 Okay guys today we're gonna be putting a new throttle cable on the old scooter stay tuned. Okay guys today we're gonna do a couple parts on this thing because I want to pull the gas tank out and clean it and maybe the carburetor. I just put a new carburetor on here a few months ago you guys might have seen that that video but it started kind of overflowing a little bit and I got to look in the gas tank and this is steel it's got a little bit of rust in it so we're gonna pull the gas tank out too but in this episode we're just going to focus on pulling the throttle cable off so so far what I've got here is I've got the throttle cable off or the throttle itself off it goes on like this it's just two screws in the back of this piece okay here right there and right there no biggie self-explanatory we're gonna pull this cover off we're gonna put this cover off and possibly the side covers down here but we are also going to take this off now I've already got this ready there's a screw in here that you take out there's one down here one down here one right here and one right there and this whole thing will pull out I'm gonna take this out so I can get to the carburetor which is under here and there's the throttle cable right sorry right there so let me get you in the stand and we'll go from there there is also this front cover here okay this is a cover right here it's going to be held on by that screw there and that screw there and I'm going to take them two screws out we'll take this cover off and we're gonna lift this up out of here so let me get you in the stand screws out of this clips in these little clips right here on each side and then down here's the two screws I was telling you about bring this over here now as you can see now we've got a wide variety of how we can get to this stuff throttle cable comes up through here up through here and underneath and up through here so we're going to pull this cover off next okay and this cover has well I've already got them out okay it's got a screw there a screw there and screw there screw there I've already taken these out to save time but it's also got one big one up here in the center I've taken these out ahead of time to save time we're also going to take this front front piece off here and here which is going to consist of screw there screw there and that one there which was has always been missing so so let me get that screw out of there and we'll see what's inside there at this little piece down here at the bottom little piece there little clip clips in this little hole right there and these pieces if we look right here right here so it comes it's got to be fished all the way up through up underneath and up in through here you want it out of the way of all moving parts so let's take this off and you can use your little power drill on here if you want I choose not to because it's in plastic and though it may be a little faster you've got a bigger chance of stripping it out especially if you are tightening this so be careful with them because you strip out plastic you know it's kind of a pain to get it fixed or it's not stripped anymore so this should pop out there's one up in the front right directly underneath the headlight what screw out now unplug this so if I zoomed in here a little bit I'll show you how these unplug they and plug real easy let's push that little tab little tab right there push that down and pull that out now headlight assembly is out the whole thing comes out just like that anyway here is the throttle cable right here right there see that's how it goes down underneath there now this I'll show you right here this is the reason see how afraid that is there you see that I'm gonna get you glasses are falling it's how afraid that is no good that's no good though it was working it was kind of it's a little stiff you know it didn't want to pop back snap back on it so which in turn caused this to break that your actual throttle where this that where that hooks into right there caused that to break so no good which I've got a new one of these as well so this all you got to do on this loosen your jam nut like I said I've done a few steps just to keep the time down what you're gonna want to do just unscrew this just like this excuse me now you're ready to fish this down through now if you guys remember watching carburetor replacement I showed you how to take this off it's real simple you loosen one of them nuts and this thing will slide right out so let's do that right now it's not on there tight now this you open it up full throttle like that and this will come out slide right out just like that and you take this nut off helps if you take that rubber drum at all you slide this nut off like that pull that out and there you go there it is ready to be pulled out hey guys we're back here with this I've got these laid out here the ends look fairly the same there is a little bit of difference but it's to be expected this is original and this is aftermarket the new one does seem to be a little bit shorter I don't think it's gonna be an issue but everything looks to be everything else looks to be the same so I think it's gonna be all right now I did notice on this right up here I put these here you can see the old one is a little bit shorter which is no big deal the new one the old one which is no big deal I'll just cut the new one off here until it fits right where where it needs to be in this so all this does is just slide in there like that so what I'm going to do is I'm going to trim that down a little bit to about the same size because you know I take off but you can't put back on right so I'm going to take them off to about the same size and we'll go from there and I'll see what kind of fit I got and then I'm going to put this back up in there I'll show you how to hook it up okay guys I don't know how well you're gonna be able to see this but I've got this back in here remember we screwed the old one out I just screwed it up in now I left the jam not loose and I left this loose because this will all get adjusted accordingly to see this will go like this so this is going to go in here like this okay now I got to pull this excuse me pull this up here like this down on the other end so I can get down in there where it belongs make sure that's in there straight it should be something like now we're going to slide this on like this now as you can see I've got some painters tape here guys and that's because you know why there's a little hole there in a little tab on one of these that actually on this one get broke off and keeps it from turning so of course I did that too to keep it from twisting on me but someone already had done that so okay so we're gonna put this in here now that's got its own little track it runs in right there too and that's kind of hard to see guys but bear with me now these can be finicky but just just work with it and you'll get it trust me if I can do it anybody can do it I'll make sure no wires are pinched make sure that's free okay now let's get a screw in here just get it held because I want to show you something so that's free now this now when I pull back on the other end down here at the carburetor that's what it should do it should snap back every time like that and it wasn't doing that okay so now that get this there we go now the other screw just the long screw goes in the top grip on here like a deal she can see I took all this other stuff off to show you a little bit better but okay let's get you back down show you how to hook up the carburetor again okay guys I'm gonna try to try to get you in here so you can see this now here's our there's our new cable and again I'm gonna run up I'm gonna run up there like that it's like that now we've got to open this up full throttle so we can get this I know you're having a hard time seeing it but I really can't get the camera any better it's like that I'll let it back then this will all get adjusted see that's a little loose you don't want that that will be adjusted up here on the up there on the throttle and down here so and that gets put up over that okay so now I'm gonna go up here I'll just turn you up here so you can see this what we're doing here maybe that right there okay what we're gonna do it's got a little jam nut we're gonna tighten this bring this out a little bit just until down here it takes the slop out now let's try this make sure it opens up all the way make sure it snaps back and it sure does so now we can tighten up all our connections and there it is so again see before it would come back a little bit but then you had to push it but now it snaps all the way back down to idle and you should be able to see that down here as well a full throttle snap back to idle full throttle snap back now I'm gonna go ahead and tighten these up and we'll be done with this then we're going to be pulling the gas tank out which I imagine means taking all this off okay guys there she is all back together just put it back together the way you took it off sometimes them little clips are kind of you know finicky but you can adjust it and get it where you need it to be but again this is what's that's what you wanted to do and once I get it running I may have to see clear up against the that's your idle mixed or yeah your idle screw so this piece needs to be clear up against that idle screw so it should pop back on its own and it is so there you go and I'm not gonna put this back together yet because we're gonna take the gas tank out here in the next installment so there's how you change your throttle cable on a I think it's a 2013 it is a propel it's a propel scooter so it's just one of them you know it's not a neighbor it's not like a Honda or something there's the number on it I think it's a 49 CC they considered a 50 CC but it is upgraded I do have the upgraded ignition system on it and all that so mirrors are not original someone has upgraded the mirrors so alright guys I'm gonna get ready and get everything I need to get this everything off of here to do the tank we'll do the tank next because I don't want to start it up right now so because I know the tank's dirty so then again I may have to pull that carburetor off soaking carburetor cleaner you know take it apart and all that we'll just have to see once we get there you guys will be with me on that too so again guys thanks for watching remember she bear the myth the man a legend I'm gone for now guys bye bye hey guys today we're gonna be putting a new throttle cable on the scooter stay tuned yeah