had plenty all right now let's see here I'm gonna pull the rope out this way and I've got a got to get this spun around here and we'll put the rope back in it which is not that hard to do okay that's all the way so I'm gonna line my hole up with the hole on the on the shroud and see here screwdriver just gonna stick this in here just to hold it now our rope I got to get my later I'm gonna melt this end a little bit okay so did you say I almost grabbed that screwdriver and pulled it out there what are you doing in there and then that'll just go whoops and just got to get it right hope if I could see something but a lot of times you can cut off both ends and just shove it through this way there we go there it is now we're just gonna tie a little tiny knot in this thing here just like that little knot put it in there give it a tug with that out now let's see if it'll bring itself back in does I should probably go one more around with it I think that's what I'm gonna do but I can do that without taking the rope out by pulling that rope up in here there's plenty of room and then just going around the rope there we go I'll put this thing back on just reverse just just those four bolts and well let's see four or five bolts and those two screws on top so yeah I'll speed you up through this we got it I'm gonna start it up not hooking the water up and all that just to start it but I will well it almost started there but I've been careful all right there's that one it's fixed we have that thing over there it just needs the cable for you know the safety bar thing and we'll do that one so I got another pressure washer video coming up but it's gonna be cool all right guys there you go thanks for watching hopefully that well it'll hold it should I seen a guy cousin Kev you heard me talk about him before actually JB walded one together and I told him it wasn't gonna work it's working look it's working on an old tiller old rototiller for his garden three days later three years later he was using it and finally it started having a rod knock but that thing lasted three years and I don't know how he got it to hold but he used it once a year but still I mean of the thought of it I didn't think it would hold I mean you know just pulling on it but it did so all right guys I'll suggest that he gets another one that's up to him if he wants to I'll put it on for him if not well you know if and when it does break again you know then he'll have to get one but I'll recommend it to him see what he says thanks for watching guys she bears a mental edge I'm gone for now we'll see you in the next one bye bye guys and take care he's playing havoc on our batteries man just too hot I'd put that on the charger