 60-odd block cleaned up to reuse and it's all out so it's ready for us to get the stealing. It's not that bad is it? It's getting it up, it's gonna be hard. 30th of jute lie, just leaving Hodgson's now with a seven acros, six strong boys. Wet ass. Bit of a drop now, we're at 13 degrees, I'm gonna be short because we're working indoors and it's pouring down so luckily it's got this indoor job to do for the next couple of days. It's a double steels job, picked up two padstones but one's 900 long and one's 750 long so we can cut them up because they're gonna have 450 seating at one end to avoid having a vertical steel pulling. It's pouring down, it's 20 to 8 so we're on our way over to Liddy now. We've got an 8 before sheet to put on the drive for the skip to go on so we're trying to get there before the skip wagon just in case they come early. Yeah that's it, we'll check back in week when we get there. Here's our seven acros, six strong boys at the front there so I'm gonna start getting these in. I think we passed the skip wagon on the way so hopefully we'll be here soon. Right there's our steels. They were delivered yesterday by JN, not the other company we used, we'll be using them again. They're like here and that's where it's going. 350 nib off here and then the steel sits in 350 plus the 100 so it'll be 450 seating at this end and then can't remember the exact size opening. There are some marks there so so it's coming out to there so that's all coming out. Stealing up to the Joyce level there so going that course, that course there and then we pull this down and then start on the other side then. I don't think we'll be grinding that, I think we'll just drill it. I don't think grinding is just a bit too dusty. Get these strong boys in first and take it from there. And the presents off Alex. On your toy? Well, same toy as we used to have but I need a mint one. Upgrade. Did you get me the drill? And the extension lead? Oh yeah the extension lead. So the service hand drills come out because I don't like getting new stuff dirty. His old one was knackered so we needed a new one. The trigger wouldn't press properly. It's definitely this way out. The chuck was knackered as well. There's Alex's one, he used the air but the bow one. I know. I know. I'm not keen on that one because of the big switch when you pick it up. It's hard to pick up with that. It's skittish and that's slightly more powerful as well. They're just heavy and cumbersome but they're just a good all-round. They're cheap. They're less than they're strong. Yeah exactly. We're talking 350 quid for a box version that size. Where what bits do we want? Just the chippy. Oh anyway. We don't need the holes. The drill one so we can drill the holes in. Yeah. Just the longest one we've got. The longest one. These are the free stuff you get with it. This is 12. It's all the same size really I think. Yeah. It's got one in the van a bit longer. There might be one inside the other box as well. There's only the bit. There should be two long bits in there as well. I'll have a lock. Yeah. Where is anyway? Ready to go. So Alex's going to drill down. Works nice. It works up to this block here. We're just going to put three holes in each block so we can cut them off nice and neat. While he's doing that I'm going to cut out for these strong boys. I'm going to put three in. I've just got room between the joists to get them in. So let's get cracking. I like when you talk so I'll talk us through it. I'm humble too much. There's a cruise in the wall. Like and subscribe. So we've just chipped up the blocks and we've got the strong boys and that cruise in so now I guess not really much to say now it's ready to be knocked down. Yeah but we've measured the equal. We've put them in equal measurements haven't we? Oh yeah so we've measured them out and we've leveled and plumbed these this side as well. Yeah because we're not just holding back a wall now we're holding back the end of the house. This is the end. This is the gable end. So there's, let me tell you outside and show you. Or maybe not the doors there. But anyway that's the corner of the house there. This is the garage here. So that's the house. Yeah I've noticed inside they've used the insulated blocks. The two inches of polished iron stuck on the blocks. So we're hoping to save these blocks because we can't get all the blocks so we're going to see if we can clean these up. There's our pencil mark so we can start, we can mark that up now and start drilling that and start taking it down. Skip hasn't turned up yet. I thought I was behind the skip wagon this morning but we weren't. Anyway we'll just start piling this stuff here. Not out there anyway. And then same over there. I've showed you that before. This one's a lot more straightforward. We just need to tack three holes in each block because we're following that motor line there, that perp. And that's going to be plumb because it's the first block off the reveal. Yeah we'll start getting that dropped. Get this side done. I'm not sure we're going to put the stealing or not first. It depends. We usually put the stealing behind the accros but we're okay. We've got plenty of room to be in the stealing. We just might have to take it around into the kitchen before we put them accros up. As you can see those accros are lovely and plumb and lined up. Yeah so we've got them in every 9.50. Have you got any funny stories telling anyone? Um I've got plenty but I thought I was in the spot. We've got a nice story. Daisy's three weeks old today isn't it? Friday? I think so yeah. Alex's new niece and my new granddaughter. She's doing well. Well she had a bad night last night. The night before she stayed over at our house and she was a little angel. I'm thinking it's not Daisy that's the problem. Yeah it must be the parents. Yeah blame the parents. We're nearly there. We actually well I was following the pencil mark on the wall which is not recommended. We checked. So triple checked. Been inside, measured the wall, measured everything. So I've even measured put the measurement on the steel to work it out. So that means I'm putting the 300 padstone in there and it's a 200 seating on the steel. 350 padstone on that end, 450 seating with the steel. The reason it's got a pretty big seating is because that's just the brick pillar between the window and the door there. So originally we wanted a vertical steel putting down breaking into the floor and fitting in. So that's what that makes for. Yes these blocks are coming out nice. The seven newton concrete but they're quite soft. They cut where you want them. Drilling each one three times, stuffing them out and then they clean up as well. So the motor's that soft so we're going to be using. So that's going to get these last few holes I'm going to drill. With me new drill. Thank you Alex. Let's try that again with the cold button pressed. So Alex is going to drop the rest of these out. I'm going to hop up there and get that take that bit out in that corner ready for the padstone and the steel. And then you pretty much can get the steel in today. Get it in get it propped up get it bedded in and then we start on the next wall scratch. Instead of taking a big hole out and then putting the steels in we'll work our way in. Get these these accros dropped tomorrow morning then. A lot of people say why'd you drop the accros the same day? Well because I'm not usually here the next day so these can be left in overnight. Nice solid job especially with it being an external wall. So I'll crack on back to town that for a bit and then we'll come back some minute. Well in a few minutes. And this end this garage is nine inch wall. This is going to be picked up as well insulated but um it's a nine inch wall so our steel is actually going to sit against the outside. So we're going to have to put a bit of damp course up there just as a vapor barrier. Stop any water getting onto the end of the steel. And then this is the 350 padstone. 450 seating of the lintel so lintel steel. So that's that can go in after dinner. Once we've got these three these two courses out the way drop these clean them get them away and then we can slide the steel straight down there easy said and done. The second steel is going to have to go through out to the garden and into the kitchen on the side of this wall dropping on the floor and then we can get the accros in then from the inside. That's um that's like a cupboard under the stairs so that goes that way about 1200 that way 1400 so that's all coming out. But we're going to wait till we've got some of these block out we can just throw everything through into the garage then keep the dust down in the kitchen and yeah that's ready this is almost ready so um we're going to have a bit of it early dinner because there's a drink come so that's it after dinner tidy up stealing oh yeah what we're going to do is um what we usually do get it up into position back that far off the top and just spread a bed all the way across the top of it and then we have two accros left put an accro up here accro up here and then we actually tighten the accros up to the steel so the steel sits tight with the bed against those blocks which means you're not trying to point above after and you're compacting that bed really really tight as you go up so look i've got all these spare accros because that one that was a afterthought and that one there as you can see that seal enjoyed that block it's attached to is not being held by anything everything else has got an acro under it so that has been pulled by that and in turn the bracket is holding the block up so that's been a big help in that corner so yeah i'm going for dinner see you in a bit all right i'm just hand over got 60 ob block cleaned up to reuse and it's all out so it's ready for us to get the stealing trouble is we've got no sand and cement so i need to nip off and get that but we're going to get the steel slid in before i go and then there's a bit of architrave and stuff for alex to take off next door um so i'm going to leave with that it's only mogul which is the next town so i won't take long so let's get this stealing this big bruiser it's heavy this one heavy than normal right okay three two one it's not that bad is it it's getting it up it's going to be hard let's hit swap sides okay watch yourself take it further on so it's like it over hanging the edge it's just catching on the front edge that's it just pull it don't take the weight just let the just pull it that's it you ready yeah i'm going to pull it a bit more over it's going to drop in a second one two three pop up underneath it right put it over that side first put it on its legs on the wall again just whip the legs up onto the wall ready almost yeah it won't fall because the aquas are going to stop rolling otherwise it's going to slide in here are we doesn't matter they don't need to slide in as long as they're wedged one ready two three get by a bit that'll do for now we're going to get it the rest of the way up when we've got some sand and cement to put on top so as i said before i'm off to phoards in mogul down the road and i'm just going to stay and get this architrave in there you can always start knocking the walls as well you know yeah yeah are you sure that i'm not gonna do you see why is the house no it'll be all right um if you start on that wall just take this one here take the thing off the door for me first yeah and then just start on that wall good okay i should be back before then anyway so i'll leave you and alex's capable hands god help us right so like dad said while he's going to get the air sand cement i'm going to be here making a bit of a start in here because um as i've also been described it's going to be a steel going up there as well i'm going to pour them together so i'll start by getting this off and like work my way around a bit for all those to it i'm going to hope i want to knock anything i'll do anything wrong because i have no adult supervision of the or long one he's got a bit a bit well sorry um yeah okay yes please we'll get you on to time laps and make a start demolishing more and the the link's right and the name's right it's not kenny's this one no anyway um i think i'll leave it on normal speed so you can see what we're doing and i had a comment yesterday saying someone watched the video so let's put the steels in and we never filmed it so we'll make sure we get a juicy moment to this one so here we go it's after a lot of uh feeling about with these block thank goodness we had them we've got the the steel up so that's just a bit that's just doing more on the floor that's just uh trying to bed the steel up then we're going to get the give it a push get it up on to uh it's final resting place yep is it heavy is it it's a bit heavy it's not as heavy as it looks that looks pretty heavy well you've lifted it haven't you you know we've got it in our own we didn't need a lift yeah it's not ridiculous just lifting it 20 and lifting it above but put a certain height that's when you start stretching and it starts hurting but that's why we use the blocks took our time did it bit by bit did it the safe way it's 204 I hope it is 205 do you want to tell me about the viscreen up there as well if you pass me the camera I'll show them thank you so here's our bed all ready to go blushing thank you and we've got a piece of viscreen there that's a double piece of double 1200 gauge viscreen just to go between the steel and the outside skin because it's a 9-inch wall as I said before so time for the big push so what we need to do first is well put another two bricks in lift it break let it break and then we'll put the pushing another two bricks yeah we've got to slide it let's go this way so should I go over that side then um actually get the bar I take the very lift away so if you can push it the bar is it better at the top it's less gap pushing it out though too okay pushing it out that's okay you just push it back in with the shoulder want me to do that in it's all right one second you need to guide it you probably need to push it out a bit but let's get it in position first right so you're just steady on that but it's on the block work okay it's in so time lapse the rest okay okay a bit of a bomb size at the moment that actually just tied in now a bit of bobble left steels in place these are that one's coming out that one's coming out now because the steel's up and it's propped over yeah the bed's nice and tight just needs that a little bit bit pointing up where the acro was and probably look that one there but yeah solid we just need to get these two um pads on them now which I've just cut that one's 290 that one's 340 um there it is 340 so we'll get them in pack them up and let them go off overnight and then we'll try and sort this issue out next door we're gonna um customers got an idea what we're gonna do so we'll find that out later or tomorrow morning so for now I'll just put on time that's where we get these padstones in and then do a final wrap up before we go I'll just get just getting all the tidying up and so we'll get these two in and then we do have a little wrap it up before we go home so if you're liking the video so far give us a thumbs up we get like we had like 21 000 views on one of the other videos and probably about I don't believe in it a thousand likes so if everyone gives views it just stick the like button while you're watching it unless you don't like it of course but it costs you nothing does it does the channel a favor I don't know how it does the channel a favor that's what everyone else says so I'm assuming it does so um give us a like and subscribe during the other 16 000 who've joined us and then hit that notification bell so you'd be told when the videos are coming out to come out Friday anyway but just in case we sneak one out I'll stop waffling yeah get back to you later I hope you're wrong that was supposed to be time that's where I forgot to press record so there you go pad worn in I've got the echoes up overnight well that was off I never used to put a bed on top of between steel and the padstone but I got a lot of comments about that so we've got room here with this we've got a nice bed and then a bed above nice so I'll time-lapse this one a bit closer up this is our long end so here we go and there we go part five 10 plus five skin done stealing so we've got a 290 pad 200 seating minimum 200 it's nice the side bed at the top currently being held at these two accros and the water goes off and a 340 pad padstone at the end I didn't take the padstone right through because that block there this one here bonds through so if we cut that off then you have this block no sorry this this block and the padstone that'll be in bonds into this corner so that but that block is giving the corner strength so that got the pad and then pointed it tight underneath that lintel as well as steel which is on his handlapse so then accros can come out tomorrow and we can head the next door and start getting this side done that side we'll have to put the steel in first so it's through the garage into the garden and back along here I can say there is this wall to come out but we need to sort that out tomorrow that's it that's our speed pump for this job so um yeah we're going home friday so well as dad said while I'm all these off doing the air getting the sentiment this is probably an outtake because I've just had a brain fart