 Okay guys, so now we're just gonna go for a quick go through the modes, okay? Now I'm not gonna go through every switch set up with you at this We'll do a different video on switches and their their link to the mode. We're just gonna go through the modes My switch is already pre-set up for different things. So Okay, so as you can hear I've assigned Some speech to the switch I've also assigned He says Just do that I'll just disassign that that switch by hitting the safe as I already taken out the arm But we're gonna redo that again in a minute Okay, so you can hear horizon mode So there we're gonna be putting two things together when I go into acro mode I'm also gonna be going to air mode and then because they can be a little bit of a problem when you're landing in air mode I'm gonna be able to switch Horizon mode, which will turn air mode off and I'll And we'll put that through as well. We'll set that up in the sounds. So to start off with them Let's just do the arm. So here you got arm now. You gotta remember you've got I Don't which order these go around a week. You can just think about it like this. We got like one two three four, okay So those four channels are being used so every channel after that I've got 12 channels On the particular receiver I'm using and so every channel after that will go five six seven eight nine ten eleven twelve Twelve is being used already for the RSSI and link quality combined on this I have it that whichever is the lowest indicates to me, whichever is the lowest, okay? So let's set up the first one so for We're gonna add a range and automatically it's called with channel five, which is fantastic And we're going to decide When we see this little marker be moved This is all disabled and the only place that it is where it's armed. I'll just move my arm Is there so in this area here where it's blue little blue marker goes is where it's going to become active And that's where it will be engines armed There's a little bit to go into about pulling your armed on that switch and what we can do about some of the things that can happen go wrong if you Accidentally flip that off, but that's a different Video, so we're gonna put that there. We know that works there as we can see it And now we're gonna go for angle mode now, of course We can't use channel five because channel five we're using already and if we were to move that across You'll see that move there For channel five now This is gonna really work out well for us when we come in to add in a couple of modes to a single switch Or a partial movement on a single switch So switch that off now we want to go for the next one and on this for me. I've set mine up to be channel six This is where I get to shift between the moment Not rate so If I move if I've put this to channel six and cause my switch, I've already set up the channel six you can see there It moves cross once And then into the middle for horizon And then we go to nothing now which defaults it to accurate, okay so because I want to do the horizon the Auto level and angle mode. I know mindset is cheap mode It's because just it's just there there's a whole sound packet You can choose from the sounds that you want to put in there and I put cheap mode on I shouldn't have it as cheap mode Really, it's just angle mode which angle mode is where you've hot you've hardly got any movement left and right You can hit the stick for what but it only moves it very slightly Which is all well and good when you first have me go and just trying to hover floats around just Get used to the sensitivity of the sticks a little bit But once you start flying a bit you really want to have you know as much movement as you can So channel six again for angle mode and again, we're gonna add another range for horizon mode here We're also going to give that channel six Because we're working with channel six so if we Go to horizon mode you see now this blue areas little just made that a little bit wider This blue areas make it up And then to angle mode that's there and then when I go to It's gonna go into the default position Of nothing and that automatically puts on to acro. So if you don't have these set up you will automatically go into acro As the default thing Now I also want air mode to come on and go off. I Want it to come on when I go into acro and I want it to switch off when I switch back into horizon for landing Okay, it's just gonna make landing easier for me So again, we want to use channel six because that's the switch that I want to use to control this mode So we're gonna go to channel six We already know that when we're in acro on the angle and horizon It means that there's nothing there. So I'm gonna move air mode into this space where there's nothing there Now what's gonna happen is when I go to horizon you'll see even with air mode Horizon mode air modes off because it's the blue line here that indicates the active on all these Wherever this is is where your mode is active in this blue line So I'm gonna pop that like that and then when I want to go into a Okay, so we go into acro mode and air mode comes on automatically So now I can go and do some fancy stuff hit that Throttle all the way off knowing that even though the motors reduced down a hell of a lot. I've still got pit control So we're not just gonna flap out the place and do what yeah Do you know do what you can you can see that happens with a lot of cock up to be just hit the throttle straight off You know, they just wobble all the way down to the ground and not really good at all Okay, so that's that switch now. This is what you're gonna do for the whole lot. So we've got another one here All right, I can't remember what that is What we're gonna think about now is the things that we want on this and one of the things that we want to push at the moment on this is Return to home and position holes. Okay, so on over on the other side here This is where I've got mine, you know, you can set up your switches on whichever ones you like how you like It's up to you. You could put them on to these variable potential meters if you like Might be better off if you were controlling the camera with these or you know, whatever But let's just go to a let's just skip down a whole bunch of these things Even go to another nav position hold and we're also going to look for nav return to home So this is the next one that we want to use now if if you use in one of these radios You do have Sorry You do have on the front. I hope you can see this But you get to see If you see that move down there And now there gives you the number of the channel so if I were to Now I don't like the way two of these are going for this That looks like there's a little bit of a An upset Okay, I'm just checking that that's okay I've just put a mode on there as well for something else Sometimes when you update these and even though you copy your models across it's always good to check that all your all your channels They're still doing what they're supposed to be doing because sometimes, you know, things can Things don't always go the way you plan So what I'm gonna do now is I'm just gonna quick look at that and just see what channel that was that was channel 11 and 12 Okay, so I'm quite happy to use channel 11 because I know my channel 12 is actually being used for our SSI Yeah, so what I'll do is I'll go into into the channel settings and I'll show you how to do that in a different video I'm going to the channel settings and we'll just go through our channels and just ensure that we've not got those people overlapping Because you really don't want that like that, but just for this little experiment because it's only on the RSSI I'm not gonna be bothered to put it too much about it. I know which time I want to use that needs to use channel 11 Because like I say I'm already using channel 12 For my RSSI because you have to give it a channel We're also going to use a position hold on channel 11 as well Now the only difference is here now is I know that if I push the push the Switch forward that's my position hold and if I look at it like this is when I want it to come home I want it to come back to me So the switch comes back to me Return to home and I can see here now that return to home is over here Because the little blue mark is there. I switch back That's off. We're not we're not doing a position hold and we're not doing return to home Push forward. I know now to put my position hold there Okay, so we can just save that like that So now I know I've used channel 11. I know I've used channel 5 channel 6 and I've got one two three four five six about six controls and I've used one two Three channels Okay Which is pretty good because there's gonna be other things that we want to be able to do like we want to be able to do altitude hold And my altitude hold if I remember rightly He's on this switch here Not one there He's saying it's channel channel 10 and channel 13 so When I did the update on this what I've been doing this that has been some some mistakes, mate Now the nice thing about it because we're saved I can just Switch that off because that's the beacon. I'll show you you can set those you can change the timing on them and The volume on them as well That's a different video So we also want to make sure because we want to do some things with this so a Beeper we want the beeper because we want the lost alarm the My beeper here is on channel seven So now we know we use five six and seven the beeper uses an entire Unfortunately use an entire channel to itself All right now if I just say that Okay So if I'm up in the tree or it's in a bush or it's in some long grass I'm not quite sure it is and I don't want to wait for the beacons to go off on the ESC's I can just And get an audio an audio sound Yeah So that does come in really handy It does come in and really handy. You don't have to use it You could just wait for the charms and if we do run out of channels and we need other channels to do things Well, that's exactly what we're gonna have to do So let me just set up and I know that I've got to go in and clean up as well But let me just set up the altitude hold Why did I just see that? altitude hold altitude hold altitude hold Because we've also got down here look see this the on-screen display I showed you before you can have three different on-screen displays if you want so you can put them on to a switch You could even set up your on-screen display. So you have a different one for angle Yeah, you can have a different on-screen display for horizon and a different one again when you're in down here on the switch on this particular switch for Acro so with me in acro I'd have the least amount of information on there because you Don't really want to be looking at that. But if I was in horizon, I'd probably want the same a Lot more information in there maybe But you you don't have to find another switch you can You know add to the actual channel number and get the switch to control that mode as well That's where you can start, you know, but doing a bit of like a They're coming through with the old modes and switches. So So for the altitude hold I'm gonna put that on channel 10 I know I'm gonna go and clean it up because it's also been activated with the just check that again channel 13 which really it's not gonna affect this because this receiver This receiver only has 12 12 channels, but still I prefer to go in there in the software in here and clean that up So we got altitude hold there Now we've got to figure out now what else we can put on without you hold so what else we've got we've got a Turn assist doesn't really come into it with us. That's more fixed wing heading hold again I don't Know I don't suppose you can really use heading holds on a quad Particularly, I mean, I suppose it turns but you normally be manually flying it Whether you've got altitude hold on what is a different thing this surface thing This I think is if you've got a sensor so you can actually sense the distance between the surface Let's say if you wanted to do it The 400 feet because you're gonna remember if let's say you take off from here Or where can you see better? So let's say if you take off from here and then you're allowed to go to 400 feet Right, but if you take off from here and then you come across here You're no longer 400 feet from what's below you so you're allowed to go 400 feet Above this then you've got a little bit of time to bring yourself back down again to 400 feet And I think with these surfacing's that's that's what helps with that Well, we've got to make sure that we've got a switch because I don't use things like home reset That switch would be let's say if you were flying about and then for some reason I don't know really drop the thumb ahead why you'd want to use this But for some reason you decide that you want your home point where the GPS Located you as home when you first plug in When you when you first power up your quad It's gonna use the satellite receiver To take your GPS location and lock that to your home position. Okay, so then when you're flying out there And you want to return to home It knows to come back to where you powered up from basically to where it first took the odd GPS location Now there's a little bit of a mess up with that or can be if you could be flying Let's say with fixed wing more so than a quads because with a quad you're gonna fall like a brick out the sky You could be flying with fixed wing and just accidentally. I've done it before just put my radio down and it's not switch off And now when I turn it back on again It sets the home position to where ever the craft was at the time And so if you're flying somewhere, you don't really know that well and you you kind of a bit of a pickle You do a return to home It's gonna fly back to where you switched on Your switch and I'll show you a bit of code that you can use for that on a different one But actually do that about this particular switch Where you can decide to Set it so it doesn't happen like that So me I have mine set up and I'll show you on On this it's only when I power it then it takes the home position. It won't do it any other time It's only when I cycle this power this it did sign on off once it's locked in there It doesn't matter whether this goes on and off It keeps the home position that I first set up on it because you know chances are I'm still in that position Okay, so We've got a we've got a position hold We've got a return to home. We've got our altitude hold now This would be because if it was set up on a If it if it was set up on it on a fixed wing Now I am wondering whether it's of any use to me on there. I don't know But if it's not then you know, I'm gonna be using one of these other switches to set up my waypoints Because I don't I want to be practicing around with these waypoint missions I don't want to keep saying program around a few people the last few days. I've been talking like that. So and I Want to be playing around with the waypoint missions Just see you know, just see what we can do with this now this FPV angle mix Not even quite sure what that's about but this is a Camera stabilization servicing. We talked about home. We said we talked about GCS map Don't know what that is MC breakings this is motors breaking File safe that's always good if you want to chuck it into a file safe But generally if you've got return to home, you know, you can put the file safe on your return to home So, you know if you're gonna get into problems you just Sorry Flip your return to home and that is your file safe in a way and it's also your file safe as well when we go into the settings For You're actually getting back and that's something we're gonna look at in a second actually so we may want to adjust the on-screen display as I said, you got a choice of three on this when you set up your on-screen display and You can put them onto your difference T different modes here for angle horizon and of course when you're down here like I said before your acro mode Camera controls you're probably more gonna find that, you know, you've got cameras on your Obviously much bigger quad in this or a hexcopter octocopter Or or an airplane, you know, whether it be a wing or just a fixed wing Fixing so camera controls fell safe kill switch Not sure what you might want that for and the on-screen display switches I have to look into that why you want to use that Pretty sure that on my on-screen display switch when I was using the little minimum OSDs There was a way of having the on-screen display switch on there And you wouldn't use it through here because this is This is using it through the firmware here when you get to see the on-screen display And we'll do a setup like that and we'll switch them between up as well It's not set up now. We don't know video. So as for modes, let me just go into a quick advanced tune and Oh, sorry Onto a file safe and now you see instead of it, but you can have it so it drops out the air You can have it so it lands You have it so it turns home. I'm gonna put mine on so it returns the home. Yeah, I wouldn't have this do nothing Now let's look at what it say here use alternative minimum distance file safe procedure when close to home And I think that's just a separate switch For doing this so you've got a different file file safe procedure because I think it only will do When you're a certain distance away the return to homes Okay, and I think this is a This is the delay for turning off the motors, but that's a different thing. This is a different video Okay, because there's quite a few bits bits and pieces going on this But I'd normally have that set to there. So I'm just gonna go back to those modes I don't know so that's it That's easy enough isn't it set up your modes and you can see that you can add I'm gonna do this here now I'm gonna add for the camera. So we're using channel six. We know that this one down here is our angle We know the middle is horizon and we know the edges acro. So just for the sake of it. I'm gonna go into here We're gonna use channel six And we're gonna go So on screen display What is one it's one for the alternative and then channel six again And then we're gonna have this in for horizon Okay, and then we're gonna have Down here For a quote. Okay, so now you'll get to see as I shift this switch here these will switch as well Not quite. Oh, sorry It's not on the right channel. There we go. It's on channel six. So let's put that back So we'll have a mode come on when we're in acro. We'll have on-screen display Three come on when we're in acro and then when we go to horizon that will switch off and This alternate on-screen display will come on when we're in horizon And this now you remember these could be exactly the same that could just have nothing on it You can do that however you like And the way you set them up and we'll go through how you can do that as well But just for now we can see now that we can control Not only a mode for the one switch not only the modes with the one switch But also on-screen displays with that one switch. Okay, right. That's it for the end of this video and We're gonna look at the magnetometer No, that's it for the end of this video guys and Stay safe and I'll see you in the next one