 Hey guys, shea bear one thousand here today. We're going to be Troubleshooting this old TV set Stay tuned. I'll show you how to do that Excuse me What we've got here today little project This is You see that This is a Mitsubishi. I think she said it was a 55 inch I Got this route down here I think she said it's 55 inch. I haven't measured it, but It's a 2006 from what I'm coming up with so it's an older one It is the LCD But it is also it has a lamp in the back of it Now they couldn't figure out what was wrong with it So she got a new TV and said if I wanted this one You know take it off her hands throw it away fix it whatever I can have it So we got we went and got it today. This belongs to one of her patients See the model number is Say the model number is WD Dash five two five three one I had to take this in my phone. So, you know So I wouldn't forget to show you guys this now What what she's claiming is it'll come on for a second and Then go off Shut off now. Oh, sorry guys I had a Craig one time Well, it was a 55 inch, but it was flat screen. It was never it's like 2012 and Yeah, it was only a year or two old when this happened It was doing that what I found out inside of it was the capacitors in the power board now There's a lot that can be wrong with these things but they're actually pretty simple if they're capacitors You can either get another motherboard or another power board or wherever the capacitors at But you might only have to have one capacitor and you can pay some money for a motherboard Or or I shouldn't say circuit board your circuit board Or if you know how to solder you can order the capacitors they're printed bright on it right on the capacitor of what they are and You can order them. It's just too little too little prongs. They're going to hold you on side of the old one Stick the prongs through the hole solder the new one in clip your ends off They're real simple if you know how to do things like this now Like I said this one she said She was using it One night and she shut it off the next day she went to turn it on it would come on But she said there was sound but no picture and then it would shut off So that could be a capacitor, but I do know on this TV here. I haven't researched it yet But I do know you can run a code on this on this television say here Now I don't have the remote control, but you don't have to have the remote control on this Mitsubishi To run the code you use the buttons up front here, and I will show you how to do that Once we plug it in and see what's going on. I have not plugged it in yet So we're going to find out this together. So let's do that and see what happens here Now what we're how we're going to do this is I'll explain it to you real quick. There's two buttons on here one is the is the menu button and and One is the input button You hold them together you hold them in for at least five seconds and your LED light over here will start blinking like if it blinks Say two times Pauses then blinks three. That's a code 23 now It'll do that five times so you're not thinking it you missed it and it was 32 it'll do it in sequence at least five times So you can get the right the right code now. I I did bring up the codes on my phone right here. I Did bring up some codes for this thing so And also it tells you how to how to check that if you have one of these old things I'm just making a video, you know I mean I don't know who would and I don't know what it would cost to fix it if it's a capacitor if it's you know something else So I I don't know. Let's just see what happens. It was free and so it was a video So let's let's see what's going on here. Let's go ahead and plug this in Which one do You plug this in I heard a click now this one has a fan in it And it just kicked on We got a blink of light down here. We'll bring you a little closer Zoom in on that maybe Can't see that Yeah, see that light there. Now. That's a light. We're gonna use to trouble troubleshoot this side the codes on this thing Now what I'm gonna do. Okay now It did its thing and what we're gonna do Is we're gonna turn this on and see what happens right here's the power button see the power came on See what if anything happens the fan kicked on slow down a little crackle in the speakers there Okay, I just heard another click Okay, now it went off now. There is a reset button Right here is a reset button Get you down here. I'm turning the light on here. See if that will help There is a reset button whoops right there Right there is the reset button. Okay now We're not going to hit that reset button and I'll tell you why because The way this is acting like if it came on for a couple minutes had picture and sound and that kind of thing and Then went off. I would try to reset it But this nothing really happened up here. I could hear the inner workings. I could hear the fan I could hear a click in the relays and whatnot that's in there I don't know if that's what they're they're called on a car or they're called relays, but on here I'm not sure. I'm not a TV repairman guy, but I like to try to fix things myself So I'm not going to try to hit the reset button. I figure I'm wasting my time so what we're going to do is We're just going to go ahead and run a code because you think about it if If it was a simple fix like a reset button It's going to keep doing it more and more so Even if that fixed it it's going to do it again and you should run the codes anyway if it's possible of doing it I do know this TV for a fact is You get it will give you a code now. Let me get you zoomed in here on the light and On the buttons now over here. I'm going to try to get over here out of your way, but right here. Whoops Okay We're going to be holding this button here. That's the input button And skip one. That's your guide. This is your menu. These are the two buttons We're going to be holding don't push anything else yet, and we're going to watch this light. Okay We're going to watch this light right Right here. Okay. It's a timer light. That's your green LED. So let me get on this side Okay, and You got to hold it for five seconds So Watch for the light and it'll start blinking a code. All right. Let's see menu and input They're both pushed one two three Four five there we go One two three four five six One two three four five six One two three four five six One two three four five six Okay, so it's flashing a code 66 All right Let's see what that code is on our handy-dandy little Troubleshooting guide here. All right. All right. Here's the code. You scroll down to this. Let me back this out of here Okay quit it'll do it like I said at least five times So let's see what we got here. Let's see if I can do this for you All right All right, see there's a code 12 Code 12 no error code 21 22 22 23 32 33 34 there's 35 36 37 42 45 and 55 there's 38 39. There's a code 61 and a code 66 now we got a code 66 Now it says lamp did not start. That's DLP TVs. That's What this is now It says bad lamp or ballast Okay, so what we're going to do is I'm gonna turn this TV around for you and I'm gonna turn this TV around for you And I'm gonna show you how to check that bulb if those codes are right now I have had codes just like on a car. We call them phantom codes I What was it wasn't a Craig might have been a Samsung TV? Don't don't mark me on that because I'm not positive that I ran a code on and it kept coming up this weird code It didn't exist. It didn't exist Well come find out the mother the motherboard or circuit board whatever the main There's little chips in there one of the main chips was bad and it was sending an error code So what I found out later when it throws a phantom code It's just like a car when it throws a phantom code like that It's actually the computer modules inside of it the electronics That tell you what's wrong with your lamps or whatever It's actually telling you look I'm bad. You got to get rid of me So it will actually tell you if it's going bad or not So let me get this turned around for you. I think I can do this. I set it up there by myself You know what? I'm gonna keep you guys rolling in case funny stuff starts happening this thing in a ways like I Don't like 70 pounds or something. So I set it up here by myself, but monkey helped me carry it in So let's unplug it Let's see if I can spin this around Without breaking something like my camera Break the TV worse for my back. Here we go guys Like I said, I don't know anything about this It has not been a port But I do know one thing TVs take a Phillips head screwdriver So I do have that handy because I knew I was gonna need that and it did come up the code 66 on the Now Bring you over here Set you down here now on the back here. Look on your back. Make like said make sure it's unplugged and on the back If you have the DLP TV set Somewhere around it There's gonna be a square a Square cover That's gonna have a lamp inside of it. Okay And it'll tell you why All right. Now this one says lamp cartridge access panel Always unplug this TV and be careful if you take one of these apart There are capacitors and stuff in there that do store energy for a long time It can give you a shock the older TVs remember the tube TVs that's TV tube itself on the back of it I used to do it for fun when I was younger before we had YouTube and before cameras was all over the place You know, I'd get them just to show people and I would take a screwdriver or something or get in there But these aren't too bad, but still be careful in there and besides you don't want to ruin anything else if this is your problem So let's get you brought in here a little bit closer All right now down at the bottom of this one yours may vary But if you got a lamp in your TV there, you know, it's all pretty much the same Just look for the access panel for your lamp. All right now here and there's always an arrow down here Let me see if I can get you that arrow All right There's always an arrow that that will point to the screw All right, I don't know if you can see that there's a little arrow right there That is pointing to that screw and there's one over here on the other side And it's like that all the way around the TV if you want to take the back off There'll be arrows pointing to the screws that you take out if there's no arrow on a screw See all these screws up here and here they've all here. There's a good good example here. I do believe Let's say Yeah, see that little arrow right there It's pointing to the screw If you're taking these things apart See that little arrow names it If if this screw would not have an arrow on it, it does not have to come out to disassemble it that means Once you get it apart, you know There'll be arrows on other screws that you have to take apart depending on what you're working on So keep that in mind. It's kind of handy But like I said, I've I've replaced bulbs before so this is really nothing. I didn't have to google this A lot of times I still have to my first My first line of defense is google and I know and the reason why is I know that google always has The closest thing that you're looking for on your For youtube there'll usually be one of the first one or two things that'll have some youtube videos And that's the closest thing and if you type it in on youtube it might come up You know it might take you a little longer, but so youtube has helped me out on a lot of things now I took them two screws out. There's no more screws around here So we're going to lift this out of here and there's two tabs up on top to go one there one there when you go Now here is your lamp now. There's mercury in this lamp So don't Look monkey's pulling in sir She went to store Okay, so All right, listen guys, there's mercury and there's a big sticker here. There is mercury in these so be careful Don't try to break it or anything now on this one. Like you see yours may vary But this one has two screws on it. I've seen that since I pulled the back off of it. I wasn't sure But most of them do there's one right there and one right there now. What you're going to want to do is loosen it All right, there you go and I see that will not come out so you can't lose It won't come out same way with the top one Loosen it Now there's a handle right here this handle I'm going to back you out a little bit pull And it should come right out and there is your lamp Let's see what we've got here. Oh my okay. Do you guys see that in there? The bulb the lamp is is burned out. See all that glass So that is probably the issue with this television set That is what's happened to that The bulb has burnt blown out. I mean actually blown out that is glass down in there See it the bulb so It comes from way deep inside there you can't fix these guys you have to get new ones And in order to to replace this I will show you how to take this apart. There's there's a there's a clip right here There's a there's a clip right here, which is tape Okay, that is for warranty. So I know that Because if if you had a problem with this when it was new and you thought it was a bulb and replaced the bulb That's one of the first things it will check see if that tape's on there if that tape ain't on there They're going to know you try to fix it yourself and avoid your warranty um So but there's also like a little veil Right here a bail whatever you want to call it all right What you got to do if you bring it back a little bit Push in on it there And bring it back a little bit Okay, now this there's a little nut there you're going to have to take off So I can't see this very well there we go a little nut here you want to take off all right so There sometimes if you just push down on that wire right there It'll loosen that nut up enough for you but make sure when you put these back on Now I don't have a ball for this but when you put these back on uh, don't Don't make them super tight because You break the new ball Grab a pair of pliers here. Let's loose first of all let's loosen this wire up here Or this nut All right, then the nut will just come right off. I think it's good in there Just like that Take that wire off so you don't break it There you go This we've got to get these uh these clips off of here Just pry that off I'm just going to use this Careful not to get glass all over you My light just shut off it must be dead I'm sorry about that. See there's one clip We can pull the tape off. There's no warranty left on this thing anyhow, so And then the same way I'm just going to Pop this clip out of here Try not to let a good flinging across the room Just like that. Okay There's also a screw here you can take out, but I really hate to do that Because it also holds that plug in That plug in it holds the plug in not the plug in It will come out all right Now There's this And then you're you're going to have your ground. That's a ground take your ground off I'm afraid of getting them mixed up Put a piece of tape on one mark it whatever you got to do In this case, I know which one it is I won't pull this one out here And I'm going to put it in Over that little thing. Now that's the ground I did that so I know that's metal. It's okay. It's all right It's a ground. So I know that's the ground And this one Is the hot wire you can also Mark these put a little dab of paint like a white dab of marking or something on there So you know that's the hot So there you go now on these I don't know if the camera can pick that up but there's some writing on here And that'll that'll give you your Your Numbers and everything Is it 10 dash ior from what i'm seeing? Yeah Yes, there's some letters there It's a hs Uh looks like 130 hs 130 a which is an amp r 1 0 dash 1 r. That's the number. I will order this Order this bulb through that's or this lamp So but unfortunately, I don't have one guys. This is just uh Like I said this this video is just a uh troubleshooting video. So I uh I wanted to share that with you and you know do it together so So there we go guys now that's what So that's that's how you troubleshoot one of these order ones There's a lot of difference in the new ones. I know hardly anything about I know a little bit Not much but I do know something about these so that's the problem with that one So stay tuned for part two all when I order the The bulb and get it in we'll unbox the bulb together and we'll put it back in together and see if this Old beast will still work again. So that means said thanks guys. Have a great weekend Remember holidays coming up. So be careful and be nice to one another. All right guys So remember to check out monkey 1000 channel and I'm out for now. Shea bear the met the man a legend I'm gone. Shea bear for president. All right guys. Let's do this. See you guys later. Bye. Bye