 So I've managed to get these out, you know, the way I did it was it was basically to risk breaking one of these tabs and what I managed to do was to just pull one tab back, you know, if I put this, I don't know, now you get these back in there, I don't know, no, that's the right way round, I don't think it is, it seems more rounded there, thinner here, so it's going to go like this, thin end in, and I used a pair of tweezers to get it out, so I'm going to use a pair of tweezers, let's put it in always, trying to be mindful of not, not damaging it, so that's not all the way in, I'm going to get it into the white one, I'm going to put this all around the end in first, okay, so I've got that part in, I've got those two sides there, they seem to be okay, that's just okay, so pushing that down, so that's back in again, painless enough, and then to get it out, because it's not so easy to get out that bottom piece, I've literally just got a pair of these tweezers, not pointy, but sort of round it off, got underneath this here and sort of pulled it back, I've literally just sort of pushed until that's pushed down, you have to be quite careful, and it does, it almost seems like you're going to break the tab, but as long as you're careful you don't break the tab, and I get a sad canopy out, now I managed to replace all these, the shell, and these on the back door for less than £20, so it's not a bad little thing to do, you know, if you want to, or basically if you've broken your shell, you can get all the bits, I've not got the camera in the, I've been busy all day today, so I've not managed to get the camera out, or the antenna has yet, but I'm going to give it that a go at heating it up, I'm going to use the, I'm going to put a little tip in my soldering, or just the tip that I don't use, and just see if I'll just warm it up a little bit, and just see if it becomes, I don't know what the word is, pliable enough, but just soft enough to be able to get this out, so I'll give it a go now, I'll put it on pause just while I saw out a tip for the soldering, and just give me a minute, I've got this like knife type piece, I've never used it before, I'm probably never going to use it for any type of soldering, I can honestly see what I'd use that for, so I'll give this a go and see what happens, okay, so that does, it does make quite a good impression on that pretty quickly, all I'm trying to do is just smell it a bit, but I have to put my extract on, I don't really want to breathe in, I've got a few, so I'll try just by using this pair of tweezers underneath it, see if I can use a little bit of leverage on there too. Okay, that does work quite well, so using a hot iron does do that quite well, I just wanted to pull that piece out there, it's very hard to try and get an angle where I can see what I'm doing, I can show at the same time, just there you go, I hope I'm not damaged it at all, I'm going to assume there's going to be some flexibility in this thing, okay, so that ends sort of, rather than, I didn't actually get to manage to cut through it as such, it just warmed it enough for me to be able to pull it out, which is okay, I've got some clear silicon rubber that I'll, it's like the white solastic, but it's clear instead, that I'll put over that when I put it back in again, so there we go, so there's the, that's the 2.4 gig transmitter antenna, I should probably try and keep these out of harm's way as well, now all I've got to do now is get this camera out, hoping I can get it all out in one piece, I hope that's the only way it's mounted in, let's give that a go, I'm going to try and put some, again the camera switched itself off, but this time I think it was because it ran out of battery, it did actually say it had half a battery, when I first looked, but given that I've done quite a bit of filming I should have really guessed that that probably wouldn't have been the case, again I'm unsure about just disconnecting this, even though I suppose I should, plus it's just some glue there, but I don't know how these go together, so I thought I might let them out unless I take it apart, am I, I should try giving that a look, does that just fit in there, it looks like it might just push in, okay, I'm just going to see if I can just twist off some of this glue, no way I'll be able to grip it with my fingers, still do that damaging thing, so there's the board out, hopefully, okay pulling it around a bit, oh the camera but it doesn't look like I've done any sort of damage, there's quite a lot of muck around there, these teeth brushes, that might be a bit too much, like a yard broom, that one, that's one of these finer ones, a little bit of a brush round, I'm hoping that's not adjusting the lens at all, for focusing, apart from just being a little tiny bit kink, it doesn't actually look like it's doing any damage, so hopefully that'll just go back together again and be no problem, I'm going to leave that on there, even though as I say I'll leave it on now, fiddling with it to pull it off, and it fits in like that, so really that's it, that's everything out of there, the only thing I'm going to do here is the back door, so I'm just going to try and see if that just twists at all, this side looks like it's opened and it's got an opening on the end and this side hasn't, so I'm going to assume that you can pop that out and then shift it out, I hope you can because otherwise I'm going to break it, then the case, I don't really want to break the case, oh okay so for there I just pushed quite firmly down with thumb, like I said it's opened that end on the other side, just pulls that out, so I'm hoping now I can just pull it towards me, just gently, see if I can wear that out, it's a little bit trickier than what I thought it was going to do, but that's a good thing, okay so that's come out without damaging anything, that's fine, really in a way I got a funny thing, that may be able to be taken off and put on when the rest of it's together as well, wrong way around, because I just want to use this on the white one until the white one comes through, but it could take a few weeks to get to me, it could take a week, otherwise I do like getting a bit of flight time in when I can, because I've got some fluids which are relatively close to me, that's good, so I wonder about those washes that were on these I suppose, if I just put the washes back where the washer markers are on these, and of course these will all go back in the same place, and the motor's going to change that, that should be okay, so that's that, that's it completely dismantled, in a way I wish I got that on the end of the film, on the one I've done, but I can just put this to the start of the one of me putting it back together in, and I'll do that once I've had my day.