 Look, you got these nice vents and I hope I've not marked it already. You got these nice vents and When I look on the bottom of this one We got these nice vents, but then you got to use silly stickers And these vents you need these vents to be kept clear because it does get really warm in there sometimes Especially on a warm day flying around and you've got more than a couple of batteries but look The third of me ventilation is covered up and I stick me finger in the butt of it to Check for heat and sometimes it can get really warm in there Like I said, you know a couple of couple of batteries on a warm day And I wonder if you know just having that bit of extra ventilation could help So I'm certainly not gonna put stickers Across here at all I've stuck some I put this back together and I put some of this nice I've got the white stuff last time and it's pretty good. I'm quite impressed with it But this stuff's clear. It's an extra 50p, but it's clear I'm gonna see what this is like But I've put some across the top of there. You can hardly see it. Can you? Which is great. So and then I thought what I could do is I could just set that in get it Sort of glued and then it'll be ready for tomorrow for me to build it up again But of course, I've got to wait for that because that takes quite a while to go off So I found something Loving that we're here now. I've put the I put the ball back in for the camera and It was just proving to be a little bit of a pickle Trying to figure out exactly How to put the antenna in and the reason why I say that is because even with that See what a planar antenna the square antenna that I've got It doesn't matter how close I am if this is turned a certain way I lose signal. It doesn't matter what channel I put it on. I lose signal I'm sure I've mentioned this I've in a video that I have put up or haven't put up I'm gonna actually for close range I'm gonna put the internal antenna that came with it back in and see if that fairs any better But the little antenna Transmitter antenna it did come round And it came over down this leg here and the white seems excessively long But it came down this and this one this leg here or this and Because I can't quite work out where to put it and because it doesn't work as well as what I would hope You know like I say when it turns I've just stuck it down the front here Now chances are I'll have to go into this again at some stage. Anyway, I would swap back out or Yeah, it's a black But there's something as well here is there are on two of these Motors and if I remember rightly my position is here on two of these motors It has these washes Now they're pretty rusty washes and I've looked at I've been looking for a spare set screws not that I need them at all the screws It's just I wonder if they had these washes in there and they don't have them in the spare sets of the screws or fixings for this And I'm wondering why there is actually just two or two and they're on the opposite legs as well There's another another washer there and The wash is down here for this and that goes there Not opposite each other on the same side But on the two opposites nothing as you can see there's there's not been any sort of washes here on this one And also that's the same for this side no washes I'm just wondering why why they're there. Is there a slight imbalance in the actual shell and They found that putting the washes there would help with vibration or something These vibration if it's slightly off I Don't know Honestly don't know but I tell you this Because I did notice that when I used to put this on top of this desk. It did have a slight wobble Not on one side, but on the other side It was like there was a millimeter or something gap where there was a slight bit of movement so you could tilt it Just an observation the worth noting that Putting this back together of course I'm gonna have to put The washes back onto the same places. I have asked about this at Hudson But sometimes it can take quite a few days to get a reply. I'm sure they're very busy there dealing with all sorts of things But I'm gonna put them back in Just because they were there anyway, I just thought that was not worthy Setting in the camera. I've screwed this down, so I'm not gonna take a lot of party And I just want to get it back together. They're getting out early get up a bench I've got other things I want to be able to do. I keep getting notification about this This I'd power supply that I bought that I bought DPS 50 15 about You know if I've got any problems with it I've got to notify them really quickly because they're the warranty I'll run it out. How long have I had it not very long a Couple of few weeks, but the warranties about to run out on it so that's Was I've keep checking this camera as well to make sure that's working So I need to do some stuff with that. I did ask actually the RD tech whatever it's called If it would be okay using inductive Loads like my solid state tells the coil, but he hasn't got back to me That's all with that. I don't know I'm gonna respond because I've asked him to take off the adverts of my Of my videos because I've put adverts on a few of my videos. I'm not really happy with that Don't get me wrong, you know, it's it's okay. I put link in the description, but I don't Advert to my videos so I digress I'm gonna put these back in I'm gonna leave that little antenna down just down the front there sort of sort of loose I don't think it's gonna matter too much. I mean here I'm trying to fit it in down back down here again. It's a bit of a pain in the butt to be fair I'm sure we'll just see how that goes. I can always take it out and just take this off and move it out again It's not such a big problem It's a whole bunch of screws. Yeah, and earlier on my I looked at these which I thought wow There's quite a lot. So I bagged them In order to work out what to put where again I decided because I didn't know About putting the board down which exact screws they were I went through process all of the nation I know they're for the motors. I know they're for the main show And there's little ones there for the top pieces GPS and compass and these other thin ones are Actually forgot what they are, but these are the ones here for the board. So as I get through I might be running out of screws And then when there's holes, I'll just put in what's left Oh, I know where those thin ones are for there for the elite, you know for the feet Not not here for the feet Underneath You know there We get around to that a little bit I wonder if I should carry on filming this putting it back together again, because it is taking a bit more time It's a lot easier to take it apart because it's just Get everything nice is a bit more time-consuming. I can't really see He's going to be really that interested in watching that There's me tweezers Flatten look like pointy bits Excuse me for Digging into my fingers obviously a bit unsafe with tweezers That should just Snugly fit in there nicely. I'm hoping That's it. Yeah, beautiful. That'll do. It's quite a nice little snug fit Gotta get it right. Gotta have it twice So that's why it's nice and snug everything out of the way. Of course I've still got the LEDs to put through Probably will have to pull these out again. So I don't even want bothering to put those in I should probably be just getting these clamped down and And then just working from there. So I'm gonna do that. This is got two screws in it Yeah, I'm here not at the back of just yet just in case I were to take it apart So I wasn't quite sure what this goes from What is quite sure And this has got one two I've got a whole bunch of connections there. This one's only got four. Oh, here we go It probably goes over here That's good Cam is still working. Yep It's gonna get warmed up a bit first and it seems to be once it gets too warm It was all happening a lot quicker when it was 60 frames a second. But I just leave on 30 frames now It doesn't seem to be any movement either on it where these pressed down it doesn't seem to be a clink clink clink clink type There was with the black case That's pretty firm in each corner. I can't tap down and there'd be any movement No No, I was the the base and where there's put the Then the 5.8 gig transmitter aerial antenna. That's where it was supposed to go There's little Grooves Grooves that you can put away Through space quite nicely That's good. It's all in the right place There's two grooves one side LED lights down and the other side you can fit where it's all the space for it This is here where I should try to fit it. I'm pretty sure that just sits in here Fiddling just slides in that's slid in but I think I don't know There's all that lots of gunk so you can't be touching anything but that is slid into that space now It's not gonna be Where the body should be coming together Hopefully that won't Block anything I'll be in the way Alright, so that's outside That's side USB's in Just these two Right, we're in there. It's good to go. So I'm gonna put the top together now There's a glass bit, there's a canopy even and of course there's the wider parts at the bottom So that's pretty self-evident That's gonna get a guy Self-evident I'm trying to put it in from the wrong way around Top bit that just clips into place nice Well, it's definitely in place. It's just not made any real clippy noises, but that's That's the top bit. I don't think we need any sort of gun called gum on there But then I saw quite a lot of videos they all had white ones and I really like to look at the black one So, GPS Let's do the compass first Of course, it's nice and easy. Two screws And it just goes there. Now, I Try doing this without putting the compass in screwed into place correctly When I first took this thing apart And it doesn't want to start up. It doesn't it it won't fly unless you put it in the right way around So there's a little something that's not working So it wants to go this way as well So the screws go in like that And it sits just underneath the canopy Like this rather than Like that Yep First one in place But yeah, it's quite it's quite sensitive To how it wants to be that camera's still working. Yep Surprise There's a thing that I don't want to be Magnetized at all I'm going to assume that's going to be great Get in the hole It's level, it sits firm Now that's something I've noticed about this compass this time I'm sure I've already said this but I could have said it in a bit in the film that I lost It was a screw driver, it doesn't fit under the tiny screws, does it? Yeah, it takes a lot longer now To calibrate the compass It used to be two turns clockwise And then two turns anti-clockwise But now it's more like four or five turns clockwise That doesn't seem to be Fitting in as well I hope it's maybe it's just down to me not applying enough pressure It's because I was pushing on the shadow a little bit and I was trying to be dead careful about Pushing on the shadow but that's certainly That's certainly a bit to there And now we've just got this This side is the part that faces upwards And if I remember correctly this bit goes out the back It doesn't fit nicely into place like the main board does Where you've got a couple of holes to align it up with But never mind I'll get one of these on each corner Opposite corners And then it's got the It's got a lot of lining To go, because that way To go between this It's gonna go whichever way this wire goes through I actually cut this in here to make it easier to get onto here Otherwise it was, this sits down I push this up nice and firm into the top Rather than have it the way it was Because it's supposed to be a screen between those two things I get around it and it's far away from the rest of it as possible But very sensitive to GPS on the point of You put your hand over and this is normal as well I've asked them at Hobson If you just put your hand over the top you'll lose all GPS And if it turns over If it, you know If it spins over you'll lose GPS as well But I don't use GPS so much now I mean I don't use the GPS so I might take it up I might take it up first of all And just let it hover there for a second I wonder if there's people about to show off a little bit Let the GPS hold it up and then just walk away from it Without even looking at it Showing off like Come here little monkey It's probably the 50s bit It's trying to get these pretty screws in Because they're not magnetic Or they don't seem to be They won't be picked up on my screwdriver Ah Damn Light down on my lens So I can see See if I have this force fade off Okay Right So that's the front And so then why is it going to come down in This side So I want to put my This in here Like this And those wires through Push all this up nice and snug Into the top of this I'm hoping that The interference Is going to stay to this area Let it get on and do it's job Across the road for me where there's a A field Unfortunately there's a Transmission validity mask And I figure I used to Ah Just to go and see a friend up there And her place was right by the Transmission mask that I actually Figured it was there I don't know if that had been caused me to Cue little issues so That's that I'm just going to connect these Into these Pop that on there Put the thinner screws through the base Of this into this And then lock these screws into there And we are pretty much Put together But I really need to go Oh and I'm going to hot glue that I've had the The heater on the hot glue now So that should be nice and warmed up On the The gun I should say Hot glue gun so I'm just going to Push that Because we're going to make sure that there's The battery can get in and out So just going to be a take I'm going to Go and find a battery to put in it And make sure that's out the way So I've got a battery I've got my cup of tea We'll leave myself It's good so far The aerial doesn't actually get in the way I've got that in the Right sore place which is good Just going to plug that out again I'm just going to chuck a bit of hot glue down I'm pretty sure it's going to be okay where it is But I'm just going to chuck a little bit down there To just ensure I just move that wire up Away there So I can get the nozzle of my glue gun in I'll show you Turn the bloody thing up when I do that So there's just a little tiny gap down there I'm just going to chuck a little bit of glue Just in there Just so it You know it just doesn't vibrate How it's at any stage So it becomes a problem Putting the battery in and out I'm not sure if you can actually see that I'm really sorry if you can't So I'm going a slightly different angle Because I'm governed by Having to put in the USB cable to charge it At the same time I didn't realise The camera had gone off I just checked it to make sure it was still working It was all Never mind It's all in nice On the black one On the black one It was almost like it was just slightly off So you'd have a bit of movement But at least it was in time The mate has looked like it nicely Look at those Beautiful Okay Well I'm going to put the back door on Even though I've got a white one coming But I'm going to put the back door on anyway Because I was going to think about it Because the batteries are so small What am I going to do with that battery? I'll put them underneath there Right in front of my eyes Because the batteries are so small It's not going to fall out Especially the way I fly I could quite happily fly it like that So I'm just You know Just gentle and smooth And quicker I'd say twice as quick Maybe three times quicker than the GPS But not Full Blastic mode I've had a succession of motorbikes In my time Most of them Well, the last three Were Kawasaki Ninjas 750s Absolutely love the 750s Just got Well Plenty of power Absolutely plenty of power But the one thing I look at is You don't Just because you've got all that With mine With this stage Three tuning and everything It was like a 175 mile hour job But it doesn't mean to say You've got to open that up Everywhere you go You can just gently have it And have nice power And smooth That's the way I look at these Especially since A couple of crashes So I think I might just power it Without Oh, I've got no charge, actually I've got seven volts on those batteries Oh, nice And it's showing up red now On the battery indicator On the handset And in total then That gave me 10.5 flights On a single charge From 4 power, 8.4 Down to 7 volts 10.5 cycles Yeah, that's good That's good Okay, there you are That's good There we go There we go There we go There we go Right, I'm going to drink My cup of tea now And I'm going to say goodbye Fine, I'm going to drink My cup of tea And Come back when I have A little biscuit That's all I'm going to say Lied, I misspoke I'm too excited I drunk half of my tea I've not had a biscuit yet But I'm going to chuck on a I'm going to chuck on the props That I've been using While it was black As you can see Not really damaged I was out of the maintenance field And The printer spares Got all those black ones as well And I took it really quickly Into a turn Going really fast forward In altitude hold mode Because this thing Don't have a shipment It wants to be more When you can make it I think it snapped a prop I think it snapped a prop It's got to be an A then All right Let me just get Well, before I Power up that transmitter Not so bothered about that Not so bothered about putting that on So much We don't want to run it without This on Because I'm not sure But if there's anything to do With like CB radios If you don't have your A real on So it's tuned You can have very nasty VSWR ratio Or VSWR ratio With a voltage standing wave ratio And that's not healthy For Your transmitter I am literally going to start This poppy up here First of all we're going to I hope you can see that So we're in the red on the battery On there So I just tilt that up a little bit We're in the red on the battery That would be alright Because it's got 7 volts And as long as those batteries Don't go below 6.8 Type thing for my comfort So of course we want The all important video To kick in Please don't go Pop Watch Bang That's a good sign That's a good sign And we've got the video The all important video GyroSense is happy It's calling for me to calibrate Compass 1 This might take a bit of a time Because it's been being like that So this is going to be Normally done by now With the old control board That I had Still asking me to calibrate Compass 1 Still asking me to calibrate Now Compass 2 As you can see The light's changed as well This one's going to be done Quick air About 2 on this one That'll be done As it used to be This is half way into the second one That's the second turn Half way into the third Third turn Third turn we're done Okay Let's go to the next part Is the magnet We've got no power On the battery at all On both items I've got 6 GPS On the handset Nothing on the quad That's alright I can tell it to start up Without needing GPS Because this is the new board So I'm just going to tell it to fly When there's no GPS Ready to start it I don't intend on taking it off It's not going to go anywhere I'm just going to get it to go It's in altitude hold mode anyway I've got nothing that's going to Go nuts have I You can see that Beautiful Beautiful beautiful beautiful That's just the test So we're all good We're all good I'm going to charge that up I'm going to stick myself some batteries on charge And Have I got too charged? I have I was charging to the other day I forgot about those So actually all I can do Is I can do a quick blast charge With my SkyRC Into these That gives me about an hour To get something to eat And then I can Rush off down to the fields See how quick I can use my quad Yeah, joking Just give it a natural burst While I put those on charge I'm going to stick another couple In power on charge on that thing And have four batteries Doesn't seem to be particularly windy out there at all So that's it guys That seems to be the mission complete I haven't put the back door on yet But I may I may not Probably will But it works It works, everything calibrates in Everything doesn't space to It starts because it's space to And that's all that's left to say Everything's as it should be So there you go That's the shell swap out Hope you enjoyed the video Hope you enjoyed it as much as I Enjoyed actually making it It's been quite good It's just nice that it worked Little droney And he's got a brand new suit Brilliant Till next time Take it easy And I shall see you soon Thanks for watching