 Just got this fiberglass back in and this thing on here So now I should be able to bolt through there Into this thing which will hold the bearing there. It's not lined up And then need to attach this up to this just so this doesn't move up and down Drilling this hop hole is easy Drilling this bottom hole. I don't know. It's a little harder because I can't see Guess I just have to use the force The force is with me today bolt it in That's loud right now because my gear teeth are not you know perfect This one I did a pretty good job on this one. I was a little sloppy. I think I'll replace one this one at some point But they work fine right now and they'll probably wear in and get quieter as they you know kind of wear it together I think I want to put a spacer in here There's just a little bit of space in there and this should be forward at like two millimeters Oh wait, but first let's connect this. Oh I found a piece of garbage recently Pick this up from the street the other day I can do something with it. I had a minute. I was a little skeptical of the garbage at first Widen us I melt it out. Oh hot hot hot hot hot. I think that might do it Little rough between the gears, but I wasn't see how they sound Can't believe it the pedal system is a hundred percent done tuned up adjusted refined and ready to go And for every turn of the pedals eight turns of the propeller down there Beauty next is Whatever business is going on down there. I have a set of ease That's fit down there. I'm not sure what holds them in yet though This is my prop shaft tube The roller bearings are going to go in here I'm thinking something on the on the actual shaft will hold these in And we're gonna have to get this thing up to here and Glue it in without getting any glue on the part where the bearings go Rollers go. I'll use this to push this piece up Right up to the line and the brush in here is long enough to reach up that far and I'm probably gonna get a little bit in the wrong spot, but hopefully Any residual smears in there will get smeared up and flattened out by this pushing up Ah crap. I forgot the shaft is in there already. Well, that means I need to Either take it out just pain in the butt or Figure out how to get around it All right to pull that out. I have to get this off which means I have to get this off This is the craziest weather since we've been here And this year has been so rainy Seriously, all right enough rain. This has been like four months. I think I got it I can see a little Bit of the glue there. That's just been smeared right up Yeah, he's squeegee'd it so flat not a problem There's a blob of glue up, you know, that's been pushed up by the thing that's in here and I don't want to put my shaft down and run it through the glob of glue and Make a big mess. So I'm gonna leave that to dry before putting this back in Don't escape. I guess I need to make a propeller Right, I wanted to put some holes in here So water can get through here and lubricate the bearing I'll think I'll drill that hole or two when I flip it back over If I can get a bolt through there and a bolt through there, I Should be good. Just little bolts. They're not too much in the way. Alright, hopefully that's right through the center All right, one bolt in just like it's lined up. All right I just totally made up the shape of this propeller. I Don't know if it's a good shape for this or if it needs to be bigger or I Can change the pitch on this because it's just steel. I can bend it If I need a bigger one though, I can take out the bolts, put bigger fins I think this would be good for a test it's hard enough to drill through this stuff Some kind of hardened stainless steel This was much easier to drill through. I still want to put some kind of like not housing, but like a Streamline thing on here that I'll kind of match with this and then come down and do a point Cover over the screws and the nuts smooth that out Let's sure how that's gonna happen yet. I might want a bigger propeller. I'm not sure though Because it has a pretty high pitch Because I want it to push like a small amount of water really fast Rather than a bigger amount of water slower Because I'm gonna have the motor here So I want this to be able to at least keep up when I'm pushing with the motor too And if I'm not pedaling A higher pitch will make it easier for this propeller to go through the water if I'm just running on the motor Not that that's what we're gonna happen. I'll always be pedaling. Although, of course the pedals can just ghost They can just spin around from the propeller. Let's the bearing in here a little bit loose So there's enough space for any gunk to get pushed through And if there is a little bit of dirt in there, it won't be you know won't make it super sticky It shouldn't vibrate