 Hey guys, Shade Bear 1000 here. Today we're going to try to fix this pinhole That's inside this tank of the air compressor Okay guys, what we've got here is There's a pinhole here and I tried to solder it once but all I did was take some sandpaper and clean it off a little bit It's still got a slight leak to it so we're going to grind this off of here and We're going to try to re-solder that again if not I'm going to try to get some JB welder epoxy or something and Try to fix it that way since I don't have a welder force comes to worse you know I'll have to borrow a welder or something and and I Put a tack on there, but let's see if we can fix it with with that solder first I have fixed these with solder before and the results Was always pretty good except for this time right here But it's leaking right out that corner. So I don't think I don't think I got The right amount of solder. I don't think I got it cleaned off good enough But so we're going to take the angle grinder. We're going to clean that off. I guess I should have hollered noise alert But if you look down in there Yeah, you can see it Right about the middle of your screen right there That's the pinhole right there So what I'm going to do is I'm going to go ahead and try to solder this I'm going to clean it out a little bit more around here some and then we're going to try We're going to put some flux on here and some flux on the The the solder I do have some acid acid core solder. So maybe that'll help I don't think this was acid core that I had on here But if I can get it to drop down inside there a little bit and kind of bubble out You know kind of bubble out a little bit that should hold it, but let's Ah, let's clean this off a little bit more and We'll get the solder out now. We won't let that cool then we're going to close the drain the pit cock And then we'll flip it back over and we're going to let it set for about 20 minutes because remember that pump has oil in it so and It's upside down So we want all the oil to run back down to the bottom of the pump So let's go ahead and let that cool and let's give it a shot and we'll see if we fix the leak If not, well, I have to grind it off and borrow a little 110 just a little buzz box or something maybe and I Think it'd be all right for that. So What happens is see this is an air compressor. They build up with water. They get condensation in them. I Got to drain my big one. Oh probably twice a week this one What happened was when I got it it had sat for I don't know 15 years or something like that. So and There was water in it when I first opened that pet cock. So what happened was the water got in here and it laid right there and It rusted a small hole in it or at least rusted almost through and then when I let it build up with air I heard a little Like that. So I knew that it popped a little hole there. So but Let's go ahead and let this cool. Let's get it flipped back over and We'll we'll turn it on see if we got it fixed Okay, guys, she's all the way cooled down. I let her sit here for about a half an hour Let's plug it in It may sound a little loud on camera, but actually this thing is very very quiet I need to put a new cord on it But let's get it plugged in here And see if we got the leaks fixed See, that's not too bad. That's a lot quieter than my other one Of course my other one's a little bigger and a little older than that one Let's let it run I think it'll shut off I Think I got it set off shut off and they're set to shut off at about a hundred pound hundred psi Let's let it run till it shuts off And we'll see if the leak is fixed okay It's a little looking like right around a hundred ten pounds. It took about What did I time that at three minutes and 42 seconds or 32 seconds something like that? Let me see Let me look at my yeah three minutes 43 seconds is what it shut off at now I'm not hearing any air leaking from that thing anywhere. All right So I know what I've got here Got an assortment of tools. Let's try it. Okay, and maybe we can get that thing see if it'll kick on by itself All right first. Let's try big mama. We got the half-inch drive impact What I need to do though It's right here. I got to flip this over and That energizes that charges the line see it dropped down to about 99 Okay, so that's probably why I was thinking a hundred So now the airline is charged And she's ready to go now. This doesn't sound real noisy because it does have baffles and it does have a muffler I don't like that, but That's try our little 3-8s drive. You can put sanding discs on it. It's not an orbital. It's it's not a da sander but Cycle when it kicks off We'll check and make sure make absolutely sure there's no leaks in it. I think we got it folks Okay, guys, it turns out we did have one more little leak right there around the corner edge of that But I went ahead and sanded that with the grinder like I did the other one and Put a little solder on it and it's fine. There's no leaks now I Did record all that but well, I thought I was recording I had the camera set up But I did not hit the record button So I don't have that footage, but it was pretty much the same as before so again guys Thanks for watching she bear the myth the man the legend. I'm gone for now You