 Alright guys we are heading to a walk-in freezer that's leaking water so we're gonna go see what we got going on. I've been here a few times before for some of the reaching coolers and some of their other appliances and things like that so if you want to go along for the ride hop in let's go. Alright so looking at it I think it just came out of a deep roster just turned on one or the other. The heat tape seems to be working pretty good. It looks like we probably usually will run our grain line heater through the middle of that and we'll put that 45 or whatever right there or a 90 but they ran this heat tape which is not the stuff we use and it does feel like it's working. I have a feeling since it's nice and hot it's insulated fairly okay but I can feel some water down here that is probably not draining very well. The coil don't look too bad and the reason why that ice is on the line set there is it's not very thick so I'm gonna go outside and see if there's anything coming out on the other side here. This ain't very good either look at this door closer don't work so I bent the kahoonies out of it. See if I can bend it up a little bit so it'll open up really just need a new one. Okay so the freezer is out here along with the cooler kind of hanging there on the wall like normal so pretty sure that should be the very last one so it should be this one right here which is all busted to hell. I have this feeling that the grain isn't working for diddly squat and it probably is freezing up out here on the end. I'm gonna go back in there and see if we can get that to come on through the wall. I bet you anything we cut that at the top it's probably where the issue is at plus don't think it has a trap on the inside so we'll get that chopped up see if we can get that fixed. Alright so we just tried blowing it out and it went right through no problem so we got that chopped off it'll be fine ain't gonna hurt nothing. I'm going to go back in there see what else we can find going on here. Alright so we went ahead and just ran a full bowl there of water through it put it back into a defrost I filled the 45 there with the silicone I'm wondering if he's not getting dripping off of these lines here which I don't have enough of the thicker insulation we normally use on freezer. I don't have any of that on my truck not enough but I'm gonna check with the guy that owns it and see what he has to say. Also the defrost set for 35 minutes which ain't out of line I'm kind of testing to see if the defrost termination kicks out and kind of see they had a little bit of ice built up in there so I'm gonna check with him on that see what happens I'll watch this for a little bit here to see what goes on but you can tell it probably leaked from here because you can see there's some ice sequels here on it so obviously it's most likely where it came from. We've assumed that the defrost termination is working correctly just because we don't have much frost built up on the roof or the ceiling it usually if it sticks in defrost too long it'll sit there and put off so much heat that it will condensate and then freeze into ice droplets here on the ceiling which does not look to be the case got a little bit there but this is a really small freezer. Okay it does look like the water is coming out just fine came right out here on the ground and froze so we know the line is open so I spoke with the owner he said just go ahead and can this crap get rid of it so we're getting rid of that we'll get rid of this union here you can see we had a coupling here we'll get us a we're gonna run our heat tape that we usually use through the center we're gonna switch this to three-quarter inch CPV or three-quarter inch PVC put our trap on the outside just dip it back up again ours will go right through the center of it so it's not such a big deal this stuff here I've seen some really bad stuff with this it looks like it's already having a meltdown actually right there look at that yeah this crap is garbage there's probably why it's been freezing up look at that it's heat tapes failing either way we need to get this trap we're trapping on the outside we'll get them a bigger drain line we'll get rid of this garbage and then they should be good to go let's uh not to drill that hole out a little bit bigger unfortunately but we'll get her okay so we got our PVC here hole is a little smaller on the inside than it is on the outside so we're gonna have to do some drilling which is never very easy and you got to get through that much of stuff so might try to get the old hole saw to do some of that which is not idea stepping bit ain't gonna work for crap so we'll make her through there just gotta get a little persuasion to it I was able to go and reverse with my hole saw kind of put the edge of my bit up there and just kind of get her to eat into it then once that was done I could level it up and get right on in through there looks like we should go get that through there now and we'll get this thing all in and about yeah look at that it's a lot better here I go so go ahead and get that 90 on the end then we'll do the 45s out here and we'll bring it out down and back up again and that will allow it to drip past the edge of the cooler there and then it'll just be up there in the air less things to worry about it's back here on the backside of the bar areas don't really matter and that's how we do it on a lot of them and it works just fine if you don't like it it's not my problem so anyhow that's that's how we do it and that's when we keep on doing it because that's the way they like it done so here's some of my goodies I got my copper I think that one there's an empty one miscellaneous garbage PVC and some electrical so these are the cheapy ones that are like 20 25 bucks but still you're talking quite a few dollars one is all sudden done but it makes it a lot easier then my ladder holds it in place you guys wonder why I don't usually do a video of the truck because it's a mess I work for a living it's organized within the reason but a lot of it is it's just stuff I need I got to 50 pounders there I got two sprayers there you know I've got my recovery bucket there I mean it's just really it's just full of stuff for jobs this is for my new cart to protect the top it's plastic but this right here was a really nice investment so we're gonna have that actually gonna do that we're gonna do a tee do a tee on the one and then a 45 on the other two 45s on the outside so we're gonna come out go down and yeah back up again and technically probably another 45 on that so luckily we got a outlet right there I'm bringing the tee right into here got a street 90 right here blew this in once I get my heat tape through the center of it you can still get it through there even when it's in place but I'll have that thing bent like about like that that way it kind of fits through here and that way the water won't back up and go out like that other one did and it's gonna go straight out there we're trapping it outside I think the philosophy behind it is the winter time is the only time it's gonna freeze so you only have so many months of freezing cold which somewhere around maybe four months to three months for us and then all the other times it's it's gonna be in a warmer climate so if it's inside the cooler the freezer I should say it's gonna be froze all the time so I think that's why they do it on the outside I'm just copying what I've seen us do over and over we're gonna have to come back though with thicker insulation for this which you know not a big deal I don't think that's what was dripping the timer did kick out right before I started working on this and it kicked out I think it's 17 minutes so the defrost termination is working and like I said it's set for like 35 minutes so go outside here and get that little trap put in there yet here's what we use made in America 120 volt or 240 depending on what we need this crap is 240 or 120 it's a red Kim so we'll split that heat shrink it but connect it usually use a male plug but honestly I think I'm gonna use the plug he had before because it has a nice light on it so we're gonna chop that thing off about right there get rid of that thermostax is self-regulating don't need it and then that way it kind of glows and it'll let me know or whoever know that you know it's got power which is kind of nice so I'm gonna use that plug here whether or not that's kosher or not it is what it is but it's what I'm gonna use usually like I said we will use some butt connectors heat shrink tape and then terminate it off all right it ain't trimmed up yet and ain't glued but I went ahead and feed it to fed it through there that'll work out pretty good and then like I said it will give us the drop that we need all right so we went ahead and bring it down through the center got it taped to the bottom and top of that just so I could get back over here closer to where the plug was at we've got got our heat tape heat shrunk on to there on up to there normally we use the zip cord with the aftermarket plug male plug on it but in this case here I like that because I have the nice lighted plug there now we're gonna go ahead and wrap this thing and then we're good to go some areas maybe you can't use PVC you know what good for you we're allowed to use them here all right finished products we've got the nice heat to cord there doubled it up here to help protect any infiltration from there we've got cable ties across the top around the pipe got foam tape on top to seal that doubled up here and there everything it's good to go it's not rotating it's holding in there pretty good now we've got that piece in there and we're gonna go ahead and put her back to on so that sink and freeze back down a little bit got that door adjusted there so it shuts on its own now got this all insulated out here which we usually don't do but I went ahead and went the extra mile on that was gonna put that other piece on there we don't ever have anything fall down in there got my heat shrink on the end there keeps it out of the water even if it was in there we haven't had no problems in the past and then it's good to go there that's gonna leave it out far enough away from the wall so won't be dripping into the foundation area there and we'll go ahead and get that done yeah this here's got issues I didn't ask him about that it's not like this just happened so anyhow got that there now we just got to get this thing turned back on all right so we verified the sight glass is full which can't see very good from this angle but I did when I had my flashlight out got the clock set back to normal disconnects on fan cycling so we're good to go there that's gonna wrap this one up until we get back with some better insulations all right so we're back it looks like our drain heater things working I have no ice filled up down below nothing up here in the pan we're coming back here to replace this lightweight insulation with some insulation it's actually rated for it I don't see any ice down here on the floor so probably accomplished what we originally wanted but that's still ain't right so we're gonna correct it we're gonna go ahead and throw this thing into a defrost so we can get get that knocked off cut off that's the insulation we got it's three-quarter inch thickness by 7h diameters we're gonna get that on there and let's go ahead and get started on this thing we got a digger ladder out which I don't know if I ever showed you guys this or not but it's my little five-footer just trapping it to the ceiling and out she comes all right so I don't have one of those cool cutters so I just took me a razor blade it's brand new put in my vise grips and split this baby right down the center I like this type of insulation best other than that peel and stick garbage because it comes apart and we're gonna end up glueing this thing with Armaflex glue and this stuff won't come off unless they decide to tear it off with their boxes that they have a tendency to do so we've got this thing into defrost so as that warms up a little bit I'm gonna go ahead and start cutting off the old insulation may have to warm it up with a hand torch but we're gonna get that stuff off got it all off there this is gonna be a lot of fun to try to go through here this ain't seven eights I kind of made a mistake there but it's not gonna be too bad more like five eights we're gonna go ahead and get that on there it's gonna be a lot better than what it was and when it's sealed we shouldn't have too many problems I'm too far from the shop to go get the other stuff but we had to put it back into defrost because it kicked out and I pulled the disconnect anyhow that's where we're at so far just basically use my knife and my little hand torch there to loosen it up and get it off this here is gonna be impossible to get that big piece of insulation in there so we're just gonna use foam tape on that and then the rest of it we're just gonna glue it and slowly slide it around and form it in there okay so here's what we're gonna use thank you you too gonna add a light coating very very light coating on both sides let it tack up so where it's about ready to stick on its own put that thing on there and get started on it so there we go all right so far so good then just gluing it as I go along got it all in there at the top blue too and it's tight it's still setting a little bit there on that piece there but the key to this crap is put it on really thin super super thin like I said I'm just gonna arm a flex tape this thing here at the corner it's just there's there's no way to get around that liquid line so we're just gonna go super thick on that with the arm flex tape this I'm gonna probably do some 45s or 20 some odd degree angle whatever the hell you want to call it but that's where we're at and then we'll glue on the edge corners here on here and it should be sweet to go it definitely is a lot better than what it was trimmed up that extra insulation it was there on the end so we should be just about done here in a few minutes so like I was saying just want to get this super freaking thin which in a string is hell you just want a little light coating I mean it right there that right there is almost too wet I mean it's just just a light coating there I don't have my tripod with me and there ain't nothing to stick it on anyway because everything in here is not in metallic far as metal that will stick to a magnet but there you go all right so we finally got it it's sealed they ain't perfectly lined up but you know that's a hell of a lot of curves and I'm not an insulator but at least we use the right thickness got my new light here the Milwaukee 12 volt there a little rotating head the USB thing of a jig on it just kind of cool just got that and I got the 12 volt band saw or not 12 volt 18 volt compact band saw so I'm kind of looking forward to cutting things in half but got the big battery on there and it's kind of today's first day I've used it so I kind of thought about it after I'm recording it's like man should be nice to have a little more light in here and I'm like shoot I completely forgot about this one thing bad about it is there's no place to hook it so I'm going to try to develop some sort of hook mechanism because I mean obviously it sticks to the wall and stuff but problem is there's no place to put a hook to hook it to your toolbox all right so I've got a wrap around back here added wire ties along here to help keep them from destroying stuff had to do that little thick there which I didn't like but it's too tight but you know like I said there's a little wrinkle here in there but she's completely sealed all the way around same with here here you know that's three-quarter inch thick so little 16th eighth of an inch gap it's there I mean I'm I'm OCD about stuff and as you can tell I mean when you look in there it's tight I'm just picky it's all I am above my stuff but that's gonna be a lot better than what it was and I asked them how they were about stacking things because that's the other thing you have is they'll throw stuff in there and I'll rip that stuff loose they make like a plastic wrap and things like that that can go around the insulation which would be pretty durable but you know it I think we're gonna be fine we ended up replacing this piece out here and then I end up double-wrapping it around there I had to stop it here you had some leftover stuff another piece of this wrapped it basically I made a C channel around it then did the foam tape ain't bad I mean when you balance it with everything else we got going on it's about as good as you can get and then come back around here checking out our trap which it's got water so that means it's working and it's not freezing so they've been hitting that a little bit I can tell then we'll put some silicone around that to help keep it from rotating because it seems that they they are hitting it some but it is doing its job it's pocketing waters got it all insulated I went ahead and use that thick insulation for it so it's done everything's finished everything's cycling correctly I'm gonna wrap this thing up guys if you liked the video I know something simple but it's just something that has to be done you guys like the video and you want to see more like it you know what to do don't forget to check out our Facebook page and the links for down in the description till next time guys we will catch you on the next