 Hey everyone, Shaber1000 here. Today we're going to make up some new cables and get these old nasty ends off of the golf cart. Cables themselves not bad but they ain't great but we're going to try to make some up. I'm going to solder these in here if I've got enough solder. If not then I'll have to start crimping them. If it comes to that I'll show you how I crimp these without a crimping tool and then we're going to put our sleeves shrink sleeves on them. So first I got all my stuff out here I got to measure each one like I know where this one goes so that way that I've got enough cable to go from one to the other so let's go ahead and get started on this. Okay guys so what I'm gonna try to do is I'm gonna try to heat this up and I'm gonna try to put a little bit of solder down in there then we'll stick this in add some more solder if we need to so let's go ahead torch is gonna be a little loud sorry for that so I'm in there I'm getting very low on proofing might run out of that first too. These battery terminal ends they are tinned already so and that looks pretty good so now we're gonna do well let that cool down a minute because I don't want this stuff starting to shrink before I get it all the way on there so we're gonna give it a second and then I'll kick you back on. Okay so let's see if I can just push it on this way yes I can I'm gonna bring this up I can probably cut this in half and use it twice I think that's what I'm gonna do make sure I got oh yeah I can do that all right there just enough to cover that up as you've seen the original ones don't have that because there's nothing on top of here that's metal that can short these out but I still like to put them on there make it a little more presentable than if you want you can wire brush them off and make them look nice so what I'm gonna do I'm just gonna use my lighter for this because my heat gun is still packed away you can use your torch if you're real careful I'll show you how to do that you just like that we're looking at just like that now let's go to the other end what I'm gonna do is just kind of measure up a little bit it's gonna be in about that far so I kind of just pushed real hard on this and it made a mark onto my rubber piece right there make sure you got enough enough cable before you cut the ends off now I cut these ends off because I already checked it and made sure I had enough cable because if you're running along cable you may have to take this piece bend them out and bend them out which you can see it's kind of a pain to do that so we're just gonna like I said I'm just gonna show you how to do one I don't know if I'm gonna get them all done today I have another video I've got to get started on and like I said these cables aren't the greatest but they'll work if we ever have to get new batteries then as I replace the batteries I will put new cables on as I go but for now you know I just don't we just don't have a thousand dollars to put a set of batteries on an old golf cart that is actually just for fun you know make sure that fits in there we're gonna want it like that so it does now this we got to put on first well no we don't it'll go over top of it never mind if if you're if your shrink wrap won't go over top of these then you'll have to put this on way up here so don't get hot and shrink around but since this goes over top of this I don't have to worry about that I just gotta make sure like you don't want like I don't want to put it on like that because of this end so you want both ends the same way unless you have to you know you might be in a position where this one has to be up higher but normally it's going to be like that so I'm gonna do one more and then you know save you the because like I said it's it's really repetitive why that changed okay it's really repetitive and I'm probably gonna have to put a piece of metal down here I'm just if I got a piece of metal okay I don't have a piece of metal handy so I'm just gonna go ahead and do this I mean this might help it yeah that'll help this is what I used to cut the wires with a good pair of these will work these lineman pliers good pair of those work just these are I got a shorter pair and a longer pair these work pretty good so let's go ahead let's do number two all right well you know what you can also do if you do have a cramp or you can solder and cramp them which would be fine so I'm gonna I'm gonna put a little bit more on this one let it cool I'll put my heat oh yeah that's much better and I'll put my heat shrink on there a little bit too much on that one but that's okay yes very nice so let's let it cool I'll put the heat shrink on and then I'm just gonna start making all the other ones I got two on the cart that I have to make which I'm not sure if I'm gonna I may just take them off and do it up here so that way I don't have heat around the golf cart stick around and since this cools we'll put this other heat shrink tube on and then that'll be one so close the garage door because monkeys got something in the washing machine so before I started the video I was getting everything set up for you guys and she come out and holler at me and says she needed help her mom was feeling like she was going to pass out didn't feel real good and nauseous so we had to call an ambulance on her and so she's heading back out of the hospital monkeys waiting a few minutes because you know they got it by the time they get her in and get her checked and everything so she had a doctor's appointment today which the doctor comes to the house the doctor was supposed to come in today and she decided well she wanted to go early I guess so so hopefully she'll be alright so keep your fingers crossed for her and thoughts and prayers and all that appreciate it so but yeah hopefully things will be alright for for her we're no stranger to that I mean they've been called here many times she always comes through so she was joking with the paramedics she was flirting with them as she always does so hopefully she'll be alright she may just be dehydrated we have trouble getting her to drink water you know you can't like you can lead a horse to water but you can't make them drink kind of same thing here you can't make someone do something they don't want to do but monkey tries really hard you know drink the water so it could be dehydration we're not sure but I'll let you I'll keep you updated on how she's doing so anyway thanks back to the video okay so monkeys just now leaving so let's go ahead and put this on here real this end on here real quick just slide it up on there right there that's her starting car so fire this up to really fast remember be careful or it'll just melt off of there we've got 14 more to go not actually I've got 12 more to go and there's two ends on there I can use on that new cable so what I'm gonna do is I'm gonna take the new cable and I'm gonna measure out and I think I can get about three out of that if I can get four that would even be better so let me get that cable off of there and get it over here and I'll measure up and see if I got enough for three to four I should have at least three it's pretty long cable that'd be great if I could have four okay we're gonna put this on and then I'll go ahead and make up the other ones I might have enough to do all of them which would be great yeah that would be super cool if I could do all of them because I've got two more cut here that's three this is four because I'm gonna leave this end on here and then I've still got all this so I'm pretty sure I might be able to make all of them so I may have made that one for nothing but that's okay I mean I'll still use it on it but torch on here I'm gonna leave this on because whether it's positive or negative like on a boat or a golf cart you know you don't go to the frame like you do a car because of all the fiberglass and all that stuff now so like when I hook the stereo up and stuff like that I will run you know two wires all the way back to the battery one will be for a negative one will be for positive so that'll come in handy I'm gonna leave this end on here this is lead but it'll be alright I'll leave this end on here I may have to put a washer on that one but that's okay I'll clean it up and it should be alright so I'm gonna go ahead and keep going on on this one this one will be number three so alright guys stick around okay guys so I'm gonna show you how I want to run run one of these and then you'll get the idea on the next ones I'm gonna use washers whenever I can I don't have enough flat washers I do have some I do have some lock washers but I dropped my bolt bin all over the floor so they're all up underneath the refrigerator in the in the garage so and I've got some new bolts here some of them are stainless some of them are not and some of them are a couple different sizes well half inch and nine sixteenths but that's okay so that's what I'm gonna do to the rest of them and I'll back you up I'll do one more let's see can you guys see that yeah alright so take this one off let me get a couple washers now I'm just gonna I think this one I made longer on purpose shorter one on here like that then I'll hook the positive and negative up last okay so I got a wire brush here I got a couple that need to be cleaned off real good I'm gonna take these down I'm trying to keep them away from this see this one touches that so every time I take this cap off to check it I'm gonna have to I might be able to let's I don't think it'll run underneath see this sheet the all every one of these batteries used to have straps on them we couldn't figure out why now I know why because when you take these off the straps are getting away so that's probably why he took the straps off monkey still trying to figure that out it doesn't really matter but now she now she can know this on here I don't know if that'll I don't like that that would work but I don't like it like that so all right it just it is what it is they're all full and one on the other end of there's the same way it'll be the same exact way okay there that'll work just got to flip this yeah that'll work hopefully this will take care of our battery issues for a while now tighten these ones up this is an old wrench I got in a bunch of free tools I just keep it in here for this reason straighten this one out a little bit I don't like that bend in that and it would be that I try to keep big cables like this as short as possible last resistance special when you're running 48 volts all right now I got to do that a few more times about 12 more times be exact so let's say two four six eight ten 12 yeah all right I'll be back with you guys I'll show you when it's done okay guys this is what I came up with I had enough for to put all brand new cable on here so that's good I still have an extra one I threw up in there just in case threw up I got to fix this and then I've got to get this mounted back up but yeah it's almost full charge but yeah I had enough so it's got all brand new cables now these mains that one there and that one there I double-knotted so they don't come loose so I'm getting ready to try it out here when I'm plug it and let's see if it moves I did shorten this this up for my pop box like I said I've got a lot of wiring clean up to do but that's just zip tying and stuff like that so all right guys let's see if it'll move working everything seems to be fine batteries are charged still every once in a while you hit that gas doesn't doesn't want to go for it'll go backwards so I'm gonna I hear the brakes squealing so I'm gonna check the brakes make sure they're not dragging if they're dragging that can cause that because doesn't do it in reverse so all right guys there you go I mean I'll just keep a look and see what the problem is that old pop box was definitely bad but we'll see I won't bring you in for the cleanup of the wiring all I'm gonna do with that is just zip tie everything up make it look nice and neat the charger since it's not gonna bolt or hooked up down to bottom anymore I'm gonna run something from that frame over to this frame then I can put my solenoid up there where it's easier to get to instead of that's where it originally bolted on a little hard to get to it's not screwed in it's bolted in so as you can see how far down them holes are yeah kind of hard to get to and then this will just bolt up here so but yeah it's finally looks nice I got to blow it off and everything I still got to put my tie down or my holder down my battery holders in so I got to do these might bring it along for these put these in since that's kind of part of this then once I get all these wires up here zip tied I zip tied these ones myself because they were all they were all messed up so I zip tied these these are headlight wires here and turn signals so yeah that's pretty good zip tie them up and then I can put the hood back on or the nose clip I got to fix this better fix that that's been broke for a long time the hood's over there so alright guys thanks for watching I appreciate it she barely met the man alleged I'm gone for now we'll see you guys in the next one bye bye and take care