 All right, no, yeah, I guess a bit of cleanup is in order Okay Much better. All right, I need to figure out how high this thing needs to go in the air To be able to cut the biggest log. I'm likely to have to cut all right with the cutter part here This lines up right with that other part over there So the bottom edge of this That's pretty close to the center of the saw blade and The saw blade is a 12 inch 12 noodle unit saw blade. So we'll stick stick down just over Six noodle units from here 15 centimeters Okay Okay, so the bottom edge of this thing here Has to be six inches above The top of my biggest log Whatever, I mean, it's probably gonna be about a meter like three feet or so All right, let's make some ground Let's say I've got a one meter diameter log which I'm definitely not gonna be able to move anything bigger than that so To cut start cutting the top of that Well, I guess the saw blade actually goes in I don't need the saw blade to be above it But I want to have a little bit extra clearance. I don't know. Maybe it doesn't matter Okay, let's say let's say the saw blade is gonna cut at least four inches on the first cut so that puts my top Two inches above, you know what? I'm just gonna say It's gonna be the topic top of one meter. I've got one meter of clearance in here And that's the biggest log I can fit fine And if for some reason I bring over a log that happens to be bigger than a meter in diameter Like three feet three inches. Is that what three feet in a few inches? I'll just chop the top off with a chainsaw or whatever the bottom actually But I think most of my logs are gonna be more like two feet across So, okay, so let's make this a meter high So that part over there Yeah, roughly a meter that's got an L channel here and a square tube up here and a square tube up there Now how high do I need to make this thing? How tall it's gonna have wheels at the bottom But I want the wheels to be inside it and the bottom the bottom of this pipe thing to basically go down pretty much to the Whatever track it's gonna be on Yeah So actually when I put a track here, it'll lift up the whole thing to give me a little bit extra clearance but let's just let's just say the track is underground for the moment and That way I'll get a bit of extra clearance when it lifts it up Okay, so this has to be a meter This is six inches four inches ten inches Yeah, a meter and ten inches. What are all these ridiculous noodle units doing? Wait ten inches is like 25 centimeters So I have one Meter up to the bottom as you're there and it's okay that this is sticking down It's gonna keep this whole thing from going all the way to the bottom But that's okay because the blade actually sticks down farther than this so that's Totally fine. So one meter and then 25 centimeters or 0.25 meters Up to the top of that. So obviously one point 25 meters Now how much do I want to leave sticking up the top to be able to connect things and whatever? Another 25 centimeters. Do I make these one and a half meters tall? Sure, one and a half meters tall. Let's make that a 1.5 meters Yeah from top to bottom, okay, and that'll leave me 25 centimeters to attach things which is like 25 centimeters 25 centimeters is about That's a little bit more than this page, right? These are eight and a half by elevens. Yeah, that's enough That's enough space to bolt stuff on and connect things and whatever Think all right, let's let's go with that for the moment So first thing I need to do is cut four of those one and a half meters tall two on each side off I 3d this And there one there one here and then one there And then connect in with some stuff Good I found something with metric units 1.5 1.5 meters just under five feet Sounds good Okay, so the post comes right here and then off the other side over there You know what I don't need it to come above the top of this because it's gonna connect with something out here and Then across I'll just connect it like out here So this will actually be able to go right up to the top of these posts So I guess I only need to make them a meter 25 not a meter 50. I don't need all the extra space up there It's kind of wasted, right? Okay, so I've got my red part here Which needs to be able to slide up and down on these blue parts and you know the yellow part is in there whatever I'm just trying to figure out if I need anything sticking above the highest point this can go to I really don't think I do. I think I can just cut this at Scrap the 150 make it 125 centimeters. Maybe I'll leave a little bit extra. Let's make it 130 Yeah, so 1.3 meters is what I want those to be and that even leaves me a little bit more than I think I need Okay 1.3 meters 1.3 1.3 1.3 and 1.3 and then I need to figure well, I just need to go cut those first, you know at least This drawing should have this in front because that's gonna be here. These will be on the outside of those, right? That's why I need it to be above. Okay So yeah first step Cut four of those I'm just hesitating a little bit because I know once I cut them like You can't really put them back together. I need to make sure I cut them The right length. I also have a limited amount, so I don't want it. Yeah, I don't want to screw that up at all Well, I should be able to get three out of this piece and this is less than half of what's out there And three We'll stop before I get to this junk at the top cut it off somewhere Then I can get the fourth piece out of this somewhere with some leftovers for We'll see cut through this stainless part first So this has Some stainless rail on it, which I may end up using One two three four excellent, and I just need to clean them up you know these rivets and glue and more rivets and Get all this stuff off. This used to be a ship mast, so I had lots of stuff Attached to it. One of these goes here. Well one goes at each of the four corners and I'll connect them Up at the top probably just across here The that part's easy Tricky thing is figuring out how this Slides up and down next to this and While it's doing that it has to stay lined up like you can't it can't just be connected at one spot or something because then It's got a state level as it goes up and down All right, there's something I'm gonna try here I'm not sure if it's gonna be any good. Yeah, it's not gonna be wide enough It's clamped on there pretty good. Now. How do I loosen these just enough that this can slide freely? Hmm, it can't be that hard, right?