 Hey everybody, GeoArm Security here, and today we're going to show you how to install the M2M services LTE-MAV wireless LTE M1 cellular alarm communicator into the DSC power series system. Now a quick note about this M1 LTE module is it's perfect for anybody coming from next alarm services or looking into a ring or a simply safe system. The reason why is you can reuse your existing system in most cases, only pay about $70 for the part and have a monthly monitoring rate with GeoArm for only $12 a month with no long-term contract. In addition to the low cost of the module as well as the $12 a month monitoring, the M2M module has another advantage which is it comes pre-wired. Now in this first part of the video or the first segment of the video I'm going to show you how to wire this just for basic wireless signal forwarding meaning no app control from the smartphone. In my second half of the video I'll show you what you need to do with the orange and the white wire. So for now you can put those to the side and you'll just be working with the green, the yellow, the black, and the red wire. These four wires super simple. Okay now key note here is make sure the backup battery is unplugged as well as the power transformer. You'll need a small flathead screwdriver. Okay now this is very very important and I'm going to show you the first wire we're going to work with is the red wire and usually that means power same in this case. We're going to locate the auxiliary plus. Now it must go in there because there is polarity so if you you know switch to these wires and you put black here instead of red you could fry the module. So what I'm going to do is unscrew auxiliary plus, insert the wire, tighten it up that way it doesn't pop out and you don't have any communication issues. Now I'm going to go ahead and go with the black wire which is going to go in the auxiliary minus simply unscrew. This is what's going to provide power to them to the LTE radio. Okay now we're going to work with the green wire and green is going to go to ring which is clearly labeled right here ring unscrew it insert and tighten very good. All right last but not least we're going to locate the tip port and we're going to wire that in there tighten it up. So just to confirm we've got red in the plus black in the minus green in the ring and yellow in the tip. Now we're going to get our antenna out of the packaging by factory it comes with a three foot antenna if you needed a ten foot when you're ordering with the link below in the description there will be a tab so you can toggle between the three foot or a ten foot and this is super easy what I like to do is just go ahead and mount the antenna here go ahead and feed the wire through we need to screw that in and if you like you can just place this LTE module inside here you can use 3M sticky tape double-sided tape whatever works make sure that the orange and the white wires are out of the way and another key note about this M2M LTE module is that it can actually work with with your alarm system even if you don't have your installer code in most cases there's three questions that you need to ask yourself one has the system been monitored before two do you have the codes to arm it and disarm it and three is it in working order if your answer is yes to all three of those questions then this module can send your alarm signals to our central station receiver without the installer code now you'd go ahead and plug in the backup battery and the power transformer and give geo arm a call so that we can go ahead and activate your monitoring services stay tuned for the second half where I'm going to show you how to wire the orange and the white wire so that you can control your your alarm system from your smartphone using the R control app as promised I am going to show you how to wire your power series with the M2M module for interactive remote control using the R control app the first wire I'm going to work with is the white one that's going to be assigned either to pgm1 or pgm2 in this case we have a brand new board and I have pgm1 open I'm going to go ahead and screw that in there make sure it's tight it doesn't come out and you could use pgm2 just make sure you tell your tech when you're getting this thing activated so that way they can assign you assign it in the keypad here a quick bit of information you'll actually need your installer code in order to get the interactive app if you don't have the installer code to access programming then you you know you're not going to be able to get the app on your smartphone so keep that in mind now you'll notice with the orange wire I've just you know simply twisted together a 4.6k resistor which will either go into zone one two three four five or six whichever one you have available you will need an open available zone dedicated to this wire or else it won't work so I'm going to just go ahead and use zone one I'm going to screw that in there make sure that it is secure then I'll take the other end of the resistor and wire that into the common right here open it up a little bit and it's in there snug and I'll go ahead and screw that in there nice and snug so you'll see zone one has one end of the resistor as well as the orange wire and the other area the common has the opposite end of this resistor wired into there okay and at this point you can go ahead and plug the backup battery and plug the transformer in and if this is a new activation you can call georms so that we're able to activate the radio by the way the username and login for the app to our control is actually listed inside the instructions which come in every package which is uh identifiable by each individual communicator make sure to subscribe to our youtube page and click the show more tab underneath the video where you can view valuable links pertaining to this product similar how-to videos and our low-cost no contract alarm monitoring services