 Hello hello Just getting some last second things tidied up here everybody Think we're about ready to go And work on today's project right so first off yes I'm here And I'm back with you With a new haircut right look I know it's a big surprise probably right on my long hair from the last Episode is gone the last wild hairdo Summertime and actually I give myself the haircut and so this is the only haircut. I know how to give myself There's only one haircut so it's just wait until that time when I actually need the haircut and It happens like once or twice a year and So first off, thank you for joining me today. I see some people rolled in the Chat here PO 17. Thank you for showing up Steven kukamanga Thank you for coming roll Pats. Good to see you here pretty blue things Hello from England. Thank you for coming Rice oroni race oroni. Excuse me. Thank you. Thank you for the compliment. Thank you for being here. All right, so I'm first off. I'm on a Excuse me I'm Here to you today with you today after struggling my goodness myself for the last I'd say entire week with Streaming problems with my streaming PC this PC that you see here. I'm using now It's hopefully stable. This is the first test. I've run on it since I've installed windows about three times and It was just craziness. I'm not sure this is hopefully gonna work fine But the problem seems to be after I do something like this and reboot So we'll see after I reboot after the show today if this PC will survive. It's been wild I thought it was the RAM. I thought it was the hard drive. I Swapped those out. I even tested an entire like built an entire second PC and it's just been a mess Hey Little ex pig. Sorry. I'm actually glad you're here because yes. I I'm holding scissors, but what happened so here I'll tell everybody. I wasn't actually gonna say this because I had never chance to send the message but I Cut I also cut my phone or my foot really badly when last week like my toe right under at about an inch and I Probably should go to or should have gone and gotten like a couple stitches put in it, but In America, you know, you go to the emergency room for certain stuff like that and The even with insurance you'll get hit for like five or six hundred dollars. So I'm sorry. I did I cut my foot and then I've been trying to heal it and Hopefully I'll have it fixed up by today. I kept it clean and and the wound is okay. It's just it's pretty big it's right in between with my toe and crevice is like right here and So that kind of made it where I haven't been able to Do much with my feet all weekend and so Yeah, slap some wd-40 on a good idea. So anyway, I wasn't able to leave here after that So I'm going to Hey, Felipe. I'll send you that Today, I do have to go out there. So I do have to leave. I'll I've got the package right here, but anyway Besides the foot thing and the PC thing and the haircut thing I do have the new PVM and that's the one you saw over here in this view So if we go back to the shop view Thanks, Ben. Yeah, so this is the hey master's safer Hey, Felipe. Yeah, I'm sorry. I'm usually all over that stuff, but the foot cut really After after all that you can see look at this. I promise. Do you see your box right here? I have the fragile sticker on it. Funny enough. It's sitting right there on my list of things to To do and to send off which is funny. All right. Here's that PVM. We're working on today and so It's you can see from the picture on the thumbnail and the picture in The video from the last episode that it doesn't work Well, you know the power supply wouldn't work. I've got a good power supply What I want to work on today is actually the deflection board kit so we're going to do that and In order for us to do that I'm going to Get over here. I've got the circuit board right over here and let me show you this so this is the main circuit board on this one and I've already pulled it but if you want to see what it does you can watch that video and If I can get the system to pull it up We might pull up a clip from that where we can see what it looks like after we repair this So the the issue I'm hoping And most likely are the capacitors which I have marked off which you'll see here in a second when we look closer at the board from the overhead view I've also got that capacitor kit here Which is based on another cap kit that I've made in the past for the 51 and the 54 And I've added a few capacitors here to the kit and We will remove all these replace them reinstall this and test it So that's the major plan here today And we shall do that um After we do one more important thing, which is cleaning the HECO FR 301 So before I even get into Actually doing The work I'm going to need to Oh There we go I'm gonna need to clean This guy get some more light in here Get the overhead view kind of straightened up So yeah, it's just been non-stop problems with the streaming setup since I had my flood incident So I thought maybe nothing had happened, but I think something was interrupted disrupted Hey Dwight Dixon. Hey dr. Tricks Hey chris Good to see you all here so This should be cleaned anytime you're doing a major job on a circuit board is any importance, but Uh, look at my chamber here. This is normally completely completely cleared out but After years of use it gets nasty But that's not what is really important here The important things are just to make sure there's not a large build up in there So we're just going to look in there and just take this. This is fine scrape that around Make sure that chamber is nice and cleared off go ahead and put the front piece back on there Hey jackie craft. Thank you for coming in today and Ooh, there we go. I'm just popping out There it is See that little piece of solder Looks like a jewel fool's gold Uh, just clearing out the little tray dish here should clear that out for sure Next we're going to take a look at the filter back here and um This one wasn't used very much. So I'll probably try to reuse it since there's not a whole lot of Debris on it yet. So we'll reinstall that And now we can Get this chamber put together Now one of the things I have not done So the chamber is good right there. One of the things I've not done in a long time Or at least between like three or four jobs It's cleaned out the back chamber Which is important. I have done a video on this and You need to do it every once in a while. So when I release the trigger here and Get some of these parts out of the way And then over here We have some screws Now we're not worried about the big ones in the corners because that can that'll take the whole Top here off and you'll actually access the air diaphragm in the bottom And then what we're just trying to get to is the little I'm not sure what you call it valve cover here that's under The top layer. So we just need to do the two screws Smaller screws get those out of the way that comes out of the way and this is what we're looking for this thing right here And we can just remove it And this one's been used for a while because even after I clean it It still has a yellow A yellow almost Flux residue color to it Yeah, I did get a haircut. Thank you snuffer stiffer Dwight Dixon. Thank you Let's look Look at telly. Hello. Hello. Thank you All right. Thank you. Yes, and thank you. Thank you, Ben. I'll take a look at those pictures later today I'm sorry. I wanted to get this tested the streaming tests uh, done up And hopefully I can move on from that because I had to spend a lot of time I mean, I guess that was the thing that was positive about having a foot injury is that my My streaming PC was broken. So it was mostly stuff I could do down in the basement by myself, but I spent probably 25 hours Oh, there we go. Let me move that up a little bit and you can see the rest of my hair. What's left of it at least I'm getting old man. I'm about to be 40 and um really soon and Like I don't know. I think maybe my hair is, you know, finally It's obviously not growing In some spots like it used to but I'm always wondering if well Am I gonna lose my hair? Is that gonna happen? Will it make me look more distinguished? Who knows Only time will tell. All right. There we go. Sometimes you got to be careful because I almost lost um, I almost lost the piece but what I'm doing here is I've got some isopropyl alcohol And I'm just cleaning out the bottom of um the inside of The cover Where that air comes in and out. So what's happening in this piece is This is where your suction Is being pulled from it's like sucking in here air, right and it wants to suck clean air So that's why you have this chamber Essentially in front of it because this chamber is your filter pretty much where all your solids and then your tinier pieces get caught up And then you're just getting vapor That passes through this final filter and then that's going in here And it's actually being sucked into the motor Where uh, the motor's pumping air through it self circulating in here So that's happening. It's been sucked in and then what happens is is since it's vaporized mostly over time and and you know you use Flux or you hit um, you hit Flux on a board where a part is installed to remove it You're sucking that in and you're vaporizing that and then you're sucking that vapor in Into the chamber and it's being sucked through this filter and ultimately it hits this thing And that's why this will get sticky and if you never clean this you'll think your your tool's not working anymore It's really easy to clean and if you do break this little piece Uh, if you if you break this little piece you can get another one Directly from hacko and it's cheap. It's probably under four dollars because it's it's little more than a piece of plastic, but you can definitely get it from The supplier I have I tend to keep a couple of these in the shop just in case I need a new one But most of the time you can reclaim it like we just did there and that's it and you're really gonna help improve the performance of this guy And one last spot to clean out is the bottom here just to make sure that it's nice Clean in there The inside and that alcohol evaporates really quickly And I'm just hitting up with some air And um, you know, like I said these filters are here and you can obviously get replacements to and change those as often as you like Uh, but definitely check them because they can get very dark and then you're definitely going to lose a lot of suction power. So you'll want to You want to change those if they're needed to be changed. So now we're ready To rebuild Hacko and this is all pretty easy to figure out. That's all set up a certain way It's like that Whoops But we just need to screw it in And there we go. Well, I'm really Really hoping the streaming setup will Stand strong So I can stream again this week because it's monday and we made it happen I'm happy about that and I'm hoping We'll get this circuit board done And then we can work on the power supply separately Um in another stream and get that fixed too. That would be a perfect like week And then maybe do a third stream But it's all dependent on the software hardware combination All right, we're back we're going to just slip our Hose on here and again if anything happens to any of these parts or you think they're suspicious of you know degradation and Robin you have performance then go to hako's website Directly hako and what as long as it's a region that hako will sell to You can buy the parts directly from them. You know, you're not getting generic anything And um, you can replace the parts instead of cleaning the parts like I did today You could replace them And you can actually replace even more on this if you Have a bigger issue. So that's the back end. We've got the pump cleared up up to the filter Now we need to Get our filter back in place in our chamber And everything is good and now We can plug it in let it heat up And then we'll be able to Check out the chamber here So again There you go, you hear that That's the pump sounds pretty good sounds like we're probably clogged up here So I generally like to turn the heat up a little bit on the dial a little over two I do use this stand 633 hako Just because it makes life a lot easier And it comes with the 50 or 599 b under there and For nozzle and tip cleaning What a mistake From the kit here Does sound like a pig So the good things to use for this cleaning is this little tool generally and these are all things that come with The pump when you buy the kit to begin with all that so If you if you notice it's probably gonna be difficult to hear there But it is cleared out You can hear it actually sucking like through this little hole so You should be able to go clean through there like that pretty much Um, you don't want to hold this in there too long because it will just don't send the heat back up to this coil It's all metal. So you just do something like that There we go There we go And this is just if you need to take that barrel off And man, just like if it's like hot and you have a clog You can actually use this safely and it doesn't burn your hand or anything. It's like heat proof I mean remove that barrel Hey, thank you egg 64 for the $10 super chat. I really appreciate it said thank you Or thanks for keeping old stuff alive Doing the logs work Do you are or do you do rgp mods on pvms? You know, I don't know that I've ever done that myself Uh, I had someone that was supposed to be having that done on a monitor and The monitor well dubbed up being so badly busted And not Buzzel bested but badly busted that it uh, it couldn't be couldn't be fixed so That project is what we call an abandoned project now now remember to And thank you again for the super chat remember to when you're using this. I'm sorry I don't have the convenience of a Sorry a little stream deck anymore so We've got it cleared up everything's good Let's sit in here like this on this on the edge our workspace here And We're fine It is ready and that Should be that but always remember to go back here in your dial and and I usually I'm gonna be honest with you there's very Rarely times when This um You need to have this set over The one on the dial always remember just just Turn it up if you need to clear the clog in here And otherwise keep it down around that lower number if you're working on circuit boards That's so that's my experience you generally don't need to go that hot Unless you're hitting a spot that has like a lot of solder on it And it's a big point with a lot of heat on it which there are some capacitors and power supplies that you know I like that but For today's application, we're going to be keeping the temperature nice and low That's because we don't want to have a solder burnout and Sotter, I mean a padburn Looking at Removing these capacitors And as I said, this is based on a prior capacitor kit that I've done on these two um models And it's about 13. It's an older kit. So I wanted to go through here and expand that a little bit more with some other capacitors And update for this board. I'm not sure the value on this. I have a good guess as to what this is But I'm not quite sure what that value is Uh, but we can pull all these and hopefully that'll correct all that terrible geometry that you see on the thumbnail for this video After we replace them So, uh, let me grab the circuit board again And I'll try to wear this most of the time this grounding bracelet And that way we won't do any damage to our circuit board, but the the areas that We have deflection issues are going to be from this area down here. Let me give you a little bit more light kind of that And I've already marked them all With a dot here the ones we're removing And so this is all around heat sinks. You'll notice that so high temperature stuff Uh, we're dead. These are all for sure problematic if they fail They caused those red green and blue lines. Well, no, these don't these will cause deflection issues red green and blue lines Actually come from the failure of this capacitor here. I'm touching right now And this one. Sorry. Those are the two these two That's why if you look at that video, which we'll look at after we fix this hopefully These two are failed. I'm sure of it at least one of them is these control deflections Other parts also do like these Specifically and there's some more down in this area. So I need to remove all of these the ones that have little dots on them I added some other capacitors, but you'll notice in general, they're the ones that are right up next to these Areas where a lot of heat is generated, you know, so that's That's why That is necessary. Let me turn up a little bit more of the background music. We're gonna hover around You know A nice little level there because we're gonna start this desoldering. I don't want you just have to listen to all that All that suction happening I do have some meters here if we need them today. I've got a fluke meter and then I've got a handy dandy capacitor tester And we can test all these things That we need to that we desire to if we have time We remove these parts from our circuit Because we could test them in circuit, but I'd rather just remove them in circuit And that way We can Get a good reading on them and not because honestly, I've used the best tools there are and I still run into an issue where I don't Get Well Sorry about that. Let's get all these tools put up and we're just going to jump right into this Here we go. All right So I'm going to try to do Is remove The capacitors like I said with the dots on them Try to give you a front a front Door view Your view may be better than mine But I don't know for sure I do know for sure which capacitors I'm removing And I will bring in this extra set of hands if I need them This first capacitor is right down in here. I've got it on the leg And there you have molten solder Okay You can see that that leg is broken Three just if I can get you in closer. I don't know if I can And keep it in focus I'm going to give it a good shot though. Let's see See if I can show you So here's the one leg I've already removed right here Where this up right there in the center of your picture where my Tool is this right here That's one leg of that capacitor that I'm removing It was quite a bit like getting hung up on that but as you could tell now Look at that. I mean if the legs are completely free I'm going to pull it out This is a 25 volt 1000 microfair capacitor Alina branded I'm going to guess 105 degree rated Oh See this is the reason we have issues. Sorry. I'm going to let the focus catch this Okay, but it says it's an 85 degree Celsius capacitor and it's from Like 1995 94 ish So these are not too trustworthy. So that's one down It's always a good idea to come in here and um, this is 586. So Yeah, 586 was supposed to be the 25 volt 1000 if we look Right there right there one of the new additions to the kit So that's good Moving on Um, I you know if I ever have any issues someone was asking here last draconic Hey jamespoon Thank you james. Uh, I did So if you are using this tool Uh, what are you asking again? Sorry, how many Jobs do you do? I mean it depends It really depends on the solder itself. How easy does it pull? Do you have to add solder to the pad? Sometimes you have to add solder so, um It just depends on which solder you think send there you clean Just clean it anytime You feel like it needs to be clean you leave them more on safe instead of, you know, waiting too late. So It's good to do it in between every job. It's before or after you finish a job So I got the first leg there. I don't know if you can see any of this because it is so Um, so much going on in here in this floor. I'm gonna try to balance this back out And see if I can even point it down in the picture. I don't know if I can Here Is the leg I just broke free right in the center And see it now. I'm sure Where's Waldo? and We like that and now we have both legs free Do they both way going down there if you have a really good vision you can see them And we will pull it Oh Yes, feel good. So this is a 50 volt 10 but the problem here is again, it's a 85 degree capacitor and Made by jemikon, which is not terrible jemikon is not terrible, but you know 85 degree By normal capacitor. It's it's too old To be trusted especially when it's been around this hot heat source again 50 volt 10 that is 577 And it's good. That's what the list says Now we'll move to the next one, which is not uh, not too far from that one like a little bit below where we just went The biggest thing here is Precision precision And On where you're touching the end because there's so many other components under here that um rely On each other. Oh looks like Cole's excited upstairs. Well, what's going on up there? He likes to bark at everything all right Gonna pull this with the There we go Here we have Oh, this is a 10 volt 105 degree though 10 volt 100 micro farad capacitor. It's pretty low Um, I know I didn't replace it with the 10 volt sorry 15 17 16 volt i'm going up to 16 volt probably 25 volt honestly Because I have tons of 25 volt 100 Micro farads and that's fine to go up from 10 to 25. That's a big deal all right good Hello, princess peach. Thank you. Hello Yandy All right, let's keep rolling. We've got three out um, and we have 16 total to pull from here, so Probably start moving a little bit quicker now But you know how I like to roll. I don't like to do things quickly. I like to do things correctly so there's other So I don't want to mess anything up most importantly Let's see about getting See 541 now some of these are just An absolutely wild places actually we're going 523 up here 523 I'll say another tip Soon in here as I start to I'll hope this heats up and I'll see this one's gonna need Some of these are in spots where the heat is higher Tolerant so um Probably going to have to reflow so I'm definitely gonna have to reflow sod on this adult again if this happens is normal You don't want to just get in a rush and actually damage something. Where am I? I'm right here I'm going to try to get the other leg, but it's on a ground plate and it's negative So let's see We can get it to You know we got it we got it nice and broken free, but the other leg Needs Some fresh solder on it and that's what you do if you run into a situation where You You know instead of trying to work with what's there, let's add some fresh solder And it should Flow right out. I mean it's starting to wiggle free on its own But let's just We might even pull it and then just Get the solder out of the hole. Let's see that might be the best force of action or It's made of little solder, but So don't want to get like in there. Okay Should be good Just like that Well, I tend to go I think we did talk a little bit about Temperature on the tooling I'm what I'm trying to pull it out over here. There's it Get the spoke blades right there it is 50 volt one That's a little one Again, I'm saying about 23 good the The temperature on the irons trying to stay around 700 degrees Fahrenheit and then I go the lowest temperature possible on the desoldering tool The very lowest the number one setting All right, we go on and move on Here we go. You can watch them all sleep. That's fine I probably did the same thing. It's like It's like Watching go off or something And I'm trying to get a better view of what I'm targeting next to a removal targeted removal all right I'm going to go back to this section and we need to get 541 out 541 Okay, I've got 541 ready It's right here on the other side opposite of the surface mount component Wiggle that capacitor with your left hand Move that and hopefully it breaks free. Where are we? Oh solidified itself back. You might have to do this one again It is right near right That is in the house Yes, as I try man. I'm trying this string set up. Hopefully we'll make it Uh, I had to have to reset my sound settings so many times and uh I think I used to use a sound gate or noise gate And I stopped using the noise gate So that's why you're getting actual sounds this time before if I didn't talk just wouldn't It just wouldn't happen. You wouldn't hear anything much less to be soldering to all right. I'm trying to get my finger back on the back side of this and uh, we'll push it kind of Get the solder molten and pushes all the way out of the can Surface mount component, that's good. Of course now I got a beautiful solder going on here Do I have to undo? Where are you baby? The shortest, beautiful solder well Oh Come on, baby There we go. All right. There we go These ones are just a little bit tricky to get into and out of and make sure you pull the right ones and another jammie jammie jammie jammie jammie con 54.7 85 degrees Celsius for your Pleasure dirty under there Yeah, I know that's what I thought I didn't realize The noise gate was on and I just think I just followed something and said do a noise gate and I was like wait a second I don't really want that so in the reset. I've not been adding that I've been adding a little bit of a You know suppressor Samuel here everything. That's awful because I still have my boiler All right, this is a 50 volt 4.7 541 and that matches our cap kit So we can go goodbye. There's one more over here. You'll notice That's kind of tiny in between big Chungus here And that's this little guy down In this corner, so I need to remove it probably next It is 529 529 or bandit We're uh rolling up in truck it baby We're gonna do what they say can't be done One way to go I don't know Really liking the solder quality some of these points over here Actually, I'm gonna go ahead Reflow solder on this one I just don't like it. There's not very much on there. Sometimes you're not presented with not much of an option There you go. And again, this is an awkward position one. So we're not gonna I'm gonna push those two parts Lyrics or something going on Change it in a second I love it over No, I could if anybody's like listen you buy you have this on it's probably bad stream Nobody in the office could be playing this in the background because it just sounds like you're watching a video of a man Foggy Oh, you went to the park show It's why it says is the only one here anymore It's the only one remaining in the chat Thanks, says We miss you It's glad to have you all right 50 0.47 529 C5 29 And this one's actually a ruby con check it out. Nice Ruby so-ho Ruby so So tough. Where's Ruby's tent settings 105 degrees, baby Lovely little lovely little blossom there All right A couple more in this area. Maybe we should skip them out of the way Everything else is kind of bundled together Almost got everything out around This is the one I'm not sure about On your screen now. Oh, that's okay. That tricks you could go to bed. It's not I'm sorry Uh, here we go 5.79. This is the one. I'm not sure what the value is It's got a positive load first I think it makes sense to me. Come on, baby. Yeah, that's good It's good and broken free Try to make it it Nope Man Move sometimes the The parts that easily get stuck on the negative because it's such a large ground plate on some of these Best to lift that pasture leg up. Well, it's molten good angled for your catching thing That's what we're going for right here. Hopefully this still be relatively Easy to work with. There we go There we go I'm gonna set up a little room What are you watching honey? It sounds like you're watching some stupid nineties fart show When like 90 when it was funny to have like fart sound effects just over Like this america's funniest home videos it would be Bob Saget with a voiceover of nonsense All right, back to reality. This is a rubicon 50 volt 100. That's what I was thinking it was and that's what I put in the kit I don't know why I didn't write it on my list here Yeah This one is an 150 rubicon also. So that's a better pasture for sure one more here Right next to a couple of surface mount chips down in this area We'll pull it over Which one is it pitchfond? It's right next to this Oh, yeah, right here. This should be good one because it's got That's big fat compound right there. I'm tiger, baby. I'm tiger We have a loose leg Just gonna be real gentle. Oh my A lot of traffic in this area There we go Oh, happy happy little Happy little capacity These are ones that went on my original list. So I'm just talking myself for the reason 15 17. What is this 15 18? Yes 15 18 15 18 is jammy con 85 degrees 16 volt 47 16 volt 47 15 18 we got it ladies and gentlemen We haven't ever moved Lovely monday. What a lovely monday. Let me get a fresh sip of some water there Got to keep hydrated When decapping something I mean how important is it to keep hydrated? What's the deal with hydration? All right, we're going Right here. I believe this area. Well, there you are, right? Oof. Look at that one. Not a lot of solder on there. Let's see if we can do it. All right. I think it's good There we go Well, are there any Aussies in the house besides Sir Louis? Sir Zez Look at that one pop it right out of there Don't look a little juicy Look at this. This one had to be a little juicy You got some scuzzies right here Yes, everybody given put an F for hydrate H, I don't know H2O for hydrate 250 47 250 volt 4.7. Excuse me right in there. I can also see a little bit Residue there on the board that will have to take a good cleaning Removal, removal of that And we're up to the top One area now of this board that does require some camera funagling funagling here And we will Be Looking to remove Well, we've got a horizontal pulse capacitor Right here we need to remove let's get it out if we can this is another one just Really light on the solder Oh my There we go and fart sound effect in gay Now add laugh track Here we go What does it say? I'm trying to read on the screen 25 volt 100 Micro farad 100 micro farads 25 volts Porectamundo C596 And there's one right under it if the music starts to get off just tell me I can't hear much of it We're ready for lift off folks this one Oh my goodness it almost poked me in the eye awful awful I have to show worse safety glass double checking here 50 volt 10 1504 perfect just when you did of course a hot tub Oh, did somebody solder from a hot tub has anyone ever soldered in a hot tub? I mean, it's the internet. I feel like everything's been done who has I mean, I know like volt are like supposed pictures from the bathtub for twitter But has anybody actually soldered On stream in the bathtub, man, I still don't think anybody would work All right We've gotten those two out of the way next this connection point. Hey koala koa Um, we got to get these four out right here and this four where where my thumb are where my thumb Where my thumb is Photoshop if I was better at Photoshop and had time But I've gotten like no urge to learn that Since my friend Mason, you know, he just takes care of all that for me Uh Since he started doing thumbnails I haven't worried about a photo design very much. Oh, sorry. I'm off-screen. Hey Uh Stupid stupid start with your off-screen Cut somebody We need a rewrite. Okay This is the one I just removed. Sorry about that folks It's the This is a 160 volts 2.2 So I was wondering if this was going to be a 2.2 Because it was on my list as a 2.2 See 584 and that's exactly what it is. I actually don't have This capacitor. I have a 250 volt 2.2, but that will work also But yeah It's one of the capacitors that can go bad and cause that rgp line You can use a 161 uf instead of 2.2 Just gotta make sure whatever you put in there that's 105 degree Temperature rated going up. Oh, yes. See oh This one's definitely lost Lost some fluid right in here And it's even dried up But this whole plate It's hilarious here. It's just coated with electrolyte fluid Better focus baby. Try to focus. There you go. Can you see it? See 584. See all that crust That ring double ring of crust It's especially pronounced on the right hand side of your spring folks And that is what we call dried up electrolytic fluid There's some doubt of the leak from the bottom of this disgusting 160 volt capacitor See oh, yes Yes, look at the crust here. We have we have massive crust here and that's why That's why there was a lot of issues with deflection And one of the reasons why Got another one right next to it and it would be awesome to see if it's blown up to Okay Right next door We have 572 waiting to remove it So we'll remove 572 All right, 572 wiggly loose here Uh You don't have to recap every one of these these are all Capacitors they're known to fail and they do directly impact your screen quality a lot of this stuff on here is extra stuff that No, some of them are never going to fail I mean these fit these will fail three times before some of these other capacitors in these other zones that aren't as hot So you don't have to change all of them spread this board has goodness gracious Hundreds of capacitors on it you could go around with a meter and check on them All if you really wanted to in any that red suspicious you could change out you'd probably find a few maybe one out of 10 or something one out of 15 All right, got a 160 volt 4.7 C 572 that's correct. I don't think this one's as crusty Doesn't look as bad. We'll take a look in a second because i'm gonna go ahead and remove There's two more Caps next to it that I need to remove right up here where my fingers pointing Towards the left hand side of the screen And i'm just going to try to get both of these out before I actually move on and look at the back side Let's see This done with some wiggling going on there Okay, so we have a wiggly 588. Let's just go ahead and undo 590 while we're here piggyback off some of that heat that we generated We've been 588 gosh keep going you gotta wait to see if it pulls down if it re sticks to the side of the air or something I'm gonna pull these Here we go Again, I almost poked myself in the eye. Keep the finger on top of this one That was five This is a 50 volt 2.2. This one's known to fail. That's 590 I believe. Yeah, 590 2.2 50 volt the other was a 50 volt 10 It's all the way over there. Let me go grab it get flying objects Flying capacitors man Literally put an eye put your eye out. Yeah Okay There we go Here we are Exactly run away cap I'm gonna bunch of Basset fuzz here 50 volt 10. Trust me. It's a nice cap though The other one's a Rubicon. Is there a last cluster right here? Right here this fork Very vital replace these and actually Oh, I can't tell this one might just have bad solder on it too Bad solder Tell me what you got This is 522 it's definitely expunged 16 volt 1000 16 volt 1,000 that um That's one of those ones where it could be Two values could be one or the other. Well, we have this one Okay, have a little bit longer To let or work 16 volt 1000 This one's really got Not much solder at all. I'm gonna have to discover these solder this one Let's try this other one now. That one looks pretty rough, too The light on the sauce, you know that one's good Flip your fingers A little step Okay, we got Yeah, another one out We got 206 Which is supposed to be a 25 volt 100 it is it's a Rubicon right here 25 volt 100 Now we'll get out 25 volt 100 right here Get this last two capacitors all the way up Now we got that one of all right here This should be another 25 volt 100 Rubicon and it is The folks just checking out the integrity of these holes Go up here put a little flat fresh Fresh glaze up here on this donut See if we can't get this out last Pociture and we got it out it is 25 volts each one So I'm gonna try to straighten the camera up here for you a little bit Oh, yeah, koala is already on the patreon. It says thanks for trying to Sit down there and get some new members, but yeah, he's actually I've got a message I've got to get back with him about working on something I saw you sent a message. I'm sorry. I've just been Trying to Get certain things done and I haven't had the time To get all the scheduling and everything ready for this week I really wanted to test this stream out see if it even worked this week so All right, that's a 25 Oh Rubicon man, those things are slipping right out of my fingers So that should be all the desoldering we need to do Okay, so there's our caps. We've got them all removed I went ahead of time And Made the cap kit to save some time and move that out of the way and We're gonna install the new capacitors, which I have in a lovely little case right here There we go, drive me crazy. I wonder why it's been crooked the whole time Give me a little bit more room to move around It's my elbow bracelet down so Before I do that clean these pads a little bit Because we all saw how nasty they looked specifically some of them I'm just gonna use this little Pad here Fill a bit of alcohol on it Put down in here and it's gonna you know scrub those spots to start You know this little bit has to do off here There's four there I want to get this section in this section. There's definitely stuff there Let's say it's all oops Let's say that it's all Actually Blewed from capacitors. There's definitely leftover saw Bucks who's left over There's some leftover ooze Because we saw the picture the quality was awful before Over here at these two and this one This is what I'm talking about right Good and clean given the old probe treatment, you know, don't watch plenty of x-files right probe a couple of these This is so wonderful. These I just love a good clean hole Friday yet. Oh, sorry. No, it's just Monday This is Monday afternoon, right? All right Maybe Friday, maybe Monday Early or later for you wherever you're feeling from today. I appreciate you being here with me Checking out I need to clean this area I think checking out might be the most Accurate thing I said These sami days checked out I'm working on it. We're working on it. There we go Something nice to stuff Careful here goodness. What do I do? There we go I was gonna get him clean All right, here we go. There we go Man everything's cleaned up every one of them means we're ready to Go ahead and install things And I'll be honest with you. The the holes look great Shouldn't be any issues with these holes I'm just thinking here and these You see there's still stuff on here. Isn't that crazy? Even from Sunnys factory, there's always residue left on things There's also like a film layer Make sure you don't knock anything off All right, we're looking good a little ESD brushing Good stuff Give her give her the old blows All right If you'll need that for a minute Now I'm glad people are still liking the music. Thank you koala We're gonna start Don't need too much stuff around us So I've got to start installing our capacitors Right over here in the center of your screen is the areas And here's our capacitor kit, so I'll go through and I'll stick some Sodrum or yeah weld them in solder them in And then we will Repeat the process So let's start with our More difficult area over in this area Over the board right in the center Let's go ahead and so first off we have The 50 volt 100 Just a big one People fit in here. This is c 579. Just double check in before I install it We're going for it. I'm looking. I just want to make sure I'm I'm aiming these the right direction. This is the way. This is the orientation There we go And then 1518 16 volt 47 which I have a 25 volt 47 So we're going to upgrade it to a 25 volt 47 And I'm going to go ahead and get these both stuck in here at the same time Oh, I don't have to mess with this zone Ever again Hopefully correctly here There we go Two new caps are in there. Let me show you I'm not done anything yet. So You're not missing anything Here's our legs 700 degrees Celsius. We're coming in here And I'm just going to get a little tacky Straighten it. It's not our permanent weld. We're just doing it like that for right So yeah, I'll show my hand. Let's give it a picture There you go. That's that'll be better Okay good now Let's take the time to do so We got a we got a surface map on it right here I can go this way a bunch of stuff around the outside I'm going to hear with some flush cutters Which fit all the legs Now just remember It's always best to come in here and wreath Do this or do the solder on the leg of the component The leg that you haven't soldered because if I did the leg I've already soldered accidentally and tried to reflow it first I'd uh, but we'd lose the part. It would probably slip right out There we go. Got a good weld. We'll let that cool for a second come in here It's a good solid weld Right there In a squire. Yes challenge There we go, and that's how Without damaging anything like that's it just come in there and then clean it off later Thanks vectrix Have a good rest coming We'll see you in the next one All right Good. Everything's looking good. Just come on over here and check everything out on the other side Good. Good. Good. We're gonna go ahead now and hit up that 529er C529 The 50 volt 0.47 capacitor That So that's something that's more valuable than a pvm you think. All right, that's installed 50 volt one 50 volt one What's the number we're at 529 we got five 23 above it, which is the 50 volt one Where's the 50 volt four seven? Make sure we're sending them all in one new correct direction This should be the 2.2. This should be the 4.7 5.1 is uh c 5.1 it's good to go 4.7 perfect. Oh tissue there right there That's drama I'm expecting that to happen You're you're the legit if it focuses here. I just want you to know you're getting to see this Actually a closer view than I can see it. So if it's working there we go There we have some more Components that I'm going to come in here and put a little tack weld on wonderful too Sorry There it is It's pushing against the wrong thing here. I'm not using lead free solder stiffen I Do not use lead free solder I use low temperature rosin core solder Was it just the right touch of web? Just the perfect The good old days Just remember Diets all there I'll show you the reel here in a second. It's on a reel. I'd tell you the exact thing But I will show you here That's more garbage Just spend a day answering the silly No, good Telling marketers that call me. I love calling Mondays That's their ability to reel. The reason they call me is I have Technically The business number For the business There we go all three all three of those look wonderful Yeah, 700 7 to 750 Celsius on my iron this top part like the weld Top side down here The real show and that's really the toughest area to deal with of those five passives, right? So you can change this five out. I'm all good solder Solder how does he pronounce it? solder Right solder solder solder There we go Bada bing bada boom Bring the tap on it. All right We are moving on Let's This one right here. We got one right here. We got four here. We got four here and two here So we probably should just work our way this way or out from like here this direction Oh, so yeah, see so our F. Sorry 700 degrees F. Yeah, let's see I'd be melting the melting the walls my skin included Yeah, that's live that's live shows for you buddy All right, we're going for it. We're gonna need five seven two and five eight four We're gonna need five seven two and five eight four to report for doing 164.7 Got that one it's this one to 54.7 Where's the 252.2? And That's the one Yes, 105 degree nishikon 250 2.2, so we're gonna do a little upgrade here. There's a much better much better Much better faster. We're going for the temperature of whatever mercury Venus maybe Actually, yes, remember in the right direction because You don't want to put one in backwards Look how I made this comparison comparing things. These are so much smaller The ones that were That better rated shows you what It's not even that much of a technological change for something All right, I'm gonna get that bent over Those caps got legs and they know how to use them walking down the street Fix and save the crt's The next Reminds me that I watched recently the Glenn Gary Glenn Ross. I think it's on youtube where I live for free right now great It's a great movie you can appreciate when you get over I guess fabulous Stuff you gotta always be closing. That's what I remember You know First place is a new Cadillac second place The set of steak knives You know what third place is Third place is you're fired lots of rain That movie too The rain is pouring You know Hey, you're uh, thank you for coming in pillow wacker. Well at the temperature of the sun folks 700 degrees Celsius Got two more spots next to those capacitors For a couple smaller ones you get those out of the way Is done That's 588 and 590 50 volt 10 and a 50 volt 2.2 For 590 my legs are twisted That's what the caps mean My legs are twisted I think it's good Yeah, man Come on. Give me some good legs here. It's into the holes Is this The correct course of action Is the answer always just recap it comes to cr2 repair just recap it it'll fix it It'll fix everything Is more needed than just a simple cap We shall all find out Shall all find out I'm asking a lot Got two right here one over here that I need to install. Oh goodness here we go We're going to take both those legs man That's edge That's here a little bigger There we go Hopefully we can Zazz. I don't know when uh, see this system. See what your job. What's your new uh Career business How's going on get back to an episode Of the cathode rate broadcast spent a while goodness Longest break probably ever All right, there's that one 1504 To our next capacitor and that is 50 volt 10. Yes Just right below this connection point right here and then 596 should be a 25 volt 100. Yep. Okay There's right above it use my third arms here. Did we change it up to some synth? Oh now looks like it's still some jazz stuff here was sometimes I do Use that. Um, I found some pretty good generic 80s style music for videos. I used it in the last one I even got to use it. I got to use a metal metal like song In the last episodes Of course, it wasn't a long segment So that's a good question Stefan or Stefan it is Oh, it's very dependent. You're I've I've used them. Uh, I used to use them I have a lot of old videos where I used soundtracks from video games and I feel like we're flirting with disaster Doing that at least from my perspective now Back in the day, I used to love doing it And but I've heard of people getting You know, I think you're just inviting copyright problems down the road by continuing to use it I just deal with trying to find stuff that's new um that is available for me to just license which what I use now is a A program called epidemic sound I know it would be cool if I could just play some good old Music, I know it's like It's probably harmless if I did it honestly, but You never know We're talking about Nintendo. I don't know why they've never gotten on anybody's case about it Excuse me I'm not saying I'm not trying to give them any ideas. I'm sure if they wanted to they would do it That's great. This is all going great. We've got everything installed except our final four right here We're gonna start with the two insiders, which is the 507 and the 595 the 595 is This 25 volt 220 595 and then the 597 right next to that and just like that We're ready to weld these two in Just things it's like I just accept the fact When it comes to music to just deal with what I can find um Like I said, and it's it's I mean, I think it's 16 dollars. I pay 15 or 16 dollars every month for it And just to have the peace of mind Is good Once you have a channel that you know, I mean my channel isn't huge by any means, but it's a good size to It's got some value to it. It's good to preserve that and you don't want to You know just do it as part of Part of kind of like the cost of running the channel And it's pretty low cost like I like I said It's one of the lower cost things that I have is The music because there's tons of things there's even Like I use a lot of sound effects off that site And that means if if anybody I mean I've had I've tried other things too. This I had some videos that did pretty good Within the last year and I used classical music on them And I went to find over, you know 100 years technical they were supposed to be over 100 year old recordings Anyway, that didn't matter Because eventually somebody claimed like Mozart Stuff said it was theirs So I just said forget it. I'll just use this because then there's no question like Even if what if somebody comes along just false copyrights you for For using that music from a video game and they don't even own the copyright But what's your complaint, right? What's your how do you like? How do you fight that you have no way to fight it because you don't technically on the license the music yourself either That's what I thought so I just thought you know next time if this happens I'm gonna have the music key kind of All right, we get 206 and then the big one which is the 522 which is 16 volt Well, that's actually on there now 16 volt 1000 I've only got a 25 volt 1000 here So we'll do a little upgrade. We still got well, see like I said that we still got three more caps on the side That's why I'm still got caps on the cap kit And I'm gonna have to find one more kit that I was late on apart That one's gonna be a tight fit right there That's okay And then this one one stone It had to be you Oh, yeah Your scan lines took my breath away I have no idea how these songs even go kind of I can I can I've got the headphones around my neck so I can hear a little bit like the Horn a lot of this is stuff. I've not heard before it's the jazzy playlist We're soldering capacitors. Yeah. Yeah. Yeah We got some push cutters now And we're gonna go back and reflow the solder And make those welds look Classy and sophisticated I doubt there's like I probably ran everybody off from the Stream today. Thank you. Thank you very much. If you uh Like or hate my music you can leave a thumbs up or thumbs down. I don't care It's that terrible leaves the thumbs down and I'll Probably never seen never sing again Probably all right Looking good. We've got Just Three more right Here we've got a 517 1517 and a 508 1517 It's not 508. That's five seven something It's a 50 volt 10 and a 25 volt 100 And a 16 volt 1000. Oh, I just put that 16 volt dog on it I put that one in I put I meant to put the 25 over here What's minor threat Well hot dog. Where are we at? We're at five seven seven. I want to make sure I'm getting the right one here. Sorry folks 50 volt 10. Yes 1517 is a 25 volt 100 Put in that one And then I'm gonna have to go hunt down another Faster Yeah, yeah, here we go Wonderful Boy, these are all close together. Let me see Here we go. I don't know about minor threats, but I know a major threat to longevity of CRTs happens to be at this Topic we were mentioning earlier, which is the lead-free solder It just doesn't have the kind of longevity Durability, etc quality that Lead leaded solder has the lead free is not not as good If it was as good then nobody would Nobody would use leaded solder We got to get one more capacitor here to go right here Right there. Here we go Got one right here This is awesome This is awesome. It's been a while since I've been able to go through and actually finish a recap Um On the stream My last one Well, let's hope it's our last one We'll have to go back after this and check see if I made any mistakes Because I've been known to make mistakes. Shoot. What was it the last one? I did make a mistake on that board The eight inch pvm I had a capacitor and upside down I do a little more than I normally would on this one, but It's the last one Look at that board Let's have a look here. Let's have a closer look Guys can pretend you're you're the quality control manager today See what you think this is ready for Ready for cleanup We'll run through a couple checks here and just make sure that Everything looks good just cleaning up my stuff a little bit Before we go on any further like I promised if anybody's still here and was asking Let's go switch to this. I'll show you This is the solder I have been using forever. It's got a big reel. I've used almost all of it right there rosin kester Oh, that's one pound Let's read it says 60 40 60 40 0.8 millimeters in diameter 0.31 inches 3.3 percent It's under warranty Believe me or not till 2024. So I've had since 2022 or something. It says Hey, I used to work in quality control All right, let's go back to our desk that desk can keep confusing this. I'll change the name on that Lie back I am also going to look at the other parts just to make sure everything looks good I've looked at it before but I like to look at it again and I don't want to have anything that's pre-existing touching Like another component to short out possibly sometimes you'll notice things like that Um, I'll show you a good example of how this can happen Here in a second, but especially over in these areas I look over here These two these legs, I mean, I don't know These legs can easily bridge out and touch if they get bent on this diode and this resistor And that probably would cause a short that may damage the crt I have no idea the board or other things on the board But everything looks good over there. Let's look at our caps that we installed One two three four Five six seven eight Ten eleven twelve thirteen fourteen fifteen sixteen seventeen eighteen nineteen That's it. We have 19 capacitors on our list. That's how many we changed And every single one of them Is facing the right direction and then I'll go back here to Check out all the welds. Now this should be cleaned That's where I do a real final check, but we're just looking here Okay, now we're gonna do we're gonna clean this There's the deal I might have to pull this board and clean it again later. I don't know Um, I'm almost out of time, believe it or not So let's see if we can clean a little bit off. I'm not gonna get a little bit of it off So this is without using extra flux. This is just from the solder itself the rosin core flex core solder that's the solder you just saw and You'll definitely get flex residue just from using it just from heating it up. All right See we're getting We're gonna get a amount of that off. Okay, so let's take a little brush Give her a little scrubby scrub. There we go. We're gonna get this We're gonna get a lot of this off pretty much as much. Yeah It's all in the same area So a little bit over here is just it's a little more and there we go Do that again A little bit lower There you go And it's looking good. All right. That's a good cleaning right there. Excuse me. Sorry about that Blow it off a little bit All right, I'm gonna rush all of a sudden. It's let's Move it over And it's good Now there's no guarantee that any of this stuff we did will Actually work unfortunately It's a risky take in the high stakes game most CRT repair Get the chassis back in here Give it a chance to Hey Belmont, thanks for showing up. Hope you're doing good All right. Yes. Yes. Yes Brushes up Let's install these These screws that hold the board to the Guide plate here. All right. Here's one There's a two There's three No front here Am I right next to the fly right on the fly back actually making the Fly back in the frame there right there I think it's looking good. Really. I like to give this thing a little time Before I just power it right up Just in case Anything needs to evaporate I think we'll be okay by the time This guy gets installed I think it should be fine Hey Let's uh See about slipping this Over here Into the back of this We change the camera and show you what I'm looking at right here. It's the back of the CRT Get everything No tally light on this one There's power stuff The back tray here. All right. There we go Let's see Just to add the power supply I might go ahead and put a couple ground screws in here Just because these monitors can Um not power on If you leave off ground screws sometimes So I'll make sure you add them And Just one more thing Well, if you look up in the top, I'm in this corner with you That's everything put back together um So Say a prayer and Let's hope Let's hope this works So I'm going to get a power cable reversed This has a menu on it And uh, we'll see if it pulls up. I want to make sure the button's not pushed in No good All right, so if you remember In yesterday's Or I mean in the in the video I had to use a spare power supply Because the original power supply was dead. It has a dead five-volt rail So this is the replacement power supply Uh, but It's installed It should work But I have no idea I guess right. I mean I have an idea And I'm hopeful Positive attitude, right? So what we're going to do As everything's good we got power and Me let me pet a log and The super nintendo is turned on if we have power there So let's just before we Do too much let's let's power it on and just see what happens. All right. Here we go We're powering on We're powering on It's definitely doesn't sound as Wild as the other one did. All right, there's the new it won't turn on Oh gosh, I don't see anything Oh Yes Okay Here we go. So folks, this is the screen now before we do anything else Let me show you what this looks like the last time we saw this so let's uh I'm going to turn the music off. I'm going to switch over to this desktop view I'm going to minimize that Well, I'll leave it up for now. What I'm going to do is I'm going to go over here and uh Well before I do all that Let me uh, let me just do this. Let me show you again this okay And that at first I'm going to pull this up so it doesn't take a second if you just See that working And before I actually send a signal to it again, this is the very first time it's been powered on um, and I'm going to show you what it looked like before If it'll let me play my own video here And Let's just See If I can get this pulled over here to the section of Video where I show the actual condition of this, okay And then what I'm going to do is yes. I've got it here. Okay So this is what it looks like now Let's go over to this one I'm going to minimize this We're going to play we're going to put this in And I'm just going to look at that And first off we had the red green and blue lines there I'll just check out the distortion on the screen Sorry about the closed caption. I didn't realize that was on but I'll turn that off And Check it out like look how bad this deflection is. This is awful and even after warming up for a second This is what it looked like. You still had the red green and blue lines and I did not change that setting one bit Only thing I changed was a couple of deflection settings But that right there is how it used to look Uh, if you want to see more of this you can check out the uh video And I show it and that's it. So Um Anyway, I hope I didn't close everything out. I don't think I did. I think I just closed out the music Let me go back to the shop There we go. There we go everybody We've got power to it. We didn't even have to do anything really That was all the capacitors will pillow wacker I don't know why I'm calling you pillow wacker. I'm sorry pillow hacker Um Yes, it is it is strong. It is the pvm. So now Um, I'm actually out of time. I have to go I have to go pick up my son from his basketball practice. It ends at 4 p.m Which is 30 minutes from now and it's 20 minutes from here So that's going to end this stream today everybody just for today though Because uh, what i'm going to do is I still have the that's the replacement power supply So I still have to I still have to go in and fix that power supply I want to fix it. I want to fix it. I know we can So we're going to do that and then we'll test this screen out on the next stream tomorrow I'm going to make if as long as this system doesn't crash I will try my best to uh Stream again tomorrow. So if you haven't already make sure you're subscribed Please hit the like on the way out here for me If you want to go back and see this video from the beginning you can see all of this Fixing and also if you want to see the video from this pvm I linked it in the comments here. So you can check that out too I have a fun video there. All right. Thanks again belmont side dragon strong last draconic roll pats pillow hacker Flack you euro Thank you all again for coming in today. I'll see you on the next stream. Have a great day