 There you go check that out like I always say cookies and milk, baby This video is brought to you in part by TrueTech Tools quality tools essential support All right guys, we got some filters there got a metal bracket here, but you might know what that goes to Scrabble all the bags here and let's go over here take a look at what we got to take with us All right, so we've got to change this compressor I found bad last year and they just now decided to get her done Even though it was under warranty. We've got our bracket here and We got our lift here, which is 120 volts will still power up there somewhere. We're gonna lift that up now Yeah, I could probably carry that with a rope or something like that I've got a rope here, but work smarter not harder just so you know I don't sell this if you want to copy it go for it There's not enough money in it to make it worthwhile to make them You know, I'm gonna sell so many of them That's why most people go out of business but to build it yourself. You got some handy skills Which I hope you do if you're doing this Not a big deal get the old handy-dandy Harrier Yeah, that's a couple pounds. All right, let's go ahead and weigh this thing. All right there Yeah, it was 95 pounds to make a little easier. I still people's ideas. I didn't want to pay for Exactly Oh, that's reason why you just set it down. It's too heavy So as long as I got a plug in somewhere nearby, I'll be able to power that thing will be good Yep That'll work perfect As soon as you get this first one on here You won't have to hold on to it much after that. I'll just release this And pull that down to the bottom which I like that a lot better than the Mechanically do it Lock it back in like that As you can see I could make it super tight. It can go back and forth a little bit, but I had to make a wider So it'll fit ladders that have a wider width once it goes that far. It's not going Any further if you wanted to get crank on it or if you wanted to put another hole drilled there On the back side you could do that. Yeah, there we go. That way we get it for next time I've only used this thing a couple times as you can see. I mean we carried it this far. Yeah, but good rope it up You're gonna kill yourself doing it. I mean, it's hard enough. It was bad enough just carrying the thing up here. So I'm gonna do whatever makes it easier on me And it's got a little hook There you go. Go ahead and get this stuff up With the rope in my hook And we got our cordless nav back pump here because this is 480 at this location So that's gonna make it a little easier. I don't have to run extension cord a hundred miles up We go and then we got this all here So we can go ahead and hook it and pull it right up the ladder Okay, the unit we need to work on I believe is over there though. This will be a lot easier Than what it was before with the other one I had There you go Check that out Like I always say Cookies and milk, baby Got a little bit of a discrepancy there on my height But we'll make our way around it. I ain't too worried about it There we go If that was straight up and down like it was originally built for Cool. So if this was a heavy Heavy heavy one like hundred and fifty pounds two hundred pounds You'd be able to Lower it down just like that and it'd be good to go How you like that stuff not bad Like I said, we can take that slack up. This is the first time I've used it on this ladder type of design and it worked just like I wanted We have an eyelet right here. You hook a rope on it And as you noticed it rotates around just like I needed it to Yeah, I would not I want to try to carry that up Up here on the roof Pretty sure it's this one or it's been Last year in August. I think when I found it bad. There we go. Yep. It's this one short of ground 831 22 not bad. I mean like I said, it's just socks that we're just so high up Yeah, it's just we're way too high to be able to lift that from the ground Thing is we're still not as high as what the whole factory is because we've got another Ruff over there. It's even taller yet There's a couple chillers here. I found compressors bad on that I got a Change on that too good and get this thing recovered and They're taking out Yeah, this filters are a little dirty Look at that anything to cut costs man. Anything to cut costs All right before we get too far along make sure this is the right one 460 volt it is a ZPS 83k we have a ZPS 83k CKE CKE tfd Been pretty happy with these crescent side snips and lines man. They've been really good I don't like the jaw pliers as well But That's just the way I don't like the way they hook up with the metal Otherwise, they've been really really a nice Set of cutters if you don't want to spend the money on canypics and you want to get something It's good, but not a million dollars these Crescent K2 series, which is a z5 for 2-8 CG They do a heck of a job and they made a video on some of these other homemade style tools Which you can buy this if you want to pay 45 50 bucks for it What this will end up working out to be in is This is your trip hook and then this is your lift hook, which is all same rope And then when you get down in I've showed us some videos before so if you've seen it once before don't worry about it But go down there you hook it lift it up to lay it down boom release this is going to make it a lot quicker and easier to get my torches and Nitrogen tank and all that crap up here without having to go up and down the ladder 60 times Got it, okay and Up comes the nitrogen didn't have to go down there a lot of less walking Like I said, this is my rope It would have just it just barely reaches that first floor, so I don't know if it would have reached all the way down there or not Get everything recovered get the machine back downstairs Got some of the things off the roof that we don't need now. I'm gonna go ahead and just purge some nitrogen through this thing that way Gonna braze it a clean braze joints last thing we need extra carbon in the system This is a 2020 So it was two years old. I thought it was a brandy startup or something, but it wasn't got a number two But like I said, I like my little micro Rosebud here and it's pretty much about the right capacity for a lot of the medium-sized Pipes, you know up to I think an inch and a half is what it's rated for which obviously I've done two inch with a number two Nice, okay, let's get that second stage thing undone there There we go They put this gas line like right in a great spot here really thought out Yeah, we do have a solenoid Yeah, see it's definitely chucking it out You wonder why it makes a difference that right here is it it's got oil in there I should probably done that ahead of time. Oh, well Okay, there we go. We can move that away a little bit Now when we heat that Back up she'll pop right apart Freaking god These guys freaking jam that thing in there for four foot all falling down there. That's why you always remove your Torch away from it And you pull it apart That's why you're supposed to cut it out also But then you got to splice in another one have a coupling which is next to a fought for to leak. Yeah, I'm good Get the discharge undone There we go, that's a lot better Okay, let's see if we can get this around The power that they wrote How pretty the oil wiped up now because we don't leave that behind Don't be a dirty technician. It leaves your nasty mess behind leaving the next guy wondering do we have a leak? Well, it's really just you made a heck of a mess We're gonna get that filter dryer out of there while we can now usually that's a very last thing after getting the compressor in We're gonna keep on breaking rules here You're supposed to cut it out. Like I said on the compressor Nitrogen rolling again. All right, there we go That are going actually if I Go one leg and goes all the way down it actually hits down there Gotta get that filter that flew over there when I dropped them down there All right, so we got everything back to the truck Got an arrow here want to make sure that it's stamped in there correctly because the sticker could easily put on wrong We're gonna see maybe if we can slide this over top of the current pipe sometimes you can But with that thing out a little bit Yeah, look at that It'd be like like like they're brand new like this horrible thing never happened The little purge through there that's gonna come out through here So we just shoved all the oxygen out and now we can put it down to braze mode I think I might use my other torch tip though. I think that's about as far as it's gonna go down in there That heat just wraps around it pretty pretty nice Here's that way. We're gonna burn a little of a pain off. I'm sorry. There ain't much you can do about that That's just gonna happen. See how she's sucking upwards. There we go Getting her right up in there. Good deal. We pulled out all the way around there You can see where it pulled all the way up all the way up in there at least Good quarter inch or better. Now this will do up to I think an inch, but I don't like been at a bunch It does a nice job Unfortunately true tech tools does not sell this. I wish they did but they don't I will put a link for this down below If you can get it through true tech tools I want you to get it through them if you if they don't offer it Then I have a Amazon link you can go through them I make a couple percentage points off of the Amazon and mainly get the support out of true tech tools and with that torch tip being like that you're getting on getting off very quickly and You know, it's it's hot, but they ain't burning the skin off my fingers, obviously Electricians this way you don't run the wire right across here. See if we can't get this bent Back into place under past a little bit and I like to See if we can Wiggle that turkey in there So let's go ahead and pop that back off Otherwise you got to take the wire loose and walk it around it Hit it from the upper side here where we got Coming from all directions Not getting blinded This other one, I don't know we may just like I said you can open that up To hit it, but at that point you start shooting straight ahead and Sometimes I just don't feel as though that's quite worth it This works awesome for I would say more like half-inch and below you can go bigger, but it's just not Not really that great for it On that base inside There you go, I think I got it looks like we got nice wrap around I don't know. We're gonna get a little something on there and we'll spray it here and we'll see Get this bad boy tapped in there and we should be ready to pull back here in a second so far We're at 156. We'll see if it drops Let's go ahead and valve off and we will spray it Spray and pray. Otherwise, it's gonna shake Shake rattle and roll Give her to the solid Give her a solid looks to me like I must know how to braise got lucky on that one Make sure there's nothing rubbing back here on any of that crap. I'd say let's blast this nitrogen out of here We one thing it's kind of bad about these Max core tools they got you can't I don't have a valve core tool for those that they're stupid money So what I use is a depressor So we got here this thing I'll crank in and That'll press that thing all the way down nice and far and open it up wide open Which is the whole reason why the factory is using them. We'll isolate the And see how that just did that that is why when you close it off to Check your vacuum that sometimes rises real quick So when you close it when you're doing your vacuum, you want to kind of go halfway There's a spot in that ball valve believe it or not that actually gets trapped As always and get the stuff at true tech tools 8% off with discount code Survival that check out off your total order. I've been told there's some exclusions But I've not really seen any that I've ordered off anything I've ordered So more times than not you're getting the better deal there all the time and you support the channel Like this here, it's kinking me a little bit. That's because I've got the right angle tool on there Which I got those not too long ago, and it makes it a lot easier To get into some tight spots, so we'll go ahead and crank this thing down And that'll press that valve core all the way down on the Cormax And then we have the valve Poor tool there isolating it so that when we want to recharge it. We can charge it. We got the blue vac pro which in my opinion is one of the best vacuum gauges Period bar none nothing better. I Have the blue one that I started with over ten years ago, and it's still going good had some problems got all the factory They fixed it for just a small fee I mean we're talking Like 50 bucks. I mean holy crap. I mean that's a $250 or $300 Ordeal and then while we're advertising for all the great companies out there. We got NavVac Awesome for CFM pump. This one's a little more money than the two But you know I've got an extra battery or two now. I got the new batteries Which have the green LED light on it and a USB? Got these in April Makes it so much easier. We're gonna go ahead and get this thing done off one hose just to kind of see how long It takes to do it because honestly, I was never a big one hose battery went dead on the GoPro. Let's go ahead and turn this We'll see how long this thing takes To make sure that gas balance is open She's gonna pull a lot of refrigerant. Oh, yeah, you can see this oil looking shoddy That oil is looking a little shoddy You can see that she's already starting to drop on the lines there She's moving along. Well, we're waiting on that. Let's go ahead and get this belt change that was one other thing that I Had him quote doing while we were here good time to highlight I think I did a short on this one. This is the viper Brazing pad they got which is pretty kick-ass. It's got the little cut there It's a lot cheaper than the other one that's out there that you've seen. I could have been showing that one off, but Vipers came through Provided it for me to try out and try it and see how I like it and so far I've been real happy with it. It don't have any of that weird, you know fiberglassy feel to it or anything like that I've been running it wet because I braised it's gonna give it longer life Don't want to braise on that. That's a sticker. It will melt it from what I've heard from other people It's been doing great. I Been happy with it so far. I always love Viper products. These guys are great. I won't leave this extra this old one here because it's better than none at all It's middle of winter and it breaks Last thing I want Let's not have a belt. You never know what you're gonna need So we're gonna have to loosen that up. You don't want to roll the belt on. You will break the bands inside the belt Obviously this one here is pretty dang tight Now Tori's got one back here hidden Then you got proof. Yeah, I changed that thing. Look at that. I got it all on my hands. That's fantastic I started at 52 after and we're at 03 after so we're at 11 minutes And we're already 1100 and 18 microns so we can shut that gas ballast See if that speeds it up a little bit. I heard a change in pitch a little bit. That oil needs to change some fears We are just about there again a little closer than we were earlier. So we're at 800 won't be long All right, and finally test-o test has been really good to me, too They actually talked to me and take care of me. So you got a support test. Oh, they're good stuff I've always liked test-o's manifolds because they were small and they don't take up a lot of room. I Don't like a small spaceship on my unit kind of gets in my way I'm trying to work on it So we just found off we're watching so it kind of rise we get on it we're going to Get this thing filled up as long as it stays where she needs to be at and Get her going. I can't see that their crop crop dust in there Yellow plane over there All right, she's holding there. I'm happy with that. So let's get this thing juiced up We're gonna break this vacuum on the suction side once we get out of the vacuum We'll go ahead and then start dumping it on the liquid side and kind of start going from there and I love the fact that I can sit there and Add the refrigerant to my unit. I could go grab my solenoid valve which is kicks and Wait right in there do super heat let us discharge itself Now like I said, I can't put my high-side gauge on there yet because we're in a vacuum last thing I want to do is suck in air Now you can remove your Yeah, remove your Blueback Like always blueback doesn't care about pressurization. I think they're good for well over 500 And I never have problems with it getting oily and if it does get oily You just it'll tell you that it's oily and then you can clean that sensor I use a little bit of spray cleaner that's made for cordless tools cordless air tools and That's the easiest way I had so many problems back in the day with Micron gauges back in the day and you know it just that's why I never used them I had problems with quite a few different ones and That's why I quit using them the resolution on the blueback. It sits there and shows you Immediately that you know, hey, we're going way up or going way down. Whatever no special handling I mean, obviously you got to treat it right, but it just did a great job See this would be a great example where I should have used the solenoid and I did this on the last video Where I did show it being used I could have walked away from this started taking things down to the truck and Unfortunately, actually I have it up here darn it. Yeah, solenoid So yeah, I could have just turned that thing on and boom I had it Walked away, but we're about nine pounds now. So we'll just go ahead and hold off on that We sleep for another day. I don't know how long this is gonna take to kick on or if it'll even kick on Cuz I don't know if this even does an area. That's all that important So let's see if we can make this thing run with a Okay, so I went down there and tried to find the thermostat Well, there's multiple layers and these can go for the floor underneath me or they could be the floor all the way below me and Some of these like you see this one right here Side by side might be forever to Coons Age before you finally find it So what we got going on here We went over by two tenths of a pound We're kind of just Want to watch it. We're at 33 degree evaporators And we'll see how this goes so far. We're looking good super heat 1716 So I think we're gonna be fine. I heard the solenoid click I went ahead got the extra jumper on there and she's doing About what I anticipated I don't know what the outdoor temperature is. I think it's because we are running 57 degrees 57 degrees. So 6777 we're 51 degrees over ambient Not bad Running a 15 degree super heat now and an 11 degree sub cooling Everything's looking pretty good from what I'm seeing right now. So we're gonna let this run for a little bit And we hopefully we'll be able to wrap this thing up because my time's up All right, it's holding in there really good. So we're dumping everything back into from the hose and back into the unit Superheats up there respectable levels of coolness too That's the only thing we got to do. All right guys, that's gonna wrap this one up Hopefully enjoyed the video just another day another dollar. So anyhow, if you enjoyed the video, give it a thumbs up Consider subscribing. We'll catch you on the next one later