 Shea Bear 1000 here. Today we're gonna be dismantling this little dresser and I'll tell you why here in just a minute. Stick around. Okay guys so a couple years ago I had fixed this dresser. It always sat in the closet because our room's not that small and it's a big there's a whole bunch of these things. There's just not enough room for this thing anymore. So since we did to redid the closet we fixed this because the drawers were sticking and it worked okay for you know well it worked beautifully for about another year and then it just started getting these pieces in here on the sides. They're plastic and they start breaking off and chipping off and the drawers start sticking again and then you're pulling on the doors and they they don't want to come out. So what I'm going to do is I'm going to dismantle this and I'm going to make two shelves. I'm going to cut this around the edge off here and then I'm going to make two floating shelves. I'm going to use these. I may have to cut. I got these long on purpose. So what they'll do is once I cut the shelf cut this in half. This top is going to make two shelves. Okay and then what you do is you drill a hole. Like I said this rounded edge is going to be trimmed off. Drill a hole and these will go inside like that. Then what you do is you mount this on your wall same way with one on the other side then you just slide your drawer or your shelf over top of it. I will put my camera my my vintage cameras and stuff my camera collection on these two shelves. So I ordered some of these. I got eight of these enough for four shelves. On Amazon I think it was for yeah it was Amazon for like 20 bucks. So that's pretty cool. I don't have a drill press to make sure that that's going to go in straight. So I've got plenty of room so hopefully I can drill it straight enough with my hands. So that way it'll set perfectly against the wall where it needs to be. Now I don't know if we're going to keep it like this. I don't know if this is going to come clean. There's like a water stain here and I don't know if it's going to come clean. So she may she may want to paint these. We'll just have to see but this is from June 12th 1978. So kind of a shame but then you can fix these but I just we don't have the room in the bedroom for this extra piece. So I'm going to repurpose it. So it's still going to be used. Like I said this I don't think this is going to come off. Most of this is going to be it's going to be cut off right down through here. It's going to be be straight and then I'll cut these in half with my little table saw over there. But and then I'll reuse some other pieces on it. I'm not sure how this thing comes apart or anything yet. So this part is screwed on. So I don't know. I'll get a rubber mallet or something. But first I'm going to take this piece off first and then I'll probably pop that back. It looks like it's just stapled in. Yeah it's just stapled in. We'll pop the back off. I don't know if this is glued in with dowels or what. I'm not sure about that. We'll figure it out. You say I don't want to break any of the wood. It's still good wood because it's real wood. I think we'll know once we get together. I don't know if this is veneer or not. It doesn't look like it but we'll just have to see. If it isn't that's not a big deal. It's getting painted anyway but I'm going to repurpose this. So let's get started on it. I got my little thing out here. dowels and glue and screws. That's not real wood. That on the sides is not. That's press board on the sides. Hmm I'll be back with you. That's for sure. I might be able to use the bottom for something. Change of plans. We're not using that are we mama? No. We're just going to get a nice two by eight and that way I can sand it and we'll stain it the way we want. I'm using this crap so I don't feel bad about tearing this thing apart now. I still wanted to repurpose it but the front of the drawers I can still use those at a later date. I can probably repurpose those for something but and the handles the drawer pulls. I can save those. So but this going to burn in pile. So stick around when we finish the shelves. I don't know when that'll be but for you guys it'll just be a second so hey. All right guys we're back. Just went and bought. These are gonna be my shelves. Just went and bought some new ones. I got an eight footer two by ten which is really not two inch and it's not really ten inch. But it was eight foot and a quarter. So I told the guy instead of me I have to come home cut it. They cut it for you. I said split it right down the middle split it in half. He threw it on the machine. He cut it. He said you guys have a good day and took off and went and clocked out. One of them was this much too long. So we had to have another guy come back and cut it the right way for us. That's how much too long it was. He didn't even cut it down the damn middle. This one was 47 inches and 7 8's or something like that and this one was 48 inches and 3 8's or something like that. He didn't split it down the middle. What an idiot. So the other guy was real nice. He was really apologetic about the other guy and I said well you know it's you know you don't have to apologize for his stupidity but he cut it off for us and these are perfect now. And I grabbed this I said we paid for that I'm taking it with us. All right Monk. Yep so I'm gonna wipe them off now. Yeah she's gonna wipe the dirt off and we got some stain. I'm gonna put some stain on here and we're gonna let it dry and then we got to take a bed apart right. Yes. And then by then the stain will be dry and we're gonna use our new drill press over there. Well it's not new but it's new to me. There's a video on that. I don't know if it'll be before this and probably after this but anyway there it is. So yeah she's gonna wipe it all for me. I'll throw some stain on there. It'll dry and then we'll come out and drill our holes. I think it's pretty close already. I will probably give it a second coat. We'll see. And to my keen-eyed viewers yes you saw that right. I didn't sand nothing. I didn't plane it. I ran it through joiner. We did that on purpose. We're going for that rough look and you know this is going to be the bottom side because that's what you're going to see. So the knots I think it's going to look good and that's what we're looking for. So I'll be back with you guys. Okay guys we're on day two. Stuff's set up. That's where Monkey wants it to be. Two coats. Now I'm just setting my board up so I can get ready to start drilling the holes. Now I'm going to show you how I mark for the center of my edge right here. I'll show you how I do that. It's real easy to find. You don't have to measure or anything like that and figure out what's half of this and half of that. I'll get to that here in just a second. Hang tight. Okay guys so here's how I mark to get the center of the edge of the board. I'm just going to take my speed square here. I'm going to put it right on the edge. I'm going to mark this down like that and I'm going to put it on the edge just like that. That is perfect center. Now let's check it and be sure here. Okay so we've got inch and a half board. Alright now we go over here measure the center and there's three quarter. I don't know if you guys can see that. Let me see if I can zoom in on it for you. So you can see right there's three quarter. You see that? I know these numbers are tiny but right there's three quarter. There's inch and a half over here. So right there three quarter. I work on any board. There you go. Perfect. Alright now what I got to do is my drill bits are not long enough for this whole thing. So I just want at least half of this which this board is nine inches. Nine and an eighth inches. So I really all I need is go half of this board. So I'm going to take my drill bit. I'm going to measure up to that and it's about four and three-quarter so that'll give me my half and also because down there I've got the knot that I would have to worry about. So what I'm going to have to do is I'm just going to have to cut this down whatever I need it to be. Once we draw our holes and then I'll cut these down all the same length because everything's going to be the same. So let's get ready. Well this has got a nice little holder for the key up here. You can see a van in the background. Mom's coming home today so that's her that's her hospital bed and her oxygen. So there's that. Just gonna set that there. So yeah I will be doing a video on cleaning this old drill press up. I think it'll be fine just to you know clean the chuck up and you know get all this stuff off of it clean that clean the rust off of it. Hopefully this bit is not bent but we're going to find out where she talks so loud on that phone don't she? Okay looks like it's going to be okay and once we get this up here awesome. Alright I may have to raise this up just a tad bit. I'm trying to get all I can get. So let's see we've got a nine inch board and I'm going to be able to make a five and three-eighths. Oh five and three-eighths deep. So five and three-eighths is going to put me down a little more than halfway about two-thirds. That'll be plenty because I'm not putting heavy stuff on here. If it was going in the garage where I'd be putting car parts and stuff then I would go pretty much the full length. But since this is just going to hold my cameras it'll be fine it'll be plenty deep enough for that. So let's get ready and when I get this set up I'm probably going to put a clamp on this because see as you can see that board it's not right there. I still can't get over how much that guy messed up. This board I measured it was eight feet and a quarter inch. All he had to do was measure over four feet and eighth of an inch. He couldn't do it. Those are the guys that want 15, 20 bucks an hour. I was talking to a guy that was waiting to have something for him cut and I had him laugh and I said oh yeah they'll hire anybody if you got experience. You got experience in in carpentry? Yeah sure I built a birdhouse back in the Boy Scouts once. You're hired. You know that's pretty much it. Okay guys enough of the rant. Let's move on to getting this set up. I'll put a clamp on here like I said to hold that. Maybe raise this up just a little bit. It's already up so all right and again I'm gonna keep doing that I'm gonna get my hose drilled and I'll be back with you and show you what I'm gonna do up here. Okay so I got this in here it's straight it just kind of looks funny because it's at an angle there. So let's measure this and I'm gonna measure up to the top of this because this is gonna be recessed just a smidge in there so should be about three inches ish. Can you guys see that perfect three inches? So I'm gonna cut all these off at three inches and then I'm gonna drill the rest of my holes. Okay so I had to go get a new cutoff wheel because Monkey used my cutoff wheel last week was it to cut some copper? Check that out. Look at that. We're down to the mash. So how do you do that cutting copper? So anyway I went and bought I bought two cutoff wheels and a flapper disc. I already got this one on here now so I had it. Which brings me to a good point. I had a comment here it wasn't too long ago but I did I deleted these comment because this guy was an absolute idiot and said I noticed you have a patreon page and I noticed you're monetized what do you need money for it doesn't cost anything to film. Okay right doesn't cost anything. These two cutoff wheels right here and this flapper disc right here $21 almost 22 bucks doesn't cost anything to make these videos. No idiots like I just oh they make me mad. So I'm gonna go ahead I'm gonna cut these off and then I'll finish drilling my holes and like I said I'll show you how I'm gonna make that set flat into the wood. Okay so I'll just speed you up through this it's kind of boring just cutting stuff so let me get you moved around in a different angle let's cut some of these off and I got to go and have to get two more three more so alright guys and there we go. Now I'm just gonna take my little pencil here just gonna mark this around here now I don't have to mark the holes because these are going to go into the wall so and I'm just gonna take a chisel and kind of chisel this out let me go get a chisel I'll do this one for you and then I'll just go ahead and finish the other stuff off camera because it's all gonna be a repeat. Okay ain't the prettiest but I'm not a carpenter. Here we go awesome okay three more to do I'll spare you a half and watch that again because like I said just a repeat so let me get going on them make some holes we're gonna put our hardware in there we'll get this side on then that way I can go over I got marks on that board where the other side is going to be and we'll slide it off do the same thing as we did on this side and we'll do the same thing on this side as I did over here I won't bore you with that but I'll bring you back when we're sliding this on I'm not gonna bore you with it I'll bring you back once I get it on there and we should be good to go all right time to get some cameras okay guys so there it is there's 18 up there that's not counting of course the one I'm using that's not counting my body camera because I got them in a different bag so that way if I want to go I can take off and go I also have a little tiny spy camera they call it a little cube it's not up there it's in another bag and I have I have like two two or three that are for parts that I don't have up there because you know one of them I took apart you guys saw it was just unfixable so it's not gonna be up there a couple of those over here quit working that JVC with the light I think it stopped working and one of the other ones beside it stopped working that one beside that black JVC that's for dads it does work somewhat records audio no video all of these did work at one time that one up there second from the right on the top shelf that's from the 70s I can't remember what year it is but it's from the early 70s and it's just you put batteries in it you squeeze the trigger there's no sound or anything so it's an old vintage one that RCA is kind of cool up there and a couple of them don't work anymore but that's okay it's my collection when I buy them I don't care if they do or not so that looks pretty cool up there and I love each and every one of them but there are some up there that I can just reach up and grab the one on the right that sharp it works the old one works there's my my GoPro cheat go version of GoPro it works the one besides its her dads it doesn't work it's got issues but it looks nice the third one down on the bottom third one from the right it works flawlessly it just it's 720 it's not you know 1080 or anything like that but it does work the one besides it's old blue the one beside that works the one beside that the Canon I believe it is one of them to their work it's got night vision we use it for like ghost stuff so and I also have my other ax Sony ax 53 that I got to have repaired the screens messed up on it so I'm trying to find somebody I can send it to and repair it so I got that one I think I got another one in the garage I'll have to go check let me check on that okay and we also got this cheap and or whatever it was like 200 bucks you got a whole bunch of stuff this is a the first brand new camera we bought together and believe it or not it still works it's all kind of but it does still work batteries probably dead right now but this would this would be good to set outside or something if I wanted to to record something I moved old blue down there I'll set this one up here yeah this one here still works this one I was telling you has night vision I believe it may kick on right now if the battery is not dead I think battery is dead okay yeah so the battery is dead on it I could charge the battery I made some batteries for this thing so there's that all right cool okay guys so there's my collection you know it's a cheap collection but it's mine and I like it turning around all right let's back out a little bit here okay so there's my collection guys and there's our shelves I think it matched pretty good with the my desk there and the rest of the bedroom suit looks identical to this so it all matches well so anyway guys thanks for watching there's there's my cameras like I said I have a couple more but the X 53 I do want to have it fixed that's the same one I'm using right now I want to get it fixed and yeah if I got several but it's just my little collection I've got not counting that one I just put up that monkey not bought brand new not counting that one all the cameras up there minus that one even the GoPro all put together I've got around 50 bucks and all them so it's a collection I don't care if they work or not it's great to be able to I know which one like that one on the end works and one of those two work both of them work I do know the JBC don't so the two on the end work one of those kind of acts funny works once in a while so like I said that one there works that one works that one works that works that one works that one works that one works so you know it's just my my little collection I like it some guys you know collect cars well I don't have the room or the money to do that so I can afford this like I said there's about I got about 50 bucks and all and most of them have cases so in the cases are you know nice cases this is for that third one over from the right so it's a nice case hardly ever been used they just stuck the camera in there and that's it so yeah I've got some nice cases here this is a nice case I mean those you know those alone to me you know there were five bucks a piece then I got these for the big ones there's one and I got two here this one it's got keys to it this one down here it has keys to it and I have another case in there that that one of one of them go in so those are those three big ones there so anyway guys she bird met the man legend thanks for watching thanks for helping me out on the shelves I appreciate it I think it looks pretty good excuse me now I can sit here and look up at my little my little treasures so I got to get a drink I'll see you guys in the next one thanks again guys I appreciate it she bird met the man legend gone for now and guys stay safe alright we'll see you soon bye bye