 Hello boys and girls. Got a quickie for you today. As I was making this video There was small stuff I needed to do before I wanted to do the fuel pump when one of those things was bringing the car down off of Jackstands, but that video ended up to be almost 40 minutes and I don't want to bore you too much So a fuel pump install, which is the 255 wall braw fuel pump. That's gonna be in This is what's 13. So that's 14 and this time Just quickly it's kind of an update. I guess radiator gets installed Car's gonna get lowered and I'm gonna show you an exhaust cutout which there's also gonna be a video on a vacuum actuated What is it that the flappy thing for the exhaust cutout and how I wired it which didn't really work Still working on that, but but that's later So this time kind of an up to speed What was done so far? So as always guys Subscribe like comment this like like whatever do something, okay? You know, whatever you do it helps the channel out and helps me out. So thanks for watching and enjoy the video All right time for another update oil temperature sensor Oil pressure sensor or sending unit Pressure is on the left temperature is on the right Okay, these two fellas Now I ran it over the exhaust here Well away from the Exhaust I'm not putting back the I had I got an H brace and some covers. I'm not putting them back in I Actually made a mistake and Those studs Instead of putting them on the lower hole there while the engine was still on the stand I put them up there. So up there where the stud where we see the nut That's where the bolts go and the nut with the stud goes Where there is no bolts. So once I have it up on the lift I'm gonna Move them around. Yeah, same story on this side, too. There you go So my mistake gotta fix that don't need to do it now and a Little surprise check this out Exhaust cut out Yep Three inches right now. It's blocked. It's blocked off because I don't want to scare any neighbors when I'm gonna start it up. So yeah, I'm thinking of getting a Vacuum flat Or opener, whatever you want to call that thing I'm still debating on it. Those tend to break Definitely not electrical on because the motors simply melt So I might as well just leave it like that do a manual do it manually Remove this this cover and I'll show you what I got Basically remove it at the track, but see it's sticking down a bit I mean it's not any lower than the actual exhaust here, this is a The dumb pipe to mid pipe. This is actually the lowest part of the car. So this is a Little bit higher. I actually did hit this a few times. I don't know if you can see it, but yeah, I mean This is a good exhaust system. This is 12 years old Imagine that Stainless steel high quality stainless steel No rust at all 12 years, man This is what you get when you pay for quality parts. I believe it's turbo excess The the the back the axle back is two and a half and the rest of it Towards all the way to the turbo is three inches So that's why you know, I'm gonna get I do have to get two separate tools I'm gonna I'm not gonna use the cutout auto crossing, but I will be using it tracking the car So removed are simply remove the cover and install this and it's gonna be loud Just to get a go and everything underneath the car is done. I cleaned up the radiator a bit This hose I took it off Replace these clamps With these guys here, so this is good to go And that's what's going in next. Actually, it's nuts. I'm gonna lower the car put it on the floor and Torque down the crank bolts, which I forgot. I should have done it while it's hanging on the The hoist that's why this socket has been here for the past week or two to remind me to torque it down Okay, so that was kind of a Test so you saw it jerking down to 100 that's that's as far as that torque wrench goes I have another one and It's 132.8. I'm just gonna do 133. There we go. Good That's why I had to put the car down on the floor put it in sixth gear and apply the handbrake Okay radiator in now. I gotta do is fix up this harness clean it up a bit over here It's kind of a small mess Connect these two hoses Tighten this up and install the battery. I am gonna put some kind of a Terminal on this power cable here. This is for the Rear speakers for the amp these guys here Yeah, I actually probably something I can show you So we all so we all know I don't know about the 2020s or 18s or whatever STI's but As far as I know You only get speakers in the doors. So one here. There's a pair of tweeters in here You got another speaker here both doors So to get more sound Without getting a subwoofer I Do like listening to my music loud I Install these six by nines and they are all actually forgot what these are Yeah, I think they're they're all Rockford Fassgate and the amp is under the passenger seat All right, I'm gonna do all this stuff and we'll be right back So I didn't like the bracket how it was it was too long It was right about here before and now I had trouble fitting my hand in here if I were to unscrew that can Okay, so I basically cut it in half here and I welded it back together Well, I cut off maybe a an inch in between Well, did it back didn't bother cleaning up the welds on the inside here And but I obviously had to do it on the outside here. So now it's ready for paint and it's gonna be right about here