 Hey everyone Shaber 1000 here today. We're gonna be working on this pressure washer. This is not the pressure washer This is the engine for the pressure washer That's the pressure washer. I'm gonna be putting a pump on this, but before we do that There's a Right up under here. There's a camshaft that comes down through there's no ring And it's got a leak in it. So we're gonna change that o-ring first. So stick around Okay, so there's four bolts on this thing We had to This was my friends. He ended up giving it to me We had to put a Rocker arm in this thing Last year I think it was So I've had this off here before but there's a seal down under here. That's leaking. It's not a seal It's an o-ring These things are a pain to get off sometimes and you want to be Careful and try not to bend this up too bad But I didn't know at the time it was a seal leak and I thought it was this gasket because they are notorious for leaking So to save you from the boredom of me trying to pry this thing off of here I'm going to Go ahead and get this off and I'll bring you back. Okay. It's almost impossible not to bend these things But just make sure you get it straight now Now this is a camshaft Well, this is your camshaft. This is your cam gear and It's what we're gonna do We're gonna I'm gonna pop this out just a little bit right there's the o-ring. Can you see that right? There's the o-ring So all the that's all the farther. I'm gonna take it out Because I don't want to have to put this thing back in time I know it's in time now because it runs it just leaks a little oil So I'm just gonna leave it like that. I have a dental pick here That I'm going to use To pop this o-ring out of here You would think it's Honda you would think they would come up with a better Solution than this There's the o-ring It's real real brittle as you can see it cracked So I have my o-ring kit here Make sure when you use these o-rings that they're good for oil see if I can Find the right one here. I'm sure if that's it or not We're about to find out Went up there real easy. I don't know make sure you lube it up But in this case it's already got a will on it. So what I'm gonna do So I've got some of this stuff. This shaft does not turn. Okay, it does not turn All it does is hold your cam gear on there So what I'm gonna do is I'm gonna get a paper towel. I'm gonna clean that up real good And I'm just gonna put some of this stuff on it then I'm gonna clean this all off with a wire brush and This is drill Dennis gave me. Thank you Dennis I Use that thing a lot And then I'm gonna push that up in there like I said, I'll put some of the sealer around here and I'm gonna push it up in there and Jish neighbor holler in the first dogs every day Let's his dogs out and just let them run then holler for a half an hour. Sometimes he's got a good looking for him Jish You know take care of your animals people Let me see I got a better o-ring. I think will fit better on this one. Well More like the size. I think you pull this one out Because you should Sometimes you got to tap these things back in because they're such a snug fit So if you got one of these Hondas like this And you see drip oil dripping down Bottom of it. That's this could be the problem. Let's check that o-ring That looks like a better fit But I am going to go ahead And put some of the sealer on here anyway just to make sure so Let me get something to open this my cat broke When I screwed it on one day the cat broke and I didn't know it now It's all hardened up here at the end. I tried to drill it out But so I'm gonna cut this corner off here So I can Put sealer on everything. So let me get this stuff cleaned up and I'll be back with you Okay, let's go ahead and put this back on Without trying to make too big of a mess now The reason why I'm not putting a gasket on here is They don't make a gasket for it and the reason why they don't make a gasket for it is because It never had a gasket out of the factory so That's why you don't put gaskets on these I'm just going to snug them down right now. I'm gonna let it set for about 30 minutes And then I'll do my final tightening With a regular Ratchet that why I don't over tighten it that this thing's got some torque It's just a Harbor Freight. I've got that like what five years ago or something like that All right, so Now that should be that I guess one good thing About this being like this I can you know Kind of make it real tight there and put it in a plastic bag Cuz I'm sure I'm gonna need that on the Toyota. We got the heads going to be here Monday and I think the rebuild kit's coming tomorrow So once I get the garage cleaned out we'll get into that Okay, so now the next thing we've got to do clean that shaft because well You want it clean To put the new pump on. Oh, well you've probably seen it in the title, but we're replacing the pump So I'm going to clean that off. That's kind of boring. I know so I'll clean that off off camera and We'll get ready. I got to put The pressure washer up here will put the engine on then the pump on because the pump The pump bolts are actually the motor mount bolts too. So so it's funny because It's not funny. It's kind of stupid But if you look at that right there There's the shaft that comes down Get your son over here There's the shaft that comes down out the Cam shaft Comes down here and this thing here for the valve cover Comes down like that just to keep that shaft from turning So you you would have thought they would have came up with a better idea than that But I am going to go ahead and I'm gonna clean that shaft then we'll get this thing up here and we'll get the pump in that box out and We'll see if it's going to work. Okay on here. Okay, let's go ahead Open up our box here neatly packaged This was unbelievably cheap 60 some box I think Now what's going to be different there's gonna be something different from this than the old one is the old one Had longer pieces to come out to put your Your hoses on Okay, they came out to like here, but as long as I got room It's it should be all right I think it comes with a new key, but that keys that key stayed on the engine so does come with a New filter and hose for your soap and stuff. Here's the bolts Yes, there is a new key there but We're not going to need the key There's been bolts are wrong enough Okay, should be a direct fit. All right, so now Let me move this out of the way Yeah, so he just gave this to me and He said, you know get you some parts for it and You probably sell it like I told monk. I said, you know, I should go ahead and get the parts for that pressure washer and Just sell it She said or you can go ahead and get the pressure get the parts for the pressure washer and keep it She was right. We do need one. So okay that down there. I'm gonna get the pressure washer up here I won't get the motor sat on it We'll get everything hooked up. I'm gonna have to go get a couple wrenches Hang tight guys. All right. So the first thing I'm going to do is set the engine on And then I'll spin you around So you can see The pump It's going to go on under here. Now. I can't flip it up because of course the engine will fall off but The pump is going to go well, I Should have put this in here first Pump is going to go up in here Like so All right, so let me get that started because you're not going to be able to see anything all I'm going to do Is get it started on the shaft I? May have to turn the shaft or whatever and And just start the bolts up through and then I'll tighten them. Okay, so the Sun went away Here's what we got going on. I had to turn the engine around Because the pump Was for rear which that's what it came off of and I wasn't thinking this is front So all I did was just turn the motor around And I just had to drill two holes But I have to go get bolts because the bolts they said aren't long enough and for some reason I cannot find bolts for this thing and I kept them because I knew I was going to be probably either rebuilding at other pump or Putting a new pump on this So I saved the bolts and I don't know what I did with them So I got to go get some new bolts so stick around guys. I'm sorry the Sun left us But I was I want to do this out back in the Sun because it was chilly. So Let me go get some bolts and I'll be back with you. Okay guys as you can see it's dark out Pumps on sorry. I Was thinking I was looking at the old pump. It doesn't have the extensions. It's just like this. So I got to put some oil in it and some gas I did drain the gas and I ran it out So oh I got to put this on This new hose. I'm gonna put the new hose on. We'll take it out front I got a new wand and new hose for it We'll take it out front and give it a shot The reason why it's so late is we was down at the end of the street down here But the gas station watching sick week cars go past so It's just a quick video. I got a few of them, but I'll throw that video up after this one. So Stick around guys. Let's get this out front and I got to pick up some tools. It's not that late, but it is It is evening time It's only what 652 so Yeah Awesome. All right guys, let me get that put in there All I got to do is just shove that hose in there and put the The filter on it so cool any plugs in right down there That little a little black valve right there plugs in there and up here That's the outlet Wait a minute. What's this one for? Think that's the one for the I'm not sure I'll have to check it out. All right guys hang tight We'll bring us around front and try it out. Okay, so what what I did. I wanted to clarify this this pump That was on here was taken off and put on the other guys and It came out where this tank was All right, which his tank was here So since he didn't want the tank it's got a busted nipple on it But I'm gonna use that as a gas tank his his came out here. That's why I was thinking that so Yeah so I got the Kind of like a left and right mess up, but that's okay. I got a bolted on there. I just drilled a new hole here and a new hole here and it bolted up and One back here on this side. You can't see it cuz it's down underneath. Okay, so All right, again, let's get some oil in it and some gas and we'll take it up front and try it out with our new wand This is 3,000 psi pump well pump and And I got a 4,000 pound or 4,000 psi wand and hose so That way if I ever want to upgrade this I can awesome. Okay guys. I know you can't see much, but I'm gonna Start this up And then we're gonna spray some water down here on this concrete right there and See how well it does Well, let's see if it'll run first It's on gas is on Chokes on Trying to get another nozzle. I put all the nozzles up in the hose Up there on top. I can't get them out I want to try another nozzle I can get it out of here. I just put them in Hang on a second. That was stupid. I had to use pliers to get it out. Let's see here Can't see much, but And they're super duper tight. I heard that rattling noise. I thought I had a wrist pin slapping or something, but It's just this thing rattling. These wheels are all plastic But I have a set of pneumatic wheels and tires. I want to put on there so It'll be easier to wheel around So I'm gonna start this back up and there we go and let it run the Fuel out of the bowl of the carburetor And I think we're good to go That's pretty good. That's what 25 Yeah, the first one we had it on here. We had this one then I went to that one. This is zero That's for soap and stuff over there. So I Didn't put the hose in yet, but I'm going to Yeah Because in order to put that filter on you got to put your hose in there and then Fish it up and so you can put the filter on and then put it back down in but so it works fine it'd be good for washing the vehicles and Yeah, so now I got to do the whole driveway, but not tonight So there you go, monk. I built you one. I got clean it up and stuff There you go, monk. I built that just for you Because I took the engine what was it I Can't remember. I did a couple videos on them and then the pump went bad and his other one So I took the pump off this one and put on the other one. That's what it was So all right guys There we go Thanks for watching. I appreciate it. Sorry that we had to do this in the dark but Yeah, this thing's been sitting around the side of the house covered up Of course the motor wasn't bolted on it was just laying there with a tarp over it Hasn't been running several months And you've seen it fire up so That's got high tests It's got 93 octane in and I just put in it because I had to get some for the vet Which the video is coming up for that. I'm going to pull the the Fuel filter off of it from looks that fuel injector had in there. I'm going to pull the fuel filter off Backflow the fuel line Blow anything out of the fuel line And then you know I'll put the fuel filter on and I'll put some Fuel injector cleaner in it. I usually don't use that stuff because if it cleans your injectors It cleans everything all the way up through it and can actually clog your injectors But since I'm going to blow the line out, I think it'll be all right So yeah, there goes. So I'm going to start up Let it run the fuel out. We're good to go. I just checked that pump was 55 dollars on amazon so This wand is Like 40 bucks. So I got like 90 bucks in pressure washer Cool. All right, guys. Thanks for watching. Shea Berry the myth man ledge. I'm gone for now. Don't forget to check out monkey 1000 channel appreciate it and Hey, go give Dennis Hallbacker a visit. He's the one that gave me the drill. I was using earlier with the uh With the wire wire wheel on it. So thanks, Dennis. All right, we'll see you guys soon. Bye. Bye and take care