 One, two, three, then this is going to be slotted on the end and then our steel gets pushed against that and then bolted like it's bolted into our steel. So we've got our five bolts in that go right through. Wednesday Alex yeah? Wednesday. Wednesday at ten to nine left the house at half seven but we've been picking stuff up, forgetting stuff, going back to pick stuff up, back up. What did we go? We went for cement and dye which we got, got our way back to the job and remember we need a padstone so I checked the drawings and he specified 250 by 100 by 150 so we're okay to use a concrete lintel so we cut that into four there's our padstones 150 deep reinforced as well. There's all our tools we've got some eight before sheets to put down on the slab to protect it while we put the trestles on. As you saw yesterday, the steels are here and all the bolts so the rubbies have been not nipped back off again so we need to get cracking now we need to get the steel around first so we've got a bit of remodelling to do when sizes are decided I think that's getting reduced and that's getting knocked down but we'll see. So we need to get that crap out of the way which we couldn't use up yesterday get the steels in the hole actually the steels are gonna sit on the wall because of that that long and get the trestles up start knocking a lot of this lot so yeah we'll get back to you in a bit just gonna get this steel these are actually quite alright after the ones we did it and go. Not too bad at all. Let's see can you still grab it if I put the camera on there yeah. Ready? We'll back up a little bit as well so you can I don't need to. Sorry for any turbulence. So where's it going on top of the steel wall next to it on top of it just right on top one two three we've got to lift the top of the web otherwise you won't get your fingers out okay okay down normal slice for steel where we're putting the steel so there's the ends of the joists which are currently propped we're gonna be chopped off and this is gonna be slotted on the end and then our steel gets pushed against that and then bolted like it's bolted into our steel so we're working around Robbie and Robbie on this one so once they've got the timber in place we can fit the lintel so we've done our bit now so we're gonna leave it for them to get get the judge cut off get that put into place and then we'll come back after dinner and get the steel fixed in place so there's still plenty to do the time is but it's after one now no half 12 not so bad I'll leave it on time that's why Lee's like to working on it and we'll go off right there see you in a bit so just take it up and hook it on yeah see idea okay you've got to go to that corner one two three nice don't let go yeah it's like the top goes isn't the whole steel looks like it won't you don't really dropping it do you you following the choice so yeah yeah be a thin piece in here I'll put them out of the blocks yeah especially in block where's that we only put a steeling we put a bed on top and just wind it up with it yeah obviously I think you know it was going to be split or something above in here anyway because you said it wasn't where the course the timbers squashing in it do you want to swap that timber put these two in now yeah so now we bolt into place and then we can take the props out can't we and we can put an echo under there then just from the one under the steel once you've bolted it then we'll echo it and I can get it packed up then tomorrow so this coming in now is that many holes don't we we must just give us a few to choose from there's nine holes they did mark that side with a circle I think we just alternate them well you how many of four we've got five you've got four we've got four yeah okay so there should be five on yes and there's nine holes yeah and they're all 12 mil I think the day them ones them ones are for us so that will be yours yeah that one yeah get that one yeah and get that one point to that hole that one yeah so the steels in temporarily now it's going to be drilled and bolted and then we can prop it on the echoes and take these props out and get it built up probably tomorrow oh yes a little bit of music over that bit for November 10 to 8 sorry 10 to 9 flat boysling night which can't wait for we'll go here early today because we've got a lot to do but we've just been sat in the van for the last hour that absolutely poured down as you see everything's absolutely soaked which isn't good but um we're on with this anyway get this get these steels and then bolted up and everything so um yeah we'll crack on with that I think while I'm up there finishing the patching on the inside what you're going to do Alex tidy up get rid of the bricks move the bricks yeah let these let these blocks go dry a bit because they're absolutely forgot to cover them last night that block where once a good scrape yeah obviously that was pointed in the dark so yeah everything's so come wet don't you just love winter so yeah we'll um we'll get back to you in a bit when we're back up there right sometimes when you're cracking on because because the weather's threatening and everything's wet and you're just getting on with it you forget to film so I've just forgot to film picking the steel the steel stat where Alex's foot is on the block each side so we just did it straight up and in I wish I could have filmed that because we've struggled and all the others and that just went in dead easy didn't it the odd decent sized steel though so as you can see yeah Alex you show them show them at the top where I've patched it up at the top on the inside so since this time we can't wind it all the way up to the top and give it a bed we have to leave a bit of a gap so what dad's done is one second he's uh put some cut some blocks down with the grinder and packed them in and pointed them all up nice so I ain't going anywhere it's nice and packed up just got to point up the last bits where the accros were and then yeah and then we've um the robbie robbie drilled the holes for us yeah it's already got the wall plate bolted into the web that's what the four bolts are yeah because it's because that's bolted into the web then we can't get our bolts on either side now so that's get along the threaded bar so you can bolt it through through the steel and through the wall plate so it's going to be so that that's basically now nine bolts of it yeah and then we have the nuts and the washers so we space it with the actual nuts yeah it's a matter of getting into vision now leveling it all up putting the bolts and everything insulating between the beams and then building companies it proper solid first mm-hmm it's a no good way of doing it but it's gonna look smart what it's doing and if you look there some of the holes didn't line up so robbie had to get the metal bit and punch into the hole through yeah because it didn't line directly up with the joist yeah so that's the two long story short it's not going anywhere once we've got these bolts through let's get it up into position let's get it packed yeah right today speed bump another speed bump uh yeah the steel's too big so our padstone is going here so the steel is going to go over by a hundred mil but the padstone is going to take the weight of it it's going to be 150 minimum the only reason it's 150 minimum is because we've got to get this in i think i've shown you this this is the wall plate so that's going to run on right across so that's got to go in there with the outside skin is our padstone goes in there obviously a bit higher so and then the wall comes down there that's coming out to there so now we need to get this bedded in packed up this steel now is solid we've got it leveled up with the steel inside lined up all the holes lined up well i'll come back to that in a minute so it's as you can see we've packed it in so it's basically we've got to go cut all these pieces and get it all pointed up packed up but as we said two of the holes didn't line up so Robbie has a re-drilled them but we haven't done this steel so two of these can't be put in i think it's that one and that one we can put those three in for now but we're going to have to get a drill and come back and drill these out which is a one of those the old saying pain in the ass but it's not stopping us today i think we're coming back sooner just to have a final tied up and everything probably finish that wall off because not on that wall yet so gonna have a brew now and then start cutting the blocks for in here and piece for in here get all this built in leave that pocket out for the robbies so yeah that's it come back to you in a minute after brew still slow going on the concerto job we've just managed to get all the bolts in re-drilled that one re-drilled that one the plav we're getting all these in because you've got to thread them through through and you've got to get bolts on the inside of each you have to get bolts on each side of the steel to clamp it we have to come through this timber that timber there there's one through that timber which is real tight so we have to thread the bars through couldn't just push them through we've got a couple wrong so we must have been on that about two hours just to get that so it's all together now padstone is now patching at the top and then we can board it up because obviously we've got a big hole now and we're going to stuff the gap between with insulation we've run out of insulation we've got plenty more at the house we can bring back so that's it let's get this patched up we're done concertry is done oh no it's not i've got the internal wall to finish yet but anyway steels are done there's our 150 seating the it overhangs by 100 but like i say that's where that's going in so we can't we can't do anything with that until that's gone in um i mean if the building inspector doesn't like this overhang we can always come and cut that off but i can't see that being a problem this is self-supported we didn't even need to prop this that renders that hard the blocks haven't budged absolutely solid so we've got all got our five bolts in they go right through it's also bolted four times through the other steel so that that wall plate on the inside it's got nine bolts going through it so it's going nowhere this is all absolutely solid um you'll notice it's sat on the there's no acro support in it and it's sat on the pads are wet but this is it's sat on these at the moment these are holding it up so these are coming out when the wall comes out in line with that pad so that's coming out saying cut down there and that's coming out it's a nice big opening and then the ceiling as you can see so the ceiling will go straight through with no drop down we usually have the beam a hell of a lot of extra work in that but um that's what the customer wanted obviously it's custom work it's got probably double the work but um i think once it's done we're worth it yeah a lot of work going into that robbie and i was here for a good day as well doing all that i've got to get it boarded up now so that's what i'm just showing you now so we'll leave it seeing a bit boarded to five it's supposed to be in Liverpool at half past six so that's it the conservatory is finished the steels are done brickwork's finished there's a tiny bit of points into on that corner and that hard to fix that i freaking pulled off with that i've seen yesterday it's kind of rushing the dark but anyway there you go that's a quick one so stick with us i'm going to come back to you straight away when we're back here on sunday when we're doing that wall there and then we'll sort that out and then we'll do a final walk around and show you everything show you inside as well and put the insulation so catch you in a minute a hell of a hell of a lot of it