Upload

Loading icon Loading...

This video is unavailable.

Clean Skateboard & Longboard Bearings CORRECTLY

Sign in to YouTube

Sign in with your Google Account (YouTube, Google+, Gmail, Orkut, Picasa, or Chrome) to like Rat Vision – Skateboard Tech's video.

Sign in to YouTube

Sign in with your Google Account (YouTube, Google+, Gmail, Orkut, Picasa, or Chrome) to dislike Rat Vision – Skateboard Tech's video.

Sign in to YouTube

Sign in with your Google Account (YouTube, Google+, Gmail, Orkut, Picasa, or Chrome) to add Rat Vision – Skateboard Tech's video to your playlist.

Uploaded on Sep 6, 2011

Learn how to make a bearing cleaning kit for $5.
Go to http://ratvision.com/ for more info.

Before you begin cleaning skateboard bearings it is best to see if the bearings are worth cleaning first. Sometimes bearings get too damaged and are better off replaced than trying to clean them.

For great prices on Longboard and Skateboard equipment we recommend;
http://stokedskateboards.com/

BEARING CLEANERS AND LUBRICANTS WE AVOID:
WD-40 is more of a solvents than lubricants. It is thin to enable it to get into tiny crevices and free up rusty, stuck parts.
ALL Cooking oils
Soaps with citrus scents/fragrance
Dish and Hand soap
ANY Wood polish, Wood oil, or Wood cleaner
Acetone
White Spirits
Paint thinner
Turpentine
Laundry detergent
Bathroom cleaners
Kitchen cleaners (anything that is not citrus cleaner
Orange Soap (too thick, diluting won't work)
Pine Cleaners
Teflon
Silicone

REMOVE BEARING SEALS/SHIELD:. http://www.youtube.com/watch?v=AXmZhf...

TOOLS:
Bearings Cleaning Kit
Solvent. We use citrus cleaner.
Hair drier
Cooking tongs (not necessary)

You can throw bearings in an empty plastic bottle with some cleaner but this method is not as effective as a kit.

BEARING CLEANING KITS:
The easiest way to clean bearing is with a bearings cleaning kit. I recommend the Oust kit because it's compact and comes with cleaner inside.
The Bones bearing cleaning kit is OK and available at most shops, but you can make your own for less money. Read below for instructions.

CLEANERS AND SOLVENTS:
We use citrus cleaner as our solvent/cleaner for cleaning skateboard bearings. It's less than $5 for a bottle.

We highly recommend staying away from dangerous cleaners that people use carelessly in other tutorials. These dangerous and hazardous solvents are turpentine, acetone, mineral spirits, gasoline, butane, paint thinner, kerosene, etc.
Chemicals can be absorbed through your skin and get into your blood stream.

WHY CITRUS CLEANER?"
The majority of citrus cleaners are safe. Most of them have no warning label for health hazards. They usually say to avoid contact with the eyes (of course), and that it might irritate the skin.

Citrus cleaners are made with orange oil and it works by using a natural solvent called terpenes. This hydrocarbon is mostly made of about 90-95% d-limonene. D-limonene does the work of dissolving stuff.

CLEANING KIT PARTS:
1/4" x 6" rod coarse thread (or whatever fits the length of the bottle inside).
1/16" OD x 1/4" ID x 3/32 O-Ring (this is the black gasket/ring. Basically 1/4" ring as thick as a toothpick)
1/4" Washer
1/4" Nut, coarse thread
1/4" Spacers cut from a ball-point pen
1/4" Wing-nut, coarse threads


How to make a homemade skateboard bearing cleaning kit:
1. To assemble the bearing kit start by cutting a small hole in the lid/cap of the bottle. The hole needs to be just big enough for the 6 inch rod to go through.
2. Put the gasket/black ring on the rod.
3. Put the rod through the lid/cap of the bottle.
4. Put the washer on.
5. Tighten the nut down to the bottom of the lid/cap.
6. Cut 1/4" pieces of a ball point pen sleeve for spacers.
7. Place bearings on the rod with 1 bearing spacer between each bearing. (remove seals or shields first).
8. Hand tighten the wing-nut until the bearings are nut on the rod.
9. Fill the bottle 1/3 with citrus cleaner.
10. Place the bearings in the bottle and tighten the lid.

Directions for cleaning with a kit
1. Remove bearings shields/seals first. See how here (link).
2. Wipe off dirt on the bearings and shields/ seals.
3. Assemble kit.
4. Fill the container about 1/3rd of the way with cleaner.
5. Insert bearings.
5. Shake the kit for a couple minutes.
6. Takes the bearings out (leave on the rod).
7. Tap the bearing on a hard surface to remove contaminants.
8. Repeat shaking for couple minutes (repeat steps 5,6,7 if needed).
9. Since bearings off in very hot water (keep them on the rod. This removes the cleaner. IT IS PERFECTLY OK.)
10. Immediately blow-dry your bearings to remove all the water. Use cooking tongs if bearings are too hot to hold in your hand.
11. Lubricate each bearing with about 1-2 drops of thin lubricant. We like electronic oils and sewing machine oils.

WHEN TO CLEAN AND LUBE:
For avid skaters, meaning you skate to and from school and skate on the weekends, checking lubricants every 2-3 weeks is a good rule of thumb. Bearings may need to be cleaned every 3-4 weeks.
For those who skate about 1-2 days a week, you can stretch out the maintenance by lubricating every 4-6 weeks, and cleaning every 2 months.

PERMANENT (NONREMOVABLE) SHIELDS:
1. You can clean nonremovable metal shields the same way shown in the video, or apply lube and ride them until they break.
2. The most important thing to do is dry the bearings completely by spinning the bearings while using a hair dryer.
3. Add lubricant in the gap between the metal shield and the inner ring.

Loading icon Loading...

Loading icon Loading...

Loading icon Loading...

The interactive transcript could not be loaded.

Loading icon Loading...

Loading icon Loading...

Ratings have been disabled for this video.
Rating is available when the video has been rented.
This feature is not available right now. Please try again later.

Loading icon Loading...

Advertisement
Loading...
Working...
to add this to Watch Later

Add to