 I didn't notice that that popped up down there before okay good on it so let's uh now let's go put back into our system the old stiley because i know that that was working fine for me i didn't have any issues with it whatsoever okay let's calculate the space install yep finish okay now i'm gonna have a little quick look in the uh c drive into the 86 into the stm st mark electronics and then here we have it again look so i'm gonna go ahead and install that again because you're going to need to do that chances are i don't know it said there it's ready to use now so now here is the moment of truth you shall open up i know 2.5 what targets you don't hopefully that's not made really any difference to this so i'm just going to plug this back in again and we're back up in dfu so now i've already chosen the board here i'm going to choose the very latest and greatest firmware for it so you're getting to see we've got mattock f405 that's i'm pretty sure that's what it's saying for us to choose here mattock f405 target that's what we want so let's go back here we're going to load the firmware just collecting it from the internet i could go and find the hex i suppose and just download it so i've got it but just for this now we're fine um if you want to read through this you can read through that and now we're going to flush the firmware okay so we're going to erase this first lot as you can see we've started out the little one LED on it's erasing what does it say here what fixes have we got fix editing negative survey weight okay vscms fix and overflow in on-screen display code okay it tells you what to do if you've come into issues why are you trying to do your thing okay there's a very there's still time removing boot jumpers here so this will only take a few moments quick verify okay we're good programming successful it's about to be booting itself i'm just going to disconnect that i'm going to flick across the welcome screen reconnect that and this time this time we shouldn't have any issues okay right so we're going to leave that same mini quad again ah this time look we don't have the uh the issue with that so let's let's see i expect to find one issue because i think if it's going to keep hold of the old note it's shifted itself the accelerometer and now we don't have a calibrated accelerometer but it's happy with the hardware it's happy with the hardware on that gyro it's happy with all the hardware on this verse far so let's go to that to the good old calibration again my rights after all this time you should know how to do the calibration right and so should i it really does help if you get that hex sorted out the start remember it is quite hard to mess these up because it is held in wrong and it will re erase and flash again so let's do it again then so this time let's just hold it down nice and flat again like so pretty much flat i mean never going to get it absolutely right anyway unless you've really planned out this so let it process what i'm holding it flat there we go we got a tick i do like to see that tick i was going to say i'm sure we've got this sorted out so we're going to kind of write this one but while we got a tick there and i'm going to show you how it doesn't matter which way we go around now because i'm not going to do it in the correct order this should be the one facing down was the last one and then we're going to do it in this order here which i don't know which one it is now probably good you know to do it in the right order but um facing down we got that one so we want to be facing upwards from this one then just hold that there so i should give us this one i don't want to point into that and then of course the last and least is this one and this is where my fingers are trembling a little tiny bit slow that down calibration finished okay there you go to check the values have been saved yeah two twenty ones but never mind so let's just review that now and we will get to see very quickly if we are okay if we were successful with that okay so we're going to go back to our set up and yep we're a bit obscurvy so where's the arrow that'll be the arrow or bump right so let me just put that back there so forward backwards left and right okay doki so we've got that pretty much in now we're going to go from our calibration which we've just been we're going to go to our mixer now we're going to tell it's a multi rotor yep there's your options airplane try copter a rover boat or other we're going to go for the multi rotor it's a quad X that I've ordered a different all that lot we're going to load load and apply like just load in the mix so we're going to load it and apply it because we know this is what we need in there okay doki so that's here so now it knows what it is we're going to look back at the setup again and as you can see it now knows it is a quad it knows it's a multi rotor and it's happy to get going so we've done the mixer let's have a look at the outputs not really going to change anything here just yet um we are going to probably look to set up our D-Shot 600 as long as my ESEs allow me to go that far with it I need to check that first so this one's going to leave for now in the presets here because it's that the 600 thing let's just leave that for a moment let's leave this let's look at that as that was a great way to learn how to set that up and to get it working correctly okay so we're going to call that the the fumbling but we get there eventually setup of the of the thingy why it's good to choose the correct hex all right guys just for that then we're going to leave that as that and then we're going down to the next bit once I've done a little bit of nosing up on my ESEs and what we can do with them and what we can't do with them I'll catch you in the next one take care