 Okay guys she bear 1,000 here. I'm going to post a video for you guys Putting new fuel lines on a weed eater. I did Get some footage and I got some footage of the beginning of this Which are about to see these two clips I don't know what happened again. I checked it as soon as I Stopped recording and it was on there, but when I went to import it It was not on there. So anyhow, so I'm doing this for you. You get the idea of what's going on I'm pulling the lines out, but I will cut into The next clip it will be me finishing up the lines finishing up putting the lines in the tank and as always as soon as I start recording the Cargo is past. I'm sorry, but anyway guys So I did do that I did get it running and I'm gonna have more how-to videos on this stuff a lot more here in Upcoming days and whatnot. So I Did get a video of the car starting and how it sounds and everything like that But of course it wasn't on there either started the scooter up It wasn't on there either. So but anyhow What I'm doing here is I'm replacing the lines on this Bowlin's weed eater. So we'll kind of get into it right when I just started putting the new lines in so anyway You get the idea and It'll give you something to watch. So anyway guys, thanks for watching So that being said stay tuned here in just a second and you'll get to see that video Okay guys, we're back See the difference there. Okay. What happened? Was This line right here Come all focus this camera is not focusing anymore anyway, right there Where that came down through see how tight that is right there. It's kind of tight because it's got to make a seal there Well, it did get a little brittle I guess so that was my problem. It was clogged So I'm just gonna go ahead and put a new now I got this started what I did was I clipped the end of it off at an angle I'll show you on this old one Kind of clipped it off Kind of like a 45 degree Something like that and got it started down in there now you can use a little or WD-40 there Kind of lubed it up. It will not hurt anything even if it goes in the tank. Remember, this is two cycle So it's not going to hurt a darn thing and then you're just going to pull it through And it will stretch now what you can also do is put them in hot water And that'll make more pliable, but if it's a new hose, you shouldn't have to do that I'm gonna make sure I've got it Plenty long enough Get down to the bottom. What I'm going to kind of do is just kind of gauge it my eye So easy that's coming through there now But you still want to be careful. You don't want to rip it. You don't want to accidentally cut it with your pliers and whatnot There you go, it's nice and free and you don't want to go too long. So I'm gonna kind of gauge it with that Kind of went up through there kind of down Because you want it directly on the bottom. I might have went a little too far just pull it back out This is the filter. I was telling you about This is actually a weight Same thing with a chainsaw It's kind of weighted so heavy to help hold that down to the bottom and this is your filter I've cleaned it out and blown it out with compressed air And there's that so what I'm going to do though. What you want to do is after you've cut that Cut it off straight And get a straight as you can filter back on there Again, if you got to use a little lubricant, it's fine because I Now wouldn't use like petroleum jelly or anything like that, but a little bit of a little bit of WD will not hurt it Because like I said it It's a two cycle engine anyway and for that minute amount even if it wasn't You know, it's not gonna be enough to get it to smoke You want that on there fairly snug to keep that because if you don't that comes up you're kind of defeating the purpose of having your Your filters will blow through it Okay, good. There's that and Yes, it's down right there at the bottom of this. Can you see that? That's where you want to land Okay, so now I'm going to go ahead and trim this about where it needs to be I Don't want too short of a turn Okay, so let's try about right there. I think he's These lines this line kit. See here's another smaller one, which I won't use on this application but I got those two things And a couple bucks. I Mean It was still in my book too much There's like four bucks for a little piece of rubber, but you know, it is what it is this petroleum base So anything petroleum base guys, you know what that's like Now I do remember where this one came off it came off the back like that so it should be Good there. Now this one This thing I did notice. I don't know how they kept it from leaking, but it did leak around there So I'm just going to do the same thing I'm going to put this right down Just right down inside there. I think that's going to give me what I need so So clip this off at an angle This one you won't have to worry about straightening out again because It's not getting anything put on the end of it Hopefully this will be long enough if not I can use a piece of this that is not This is still nice and free on that end of it. So get this started down in here. Can you guys see this? See what I'm doing here. I grew up that down for me. I know my Tiny little fingers are somehow getting in your guys away, but so I cut that in an angle And what you want to do is try to get the long part in first and then kind of twist it around And it should start In there Eventually pushed it out of the way. Oh, I see what I've done I know a lot of you are thinking the lines are just too big, but they are not they are the right size But like I said, they have to fit snug in here So they don't leak but now you can get the next size up that you can make them fit But then they're going to be too snug and it'll Have any fuel You know, they're damn it work for your place than what's going on now Well, that's what could happen I'm about a half an inch in there. I want to get about an inch Here's someone see if I can reach it With this I don't think I can but I got something else that will I've got I've got these that's a little groove. Let's see if I can get those up in here Seems like they need lubed up good like this got it now Bring it now like I said about an inch all it does is just return the fuel back in If you get too much so it does not flood out There you go. See it sucking it up in here. I don't know if you can see that or not real good Let's see what you're looking at here. That means zoom in a little bit Now watch that back line When I cover this hole watch this line right here, I'm pumping this see the bubbles. I Don't know if you've seen that or not, but anyway, it's sucking it up through But this has to be closed off To give it suction. I did blow the cap out to guys Now we should see some up in the primer bulb There's shorter did suck it up into the carburetor, so but Primer bulb could be getting weak off there. I Did see it going up in there It's clear I wonder I got that on the right one I mean somebody else could have switched it Yeah, I was on the right one because I seen it It's like a gas up. Okay. Yes. He bubbles in there. So some of this on this On the ball because it does look low. Oh I think the bulb sucking all the way or two It's going to need replaced. Okay. I do see it leaking around the ball Shit, let me get this around here. So the bulb is sucking here. I'm zooming me a little bit. I know it's not focusing right and Here see bubbles coming out right there. I doubt if you can see it So the bulb is leaking All we can do is try to tighten it for now because I do not have a bulb A new primer bulb through this and it tightened a little bit. We usually when you see that They're sucking air It also has a lot to do with the wet runs to probably why it started sucking it up. Okay, sucking it up now. I Can see it coming up The back tube here, I don't know if you guys can see it See it right there It's sucking it up now Very slowly, but I can still see it leaking right here so what I'm going to do is I'm going to take this ball about and try to clean it and We'll see what happens. Let's take this ball about Yeah, I see a lot of pressure there. So sorry guys See it's building up a lot of pressure in there Just should build up something. I don't think it's supposed to build up that much. So it's not going up in To the bulb itself yet. Okay. I see why right there. See that bulb Let me get you up here right here. See that I need to get a new ball right there That's what was going on That's why it was working sometime because my finger was covering the hole. Okay. All right, but let's see if it'll run now Let's go ahead and try to try to start it up It's not going to run right, but a little bit down in there for the cleaner, which is highly flammable Try to start it right here for you guys a little bit of mixed fuel here Squirt that down in the cylinder. I'm gonna have to check the spark plug. It's right there on top Let me do that and I'll be back right back with you guys Okay, guys, we're back. It does have spark The plug was dry so that meant it wasn't getting fuel. So dump a little fuel in there. Let's see what happens now Dump a little bit down in there and then some through the carburetor This thing it's not going to stay running because this bulb You know this fuel line it's gonna let it suck a lot of air So I doubt if it'll stay around but let's see if we can get it to fire. It does run Okay, so all I got to do is get a primer bulb And I think we will be good to go So and after I do that, I'm sure of course I'm going to have to do some adjusting on the carburetor. Oh, you guys can't see shit. Oh, sorry about that but anyway We'll have to do some adjusting on the carburetor and I think it'll be all right. I've had it sitting out back here for many many months Neglect I didn't have in the garage. I had hers She gave me this one, but I had hers in the garage But that one I was like, well, I'm pretty sure it was right. I just left a light back there. So That's probably what happened to the primer bulb guys. Tell you the truth down here in Florida, man. It's uh, you know hot and and He gets to everything so You guys remember The video did on my toolbox Yeah, I keep missing my mic even turned on. Yeah I'll show you my toolbox. I do finally have some tools been buying a little bit at a time I got you on the tripod. I'm trying to get you in here buying a little bit at a time like I said Some nice tools. This test bird from, you know, Harbor Freight. I do not work for them. They do not Uh Sponsor man anyway Just some stuff. I bought and over time She bought this for me last week in this light so we can get more light in here That's all we've got right now. I've got a battery light blink, but What's going on? I'm drinking soda. I've got a battery light blinking Okay guys, so I want to start the car for you. I'll tell you. Well, I'll do that in my very next video I want to charge this battery and I'm gonna start the car and let you listen to it. I think it's got a bad lifter problem I don't think the top-ends oiling right, but I don't know. I haven't really got into it yet But just got worse and worse and worse. So Hi monkey. She's going She didn't know I was filming, but it's okay She brought her and I gave him a bath. So don't get dirty So anyway, the battery lights blinking guys, I'm gonna go monkey Say something Bye Okay, so every damn time Car goes by. Anyway, we got this running. So I'm gonna charge this I'm gonna charge you guys up and then I'll let you hear the Chrysler and I'll fire up the little scooter for you and show You what I did for it. I'm waiting on some parts, but I did get it running It was just a no spark issue and when I got into it. It turned out to be so easy to fix I didn't even get the camera rolling. So sorry about that But I'll show you guys how to put the new parts in when they get here But I'm gonna charge you up and I'll be back with you guys. Stay tuned for another episode of working in Marty shop Yeah, I'm gonna think I'm just gonna go ahead and start working here. So that's another story. I'll get into Yeah, yeah, I think we'll be all right. So anyway guys We'll be back with you monkey. He'll be back with you and Bruno will be back with you Right. Yeah, stay tuned for the next episode of messing around here. Just little updates and firing things up Let's start some things and and Get some videos made for you guys. Okay. All right guys. Thanks for watching. Shea bear I'm gone. Bye. Bye guys