 Okay guys should burn 1,000 here today. We're going to put a Battery tray in here now you can still buy these battery trays. They're $144 this was 14 So what I'm going to do Hopefully it's not too thick It should have plenty of room for the I Guess hood or seat or whatever to go down And what I'm going to do I'm going to take two of these This is just a layer crossed here, so I know about So I'm going to weld these this white thing is just for a gauge, but I Want to weld like one right there and then another one right over there and Then I think that'll help support the batteries on this wood so Yeah, that's what we're going to do And I can put the Put that wood down in there and then set the batteries on it. Then like I said, I'll have to make a Couple hold downs. I think I can weld this I can clean this up and weld that And then I'll just put a bolt weld a bolt on the end of this thing So that way it'll hold it in right now. Let's go ahead Let's get the welding done and out of the way and then And then we'll we'll get that cut I'm not sure if I'm gonna use a table. So I might use a table saw on it. We'll see but let's get this well Let's get this those things Gotta cut the rubber off But we'll get those welded in and then that'll be ready for to accept the board and then we can Pull the tractor back up here Start off loading batteries on here the wiring I think We'll have to see I may I may work with the wiring tomorrow on it We'll just have to see so stick around. Let's get started on this thing. I wanted to go underneath them So I wanted to go Come on. He's come up through here like that. I want to kind of To go underneath these edges here my recording Yes So I want to kind of get it under here if I can sure I'm gonna do that Might be able to bend it. Let me see after getting your guys this way here for a second Just shorten this up a little bit. I'm this way He's built bend boards like it's work all the time but never this far. So All right Let me shorten this up. I won't bore you with that. It's gonna take half an inch or an inch off And I'll be right back. All right Well, I guess I wasn't recording again But it just pretty much fell in and I just bend it a little bit and goes in there Does move a little bit But that will not move once I Get the batteries in there and get the battery hold down on because the The original one it's just a metal pan. It just sets in there and that's what holds it in These things So once I get them in there that thing will not move Especially with a couple hundred bound pound of batteries. Well, probably more than that but Then it's not gonna move so Now I think I'm gonna pull this out and spin it around and put the cut edge back there the one I cut back there Looking for the factory edge. I might have had it on there. I don't be alright It'll set about right there now Started rain on me like three times. Well, it's starting rain again now Damn it. All right, let me get my electronics inside. Okay guys, you can probably see I Didn't make the rain Hopefully it'll slack off enough where I can get that trailer up here. We'll at least get the batteries on it tonight and Then tomorrow, you know on another video. I can do the cables a Lot of that stuff. I won't show like shortening up the Popbox cable. That's nothing. You just clip it off shortening, you know, it's two wires I will show you how I make the The battery cables for this thing I'll show you that but I won't show you every single one because it's repetitive It'll just be showing you that you know same thing over and over again But Hopefully when get the batteries in here tonight and I can get that cover the battery cover back on a seat or whatever but subscriber of mine Dennis Hi Dennis. Thanks for the shout outs yesterday. I appreciate that Said he likes to hear some stories. I got one for you has to do with a golf cart These stories I tell you are true so buddy of mine We went look at this old truck He liked it. He was like, yeah, he says, uh, yeah, I'll take it. He paid a guy. He paid in cash everything So did I at that time? He buys a guy he pays for the truck. He had some other things sitting around and So they made a deal we bought the truck we get it loaded and he gives every shake guys handed guys That's when you come back after the other thing Perlis is what other things? He says, oh, well you get all this There was an old golf cart electric golf cart Batteries was shot. Who knows what else was shot on them, but it was decent shape. I mean the body was okay You know, it was like that. I mean it was decent and There was a garden tractor which I ended up with it it was fine It just needed a battery and there was an old snowmobile Of course, we you know, I lived in Ohio then there was a snowmobile so Snowmobile was was ragged. I mean we wouldn't have took it But you know, that was part of the deal, you know that we kind of didn't know about but we thought well We'll take it if anything we use parts or something off of them So we get the truck we get the tractor and you know, we get everything back to the shop and The The snowmobile, you know, the tracks were gone the skis were busted off of it handlebars were all bent up It was just you know, it's been racked and it's been sent for you know, 15 years 10 15 years anyway So just for fun one day It was on Saturday, so you want Want to see if this this old snowmobile around us. Yeah, it might as well I mean at least we can do is maybe get a good engine out of it You know the gas tank was okay But the carburetor of course, you know sent that many years with gas in it. It needed clean But we thought well, let's just try it so we check and I'm getting soaked here Shoot all my stuff is getting soaked Okay, so anyway Yeah, I am so my gloves are so helmet so Anyway, yeah, let's try it. So it did have spark Well, you know, it's got spark felt like it had compression. So shot a little ether in to the carburetor and Pulled it twice and I think fired up ran for about three seconds and died And he immediately said hmm. That's a good engine. I see yeah, and I would just need to put it on something And he turned around Looked at that golf course. Are you thinking what I'm thinking? Yep, I am now So Took the engine off that snowmobile put it on that golf course. I mean we did that in a weekend just messing around And that thing we got a run that thing was scary. It would just stand up like this We ended up putting wheelie bars on it because that thing would hook up I mean it would just ride up in the air. You thought you just want to go over and We clocked it behind his Camaro In front of his Camaro we I was behind him in the Camaro Yeah, that thing would run 75 miles an hour. That was scary, man. That was the scariest thing We ended up selling it after we put the wheelie bars on it I mean and we didn't sell junk and painted it and we made sure everything was up to par and The guy that bought it off of us He put a lift kid on it put some big tires. He took it to the mud hole He was out mud hole with it all the time It's called gas line motor sports and it was place you go four-wheeling and Take four-wheel drives and all kinds of stuff they had mud pits and Mud drags and stuff like that. So That was pretty cool I got some stores about when I had to shop in the stuff that him and I built and the stuff I built But there you go, Dennis. There's stories for you again. Thanks for the shout out yesterday So I got to move some of this stuff and Wait on the rain to quit when rain quit I'll speed you up, but I'll show you putting the battery slide the batteries in so stick around seat Put back on so everything's covered up Wouldn't hurt the batteries, but I didn't want the Controller and the charger in there getting wet so Monkey wants to put the original seat back on She says why do you want to be separated because I want to put bucket seats on with a little console in the center and She wants to put this seat on I can fix that But she wants to put that back on but this is what I want to put on it. So what do you guys think? Those are boat seats, but I can get two of them for hundred nineteen dollars. So I'm thinking And I can put me a little console in there with a center shifter a couple drink holders or both Yeah, they would look nice on there and then those backs would come off White and black goes with anything because I think we're gonna paint it yellow Because it's trimmed in black. It looked pretty good yellow and black, but that's a later But what do you guys think it's got white seats on the back? they'll match so When we paint it yellow There's green and white seats aren't gonna match so What do you guys think anyway? I'm gonna call quits for today. It's only like 230, but I Got a couple hours to do just making up them wires and so I think Once I start something, you know, I don't want to stop until I get like at a good stopping point You know what I mean? So I'm gonna call it quits for today. So stay tuned for I'm on my tripod and it's moving on me and so anyway Stay tuned for the next part where we work on the wires or she had to make up one of them wires. I Don't have a crimper. I'm just gonna solder them, you know, a lot of people say well solder cracks Well crimping comes loose, you know Sotter you get a better connection. This is my opinion, you know from what I found doing things like that a lot I found solder works a lot better, but So anyway guys, thanks for watching Shade Bear the myth of man a legend and go for now Appreciate all your support Don't forget check out monkey 1000 channel. We'll see you in the next one. Bye. Bye guys. Take care and stay safe