 Okay, right, I don't know how many hours I've tried to do this, but I'm trying compact it in 10 minutes. Here we go Hubsan H501S Hubsan H501SS Now until So probably probably be about 28 hours now they go. Hubsan official put out the differences between this and this I Would like to just add a couple of differences that they sort of missed out and also just point out the problem that I have with this to start off with The camera is terrible that is actually the image that is my bench and that is the image It's giving not very good for FPV Not very good Okay, so check gyro sensor, that's all it does. It just sits on that Okay, don't move the aircraft. I know I just did that but it makes a difference. You can sit like that for like 10 minutes Now a few differences one on this the camera protrudes out like that It's a little bit rough around the edges. I don't think it's supposed to be visible those edges They're like cold and there's the In the shell you can see there's like a cutaway and maybe there should be something nice. It's like The camera that was on the other one. Let me just back that out and you're into here That all fits nicely If it's nicely so that looks like it was all designed around components and the shell and everything this one looks like the camera has been Designed for something else and then just used on this But anyway, so there's that little bit These are a little bit more smoke As compared to these ones they claim white at the front, but that is the front and We've seen too white to me because of the way it comes through That's what it looks like as well. You know in real life. It probably looks a little bit more Pinkier than it does on there Because it looks a lot whiter in the middle of the light Then it does you know to my eyes it looks a bit pinkier in there. So there's that The antenna for here will not fit it will fit on your other controller But you'll find that you'll get a hundred yards less probably out and you'll have no control That's because The that's a female connector on the antenna and on your controller on the other type controller standard. It's a female socket So you're just not putting anything into anything I don't work very well So that's another And of course the main thing I think personally is the fact that there's a lot of hardware changes inside here So it's not all interchangable That's not such a good thing because I've been ordering parts for this and I'm not going to know until they get here Doesn't seem to be such a slow boat anymore But from China whether the parts like jets could be for this because there's none advertised This was an advertised as an SS This was just a s and the components are not being advertised as s's or SS is So the flight controller that's coming for here May not work with this. I don't know but if it doesn't work with this it will work with this and as this one seems to be fried Because I didn't look at that video. I didn't know that The flight control updates stuff that I have The latest firmware's for this Wasn't going to be suitable for this That's why that's it's stuck on this Because this did fly and the camera works fine when it's been looked through my other controller and it did fly and it was fine but when I got home last night because I Just wanted to make sure you got the latest software in it. I did have the issue I didn't realize about the antennas I put both antennas in my bag and I pulled that one out and I put it on the other controller It was giving me close up flight. It was great. I sent it out a bit. I lost control The wind was coming my way blew it back over me and I just I got clean truck I just I just dropped on the other controller. I just it wasn't very high and I just dropped the Turn the motors off. I Didn't even try to attempt anything else. I just let it drift above me and I was just waiting for it And I just went for the motors And it just turned off on Passed the controller to my mate and just quickly air-caught it. So that's all good You know, so but then I thought well because it's got a bit of an issue. I'll just do firmware update. Probably that's what it's going to be Don't wear updates It wouldn't do the update. I set up the kind of you know the toolkit to version 2 and update toolkit and It's loaded the file, but when I clicked to update it just sat there doing nothing for about 30 seconds And then just come up with a date error And that was it So I thought there's a bunch of batteries charged. I get out first thing this morning. I woke up. It was sunshiney I was straight up Straight up washed up got myself out there didn't even have breakfast And the damn thing won't fly So It's gonna have important changes on the inside To know what's gonna be suitable for repairs and what's not It's got the the camera thing and I only got to be aware of that in case you do for any reason I didn't have a battery for this. Oh And that's loose as well That actually turns now I've had one of these sent to me not a long ago because it's had a crash and I changed the shell for a YouTube view action and His camera also protruded, but it didn't move about That's got definite movement on it. Maybe it's in some sort of sponge to help You know the vibration which is okay, I suppose Because if you got any vibration from your props or anything coming from here I know there's a nice little bit of a flex in here. So that's gonna absorb some as well That'd be quite good as well. So it'd be quite interesting to see what it's like But it's up. I didn't actually have PV with it yesterday. I just had it going around In a few words with a friend just playing around with it, so Good things to be aware of Good things to be aware of. I've of course everything and I've done it within time. Yes, hold on for a second There is just something on another matter. I'm gonna connect up the the other controller Second and just show you that the cameras work fine, but just for now I just want to show you I've connected this up to a power supply okay, and I Thought I explained this when I did a video before about upgrading the batteries in the other controller And why I didn't use a buck converter And the reason why I didn't use a buck converter is because your board this controller The other controller is going to be using a certain amount of power when it runs now If you want that board to use more current You have less voltage. If you wanted to use less current, you have a higher voltage So when I put my batteries in rather than use a buck converter and convert it down to six volts I allowed it to go at the 8.4 fully charged Down to the seven point well six point nine that it would run to On the batteries and that was still being more power than what you would have had if you'd ever just pencil batteries in there But this is why this is why I show you this a basic demonstration here. So this Will run and the battery won't be beeping at you until you go one step down from seven point nine volts So if I go to seven point eight Ah So you can see that Okay But look at the amp as well. So point three six at three hundred and sixty milliamp and as I start going up the voltage Watch the current draw go down. Yeah, so we're gonna get to 12 volt. So as you if you're on a 12 volt battery You're gonna be using less current Then if you're using an 8 volt battery Yeah So that's why you use a buck converter There's one when you put the buck converter in such you're adding some more electronics to your system that it's gonna cost to be in there If it's got a ninety six ninety four ninety six percent efficiency You still lost a little bit in that conversion And then if you got LEDs on it as well You're gonna be using milliamps to be running those and as you're only using a few milliamps anyway for the entire system Why run more milliamps off on the buck converters? There's none of this to anybody out there that's wants to do that But if for me it was about conserving power for all my batteries to my controller rather than other things I went without the Buck converter one because I understand this ratio equals power and And It didn't really matter even I got to the lowest part of these particular batteries It was still enough power to fully run the controller So even when I had to sort the battery out and because it was running in tune as well It was it was going to the red when this was on seven volt and that's ideal for me because then when it's flashing Reds and there's absolutely nothing there. I know that to change the battery and it's still at Run, you know between sort of sort of six point eight and some balls, which is great So there we go. That's it. I think I'm gonna be back on my little thing and see if there's anything else to add All right, so I'm just gonna come back and do this on Seconds he's pressing that Photo button turn the power on keeping the photo button pressed in all time need for an extra second and then you'll have the bind to play I Know you can see that the camera looks fine Very careful because all these things Do you need to have a good old tiny it was after then It doesn't look that clear, but I think that's that is actually Sort of clear enough. That could be That's Try to see How clear that is or isn't that doesn't really see Look It's not focusing and my camera's focused. You can see where it says check Jira. That's focused and So the camera isn't really I'll just try to go across the top of those batteries Just pull it away now just to see if there's a point where it will focus Okay, now, let's see if this thing on the front as it seemed a bit wobbly Let's see if it's got anything to do with the focusing so Looking at that It does to my eyes it looks off focus on there It may not seem like it's that bad because by the time it gets you know rendered and then goes through the YouTube video Process I'll see my look a bit dodgy, but it doesn't look focused and that is certainly not how that camera works That camera's got a lovely lovely thing on it, so I'm just gonna put that there Just because it's easy for me to see while I just put my fingers on the front of there and just sort of moves Focus any better. Sorry if I'm not pointing at the right place All I'm doing is you're just getting a little tiny bit of pressure on this just because it has got a little time moving on just see it moves one way and Makes any difference at all to the focus and it's not It's not is it anything on the front? I can I took the sticker off because that made the difference and Well, I don't think it's as good a picture as what's on here But I won't be able to test that until it is out. So So far with this it's not been the greatest of times and I know it's probably I could Give myself a bit of a blame for not knowing that this was an SS. I Didn't want to say SS because that's Negative every time from Last century We'll start in the middle. Anyway, let's um so This It's not been very good ride so far It didn't come with these pedals either from that one because I was black And you don't need to remove the wire to the flight controller from the power board to change the shell over Just in case you know Anybody thought that was anything to do with because Hobson seems to think that maybe that was a loose wire That caused this to do what it did And I've tried to tell them that there was absolutely nothing wrong with that connection It's quite hard actually get the wire out which had to get rid of all that rubber stuff that they put on And do that clip thing and pull it out. It was all nice and fair. It was lovely but they seem to think for some reason without actually Asking me whether that seemed to be the case whether that maybe the wire was loose When this is clip the ground the wires loose. It's caused Then it the wire to burn Burn out and burn the wire completely in half the cable only one wire in the cable But at two points on two on two on two points Should probably appeal listen. No, I did it. There's a there's actually a photo. You can see on the The video I Just to show you that the video does work from here. It's not as focused I don't think as this video as his camera and I hope there is maybe some way of adjusting that or I hope that it does look better from Maybe a distance Maybe it doesn't matter if it's that Focused in but to be honest here. That's not really It's focused As the other camera, I'm going to put a bloody battery in that. No, I'm not connected because I think that still comes on Yeah Forgive the noise, but I'm hoping you can see that this camera Has a lot better focus Yeah, you can see that tiny. I mean I also You should be able to see that that's a lot better Focus and if we go those batteries again It's definitely a hard on time that one, isn't it? Yep, definitely thrown up a protest that was But it doesn't well, I don't actually have the flight controller connected now I Took the cable out, but it's still there's the same thing with the cable. They're okay. We're not so there's a Just don't know the one that's coming we'll fit into this and Thanks I was really hoping I was just gonna go to the cargo one. I was hoping the parts will be interchangeable I give a you know the motors will still be fine and the shell and stuff But it's gonna be a little hardware that you're not gonna need to swap about Especially if it comes down to the SC and the mainboard part here So Yeah There we go, but it's most definitely I did look to see the way the camera is in there because it's See the two screws That's what camera sits back into and that little plate goes across the top of it and clumps it all into place And that's why you can't move it around in there And it's gonna be the same in the other one and so you can't push the camera back Like I said, I had a repair come at night. I had to just swap the body shell over and I tried to see if I could actually push it Back for him. So it sat in there nicer But he just doesn't It's like it's just the wrong size And afterthought but not using a redesign to a different camera just using the existing camera that looks Okay, but that's not why we buy these things isn't we buy these because the sleek looks and everything and to me I don't really like it like that but other people may like it and that's that's their choice. That's fine That's I just prefer it Nice and flush or even just slightly sat in like that one Yeah, that's that's that's what I got for you on this. I hope some of this could be or may not be Could be helpful to you If you like please give a thumbs up and and I'll keep you up to date I'll let you know when the flight control board comes in with this how far I get with this Hopefully it will just go on and work And I'll keep you informed what I'm gonna say about The other one unless I just send it back because there is that with that as well. So