 Good morning guys. We're back. You got some help in the form of a Lucas You should see Lucas's reaction when you look at the frame. He's like, hmm Decent decent Okay, so today's plan is to wrap it up a little bit more because I don't like this dirt that's still on here you can Tell by my you know on my fingers the dirt The dirt so preparation is key decided Not to chase he savor the whole thing just the black stuff, which means well most of it really the frame the Everything else black basically More control arms all the suspension components does this subframe the frame Mainframe and all all this right like maybe even a sway bar this this guy I actually have this stuff. I can show you finally. So this is it. This is the chassis saver if the Surface is painted then it needs to be sanded down a little bit scruff You know scruff scuffed scuffed up a little bit with 50 60 grid just so it has something to stick on and Then on the inside and outside underneath the floor We're gonna use this. This is by Emsio. That's the wax stuff. I mentioned yesterday and That that's the light. This is the last step. So we got some cups We got gloves. We have this these Got paper. We're gonna actually when we're done scuffing it up with These guys this is 80 grid close enough. This will get us Into the hard to get Engeled Places you don't mix the chest or don't shake the chest saver you mix it stir it And this is what I'm talking about. These are the ones Hopefully I can attach it somehow to the can spray can and Spray inside inside the frame and the floor and all that stuff and this is just a degreaser and We've got some Brushes I guess we're gonna scuff it up Clean it. I'm gonna go through the frame again. I'm gonna still gonna Blow air Inside the frame just check make sure there's no water inside and Lay the first coat on okay guys. We are ready to paint Look is degreasing the fuel tank cover The frame looks pretty much the same It's just squeaky clean so clean you can eat off of it clearing the The axle here the back plates Everything the drive shaft the floor Scuffed up and cleaned okay. I'm gonna get ready to paint basically what I'm gonna do open up the can Steer it slowly as the instructions say and Start painting all right guys. We had a slight situation our Cups melted Okay, so don't use those Luckily for us. There's a Home Depot next door literary walking distance hopefully these will hold up and Yeah, let's see Yes, I did Look is taking a break didn't get far This is what it looks like it goes on thick Make sure you don't go thick just dip the brush in the paint a little bit and spread it out Thick coats will bubble up now from my understanding This paint dries To humidity it mixes humidity dries it up. So if it's a humid day It's gonna dry up quick which is which is a no-no Wanted to be a Regular human day, I guess if you're in Florida, we're gonna wait till wintertime. I guess Okay, we're gonna continue This is gonna be a while Especially if we get the two colds All right guys we got an update. Hey, how long has it been? Three hours two hours I'm thinking maybe two and a half hours It took us two and a half hours to paint this. Let me show you check it out It's it's shiny because it's still wet Takes a few hours But I Did paint Remember we had that vegetation a lot of it just behind this fender plastic here so I painted that too just as far as I could and And right up there. This is this was the oh still have We're gonna have to do some touch up Little more touch up there Check this out. I Know, you know the threads on the bolts and whatnot break lines, whatever I mean if you want to keep it clean that you just gonna take you a week to with a little paintbrush To do a nice job. Just you know collateral damage, whatever doesn't matter I'd rather have it painted Than than rusted I also painted this inside here all the way all around Because dirt collects on the inside there And you can see if it's not scuffed you can see how the paint does not stick What else wrong with the camera? Okay, I don't know why it's flickering, but anyways you can see the white lines that paint was not scuffed and it's Not sticking to it, but this doesn't matter. I wanted to just paint it on the inside there. Let's take a look underneath It is nice Okay, it's shiny like I said because it's still drying And you can see I mean over brushing everywhere exhaust whatever From portion of a differential which is oh, yeah, so that's why you don't see all those Yeah, check this out No, it's it's Yeah, it's it's cast iron. Yeah, that's why everything else is smooth drive shaft Now obviously there are spots we didn't couldn't get to like for example Up there Little bit. Is this light dying? He was like this dying Anyways, we're gonna come back. All right, we're gonna we're gonna go eat Give it an hour or two dry up Also painted this on one side only and then just go over decided to do one one coat Because since I'm gonna be spraying that the wax thing You know and it wasn't rusty One cold should be yeah, it wasn't rusty you one coat should be sufficient So we're gonna let it dry Relax a little bit breathe fresh air Should be wearing masks Trying to get this stuff on your skin if you do watch or Use paper towel, whatever watch it off right away Degreaser works well on it does on skin Anyways, like I said Third time we're gonna let it dry and then we can kind of get in up, you know Into the nooks and crannies up in there everywhere do a little touch-up so we don't get dirty And then let it dry. What time is it anyways? I Don't know looks like four o'clock p.m. Or something like that I'm gonna come back after the chat touch up Five five, okay We'll see. All right guys. See you later We're gonna start spraying but we're not gonna spray the frame just yet because it's still wet. I'm gonna wait I don't know maybe Two days or so For it to fully dry They start not to spray the inside of the frame yet because it might drip down and you don't know their reaction of the tool when they're wet So that's gonna have to wait Inside of the frame and stuff, but Let's not go in but we can spray this On the paint the floor the paint. I'm gonna start with the pinch welds here No, hold on. I got your Sorry, yeah, okay. Thank you for some gloves. We're the struggle All this sort of stuff What? Seriously, that's not even staying in what the hell I'm soil Man So this is Why the ones because I need the straw To stay in there to hook it up to the one. Yeah to hook up the one Okay, I did spray a little bit on the black paint Do not catch a fire So spray inside the pinch weld there Just kind of People don't don't don't see you they just see I'm not gonna explain so there are hope what was a shot Maybe I need Breakthrough right a break bleeding So basically there are drain or drain hole. I got a different shot straw I'm basically looking for the drain holes in the pinch weld Because no water gonna It's gonna come down And just straight away every hole I find Even where the clips go and you can they see kind of dark. No, you can see that I'm too far from you. So Do it it's like what like a little miss, huh? Oh, you just a little bit because that's the word the water will sit sometimes You know it smells like WD-40 sort of now, I'm just gonna spray the floor basically Avoiding like paint for now It comes on as a little you got thin mess, right? Yeah Now watch your eyes It's very similar WD-40 Is Okay, I'm gonna do the same on the other side Should probably go inside though Pinch well holes are gonna do the same over there spray each way And we got nine cans of this Come on get in there. It's kind of soft All right guys, we're gonna continue making the mess And we'll be back shortly all right guys my wand does not work not enough pressure for this to Give us the mist We're looking for which is a bomber these guys I guess for the purpose for my purpose They are like 40 50 bucks on Amazon. This came with my gun With fluid film that I bought a few years back You can see the attachment to the You know the air pressure gun Anyways and just using the straw does not give me the 360 degrees of mist Which we're looking for to spray The inside of everything basically so we're gonna have to wait on this. What's the plan? Go home Right, I'm gonna leave this here for a few hours till it's like late late come back get it home Let it dry for I think this needs 72 hours to fully cure the chassis saver This and I'm sorry all stuff Two hours. That's what it said. Yeah, not to whatever even if it's five hours. That's You know much shorter time than the 72 Meanwhile during those 72 hours, I'm gonna shop for something else for the mist that we need And yeah, we'll see you in a few days. It's gonna be a split second for you again And for me, it's gonna be a few days. See you later