 Hello everyone, welcome back to Apple Bay. In this tutorial I want to show you how to put the strip on the iMac, how to center the screen properly as sometimes they go a little bit left or a little bit right, and how to seal the machine properly, making sure you can open again if you have to do it again, you know that if you have to replace the hard drive or whatever you have to do, I'll show you how to do it on a very very easy step. So let's start it. Okay, first of all we need to remove all the tapes around, so everything is clean and ready to go. Secondly, make sure you use the right tape. Don't use those cheap rubbish from eBay. Find a supplier who can give you a decent quality. These are replacements, they are not Apple, but they can split in between the both tapes, otherwise if you buy those ones from Apple, sorry from eBay or you know cheap website, you're going to break the screen once you try to open again. So this is the way I like to do it. I'm not saying it's the right or the wrong way, but that works for me every time. So you got one side and the other side. So this goes that way, yep. So remove the back one, place on the hole, they got tiny holes, keep it straight, pull the back, keep it straight and that's it. Next one, you can do in any order, doesn't have to be in the order I'm doing it. Again, you got a tiny hole, let me see if I can focus, that hole is the same here. So you just match, if you're not really able to do it, take a pen, take something, put through the hole, put on the hole there, stick a little bit, yep, that will do. Make sure it's straight, pull the bottom, do not stick yet until you're kind of like straight, then you push down. Right, so far so good. Just carry on doing it with the other tapes, same thing, same thing. Pull the bottom straight in line, gentle push with your finger. Right, the bottom is slightly more difficult because if you go over the edges, then it's going to be a problem to put the screen. So, how we do it? We take it completely, yep, and you hold one end and the other end. This end goes all the way close to the edge, stick a little bit. And this one, kind of like pull up and down, then go straight. This tape is for the newest model, is for the 2019 model. They do have the microphone, this model, the microphone is on the top. The 2017, I believe, and the 2019, the microphone is located on the bottom. So this strip have a little cut on there, probably you can see there, for the microphone. However, they work fine on this model, it's not a big deal. Okay, let's do the last one. Same again, all the way to the edge. There, stick a little bit, so you got something to grab. Then, probably halfway through, push in gentle. There, the last bit, push there. And we're done. Don't remove any tape yet, just leave it as it is. Now, it's the tricky bit. So, take a packing tape, maybe around 30 centimeters or 6 inch, I believe, so I'm not really getting inches, place in the bottom. Okay, bend this one. Then, you grab your screen that I think I forgot to clean it. Not very good. So, make sure you clean your tape edges. I forgot, nice. Right, so this video is going to take slightly longer than I was planning today. Peel it off, don't worry about the residual glue on there, it doesn't matter, just leave it. Make sure all the edges are clean. And be really careful with your screen, do not chip it, it's very expensive. In UK, this 5K screen, they are about 420 to 480 pounds on eBay. So, I assume the main dealer will charge maybe 650 pounds to fix it. Or we know this repair art, not cheap. So, really, really be careful. If possible, put something soft on the bottom to hold the screen. I've been doing this one for a long time, so I'm quite confident in doing it this way. The screen is clean. So now, without removing any tape. Let me move a little bit this camera, sorry about this one. There we go. So, without removing anything, this is the tape, just the cello tape. So, you put it there on the edge, really nicely. Put it on the other edge. Make sure you are 100% true on both edges. Once you are 100% true on both edges, tape it. That's the trick, tape it. Now, you can tilt your screen. Gentle, tilt the screen. Now, you can remove the sticker, just the bottom sticker, not the top one. Because you already center with the bottom tape. It will be easy to put in place. Yep, sit on the edge. Pull it up, it's a bit tricky now. Sorry folks, this is because the angle of the camera. There we go. Then you put it back. You push that one, make sure it's proper tape. Now, you can connect inside. Because this is not coming out, I'm just holding with one hand. Connecting my backlight. Connecting my LDBS cable, or screen cable, or LCD cable, whatever you want to call it. And before pulling the other tags, I like to test the machine. I always test it. Otherwise, you get wasting more tape. You know, the strips. So make sure all the connections are fine. Machine switching on. This, I didn't test the machine. We have some replacement inside going on. So come on, we're waiting for a flashing folder. Our client's backlight is on. Yeah, there we go. Flashing folder. So we do have a working machine. Now we can pull the tags. And just close it back. I'm not going to do it yet, because I may need to replace this hard drive. But this is the way you're doing it. So this way is through center on both sides. So you have the guy off the tape. If you're scared to do this on the table, you can probably do on a cushion table with, I don't know, some tower or something else. You can do flat. But this is a really good way to do it. So you always get center. Thank you very much and see you next time. Bye.