 629 it's Wapping 82 degrees outside, so got a call. I'm a swapped call with somebody So let's go in here and see what's going on with this air conditioner It said the dining room is not working So I'm sure it's probably Something stupid I hope probably dirty Or whatever Get going and see what we find I cannot believe this meter bag three man. I just absolutely It's been doing awesome. It has been doing awesome. It's so small. I mean, I love my bag here They got but man, it's thinks so much easier. So anyhow, let's go All right, I think it's pumping the heat out oils luckily are clean I've cleaned these before These are three layers thick massive pain in the butt over here was the worst I don't think it's an air flow issue See whether or not we're getting condensation very well This is not the greatest deal here Which surprised me the belts probably loose Wow, we are well out some massive condensation Well, when in doubt, let's check the belt And our builders probably one of the most common things is a freaking belt Meow Let's see if I'm tightening these up Checking filters. Oh Geez really? Idol are Poli's not too bad freaking She their war Really nice Yeah, they're war pretty good Like I said that freaking Poli there man. That's That's a major freaking wear on it. Yeah, this other one looks yeah, I mean, it's not horrible, but it definitely Definitely probably another month Maybe two months max. It's gonna need it I don't know whatever it is it don't seem to fit very good one other thing I want to check real quick Make sure this isn't sucking a crap load of outside air in Which a little hard to see on this one Should probably done this with a filler door off, but whatever It needs a job And a little better. Let's see if the compressors are all running. It's pulling really hard on that door Only one contactor is pulling in right now. I'll hide the stats cranked up You should be a two-stay stat on it because the other one this one here is doing its job as best it can calibrated hands we're not going for The full pony show today. We're just trying to get him going and always come back later It all seems to be working This belt wouldn't surprise me. Now. Let's go check that other one out Only one benefit to being up here on this section going up here and So you can find the other one I think it's Trying to remember where it's at Oh, I think I remember it's on the Backside of the building here lots of heat there and it's slippery belts, but it's running They take care of a lot of this themselves Yep, there's the other one. So I think that one there does the kitchen now. It's cranking out some water too You can see it. I have a good idea when you see water Dripping out of the bottom of the unit They ain't good because they're watching that musical group stomp Where they play the trash Trash cans have a feeling it's the same ordeal here. Let's check these belts same freaking thing Filters look good Automizers clothes drain pan is nasty is all get out Just one blower. They plugged up the scum That's what it looks like to me then blast that thing out, but all we can do I don't think I can get this part Sometimes they don't glue it, but you can see there we go. There's a little slime. There we go Possible some goodness for everybody Look at that. Heck. Yes Something satisfying about seeing that come out. Not sure what it is, but it just is Now that's gonna help out quite a bit there. That really needs flushed out with the garden hose Pan needs flushed out because all that slime It's just gonna get hot in there and you can see That stuff is disgusting. We've got two compressors on this one So we're good on that putters this one right here We're at 11.6 amps There's something kind of cool about this one Run right at 60 Hertz So they can do that with freak drive Accurately that's the key accurately so 11 and a half 10.2 So it's it's over real close to that like magnetic coil It'll throw your clamp off. The fluke's pretty good about not doing it But it definitely can happen. I'm gonna pull it away from it Pretty sure this does not have a capacitor for that blower motor I only see two legs I have a feeling there. Yeah, there it is the black. I think they took one of the legs and bypassed the Contactor and just went hot with one leg Let's make sure here Yeah, I made it pretty tight so might loosen that up touch Uh Yeah, it's three phase What sucks is I hoping that up God it's already freaking about as far as it can go Yeah, and the blower wheels I've seen worse, but man, oh man Look down through the heat exchanger and stuff Here's that nasty pan. It ain't so bad over here. Mainly got it right here on that section There's all right here Loosen this up a touch. It's a little tight Their instructions usually tell you just to tighten it up enough that it doesn't squawk when it comes on Same freaking thing It's four inch pulley. Here's another little check for you. So back and forth. We're good. Listen to this This motor is going out. I know how this will go So they'll wait until it's completely gone. Unfortunately Get it too tight, that's what takes out these bearings and everything else that and just age is what we got going on here Gonna get my information off the motor They definitely need a pulley It's pretty tight, but I don't know at this point All of our compressors are running everything looks pretty good Blower wheels all that stuff all that ain't happening today. We just got to get them going. This is this is ambulance coming in Getting the patient on the gurney and out the door to the hospital We're not gonna go for Perfect brain surgery or all that crap There's the information for that. All right, I don't suspect this is gonna make a humongous deal. Just kicked on didn't squawk I'm an idiot. That's a compressor. Oh my god All right. Well, let's look at this one here. All right. We're only pulling five 5.5 amps, so we're nowhere near it. Let's uh, let's speed that sucker up a little bit So try hitting it some heat see if we can get it out of there That pulling each changed anyway, so if I can't get this we're gonna get it going They're already dying so bad that they opened up the door for the kitchen and it wasn't that bad in there All right, could not get that loose pulling needs replaced either way We're just gonna have to get it up and going away. They had it. Let's go see what we're getting on the inside now that it's been run I think Just the second stage came on. So let's go to the front where we were first at All right, so We got 67 back here, and I've had as low as 66 It's 89 going in on the return Out in the dining room. We've got 72 going in and 57 coming out. We got what 15 degrees there and 23 degrees air. So obviously the fan speed needs to speed up for the kitchen. You can see with that Grill there is just a mat. So we're back out here at the kitchen Just wanted to see if my laser thermometer is accurate 88 and a half degrees coming in not going near as fast as what it needs to be going 62.6. Let's just take it to 62.5 All right, so we got 26 degree delta T. We're nowhere near as fast as what we should be going with that fan Problem is that that pulley is jacked and it's war so it probably worked really good when it was first installed Now that it's all wore down from everybody letting the belts go loose You know, it's not doing its job. It's not moving the air and getting rid of the sensible heat We're definitely removing the humidity Which is a little difficult to do in your drain pans full of water But now that we've got that pan drained out That's gonna help that out a little bit and that belt being loose. I mean it makes a huge difference I've seen it time and time again. You're like, well, that's the only thing just a little bit loose So yeah, you can see it's doing pretty good So I didn't do a temperature drop. Well, yeah, I did on the other one So that's 15 degrees in the dining room 15 degrees on the dining So that one's a little more respectable So I'm gonna let them know here in a minute give them a call and let them know what's going on But it's doing as good as it can do for right now. It'd be a lot better if that fan was going a little faster