 What is up guys, Joe Holland here. I am here with Donnie Johnston. We are gonna make a Brandon box for the Otter Large Pro sled. I already have one made, but I got so many requests on how to make one of these that I decided just to make another one. So sheet of plywood, this is three eights. It's a four by eight sheet of plywood. Donnie's gonna measure this and split it up into thirds, which is 16 inches each. 16, yep. So he's gonna, I got them marked out. We're gonna snap a line. So you hold that in. All set. Yep, the hardest part right here is marking for the inclines of the sled. So we're gonna push in with my knee on the outside. So I'm flat, Donnie's gonna lower his down as much as he can. Right there, I would say. Yep, and I'm sitting on mine flat here. He's gonna mark that incline. I'm gonna put a nice little mark on that the whole way. How does that look? Looks good on the back here. Pretty good. That'd be the tightest spot right there. Yeah, that'd be perfect there. Boy, that is really, really close here. Close enough? I think so. I mean, that's really close. Yeah, it's nice tight fit here too. Yeah, yeah, that's great. What we have here, guys, I'm just leaving these in here from last time is this is a two by two. It was a two by four, I ripped in half. And then the other half's underneath. And these are just screwed together, kind of sandwiched, and that gives you something to screw into the sideways. Beautiful. Nice. Okay, that'll temporarily hold it till we get the end pieces. Donnie's gonna cut the upright corner pieces now that are gonna catch screws from both directions and strengthen the whole box. Want me to cut that not out or cut? No, no, sorry. I should be about there, I thought it was just 41. I had to really tell, I would say right about there. 41. 41, we'll try it. Yeah, it seems like it's pushing it out. Yeah, try it right there, yeah. Hop's gonna come right there. Does that look all right? Yeah, the bottom's good. So that's the front ones. I think it looks good. There's not much for air. Yeah, it looks about the same. Yeah. Hold my foot out. Cut the side. Right there? Can you kick it in there? Yeah. Okay. This is a... It'll be free, I think. Yeah, this back's gonna be perfect. You want me to push that in for you? Okay, I could always come back and pocket one in there like a long one. Okay, so you're just gonna do a couple of just... Am I just gonna hold it so you get the longer... I think the longer ones would stiffen this better. Yeah, for sure. I hate that. The lamb? I can't delaminate it. Yeah, I'll probably sand that right off. Put a little glue in there. Yeah. Clamp it back. Okay. The measurements of the box on this... I guess this is the largest sled that you can purchase. Yeah, the Otter Pro Large. Yeah. The width is 41.5 inches, outside to outside. And the length is 83. 83, what did we add for an Otter? On the front of it, it's a little bit different on the width. Yeah, it's 43.25 on the width on the front. What was it on the back? It was... Well, that's the front. Well, that's the front. Yeah. Okay, on the front, it's 41.5. What was it on the back? 43.5. On the back, it's 43.25. Awesome. And then what we add for height back here, was it a true 14? Very... 14.75. Yeah, and then here it'd be 16. Right, 16 on the sides. And then we traced the angles on the two ends. So it was good and tight, good and tight down here. Fits beautifully. Dry it out before we paint it. All right, looks good. Well, that's it, guys. That's how you build it at home. It was two 2x4s and one sheet of 3.8 supply woods, all it is. And Donnie and I are going to pick up a can of paint. I'm going to sand the top and sand everything smooth, so we don't get no splinters. Yeah, knock the edges off, because supply wood has a tendency to be pretty splintery if you don't round the edges. I'll hit all the edges and we'll let this warm up and dry out in here with the fire. And then we're going to throw a coat of paint on there. Donnie said I ought to put Joe Holland Fishing, maybe a YouTube logo on there. What do you guys think? You definitely should. Yeah, you definitely should. Donnie says, do it and leave it in the comments What do you think I should put on there, guys? Not quite like a glove. Like OJ's glove. Like a glove. Nice. And all we're going to do is just screw into those cleats that we have already fastened to the plastic sled. Pull it in? Yeah. So we're going to put washers in front of those screws so it doesn't suck in. Well, we just got a two inch screw there. That's nice. Yeah. It was a little more challenging than I thought it would be. You know, when we were making it because of the scribe and you had to do on the side pieces, it's pretty impossible with one guy. I mean, you can do it. But having two people involved really helped out there. But it went pretty well. And it came out nice. I think there's two by four dot stiffens it tremendously. I don't think we needed them on the back. Big plus seven, man. If we had to, we could add one here pretty easy. Right. But yeah. But I don't see any need of it on dinner. Well, there's some gift to it. But you know. Thanks for tuning in. Hope that helps you. Hope you guys build the box for yourself.