 No one's here So I would bet possibly this one here is it Wastram Yeah I've seen these before Cracker tucky uses these things fall out and fall down in the bottom Well It's turned off so I'm assuming But this is probably the reason why it's probably got some problems True see what's going on Video camera decided to record in elapsed mode. We went ahead and cleaned up this fan blade It was pretty nasty looking We're gonna get this thing set up in there. The shaft is just a little bit longer on this one here But we can trim that down not a big deal. We've already checked for leaks down here did not find anything Same thing over here. Nothing was found could be just because the evaporator fans not running We're just gonna get this replaced. Like I said, it's not running. It's jammed up. It just looks like crud It's what we're in the process of doing is replacing it I went ahead and plugged it in and seen which direction it went And it seems to be going the correct direction to blow it out Of the coil box and set it down below it. We'll have to reuse these fancy connectors They're nice and waterproof If you wanted to switch the direction around you just literally pop that thing apart Like that right there switch it around It's just basic bushings for bearings, which is anything but fancy Looks like I should clear that from shortening to it, which works out good But it's gonna get us off a pickle here and that's that's what matters because we don't want any relish now you can see that that's Above the front of that you want it to be behind it. You don't want to be On front of my hit now if we take this and put it up against it You can see that it clears it not by a lot, but it does clear it I think I'm gonna go ahead and trim off this little a bitty piece there just in case That'll make it easier that little device there. It's not every day you use it But there's several times where it comes in handy Right now that should fit in there a little bit better. Let's press that thing back on there and ends up Pressing on all corners including the center and that way you ain't gonna break it But we got plenty of clearance now plenty of clearance We'll clean that up there too. It's got a little bit of mold bucking stuff on it and that looks a little bit better There we go Just need to adapt this power wires here I've got females but that nice rubber there is a lot nicer than the rubber actually not even rubber. It's plastic That is on the ones that I've got so we'll just go ahead and trim these up a touch and Put a buck connector on it a little extra precaution here. We'll go ahead and run some tape around it Keep some out of the fan blades and Makes a little less noticeable Use the good 3m Scotch tape Super 33 plus they crammed that damn TSV head right in there Don't leave you do that extra freaking room here at all. There's one of the longer ones Accidentally This must be it Now it's in there It rotates Let's plug this thing back in and see if it's got motor operation now Unfortunately, we lost the beginning what we found was the system was low on refrigerant Or at least it looked like it was the cyclist was half full almost completely Down to the bottom quarter This thing wasn't rolling It's running crazy fast now They don't like that. We'll have to order another one, but at least this will get them going. All right good See if this thing's pumping yet Yep, it's a pumpkin and if you look at The sight glass there it still looks low. We've already scanned for leaks Didn't find anything It's got TXV, which we already seen on the inside Condenser coils got a little not too bad. You could get a little coating on it. We'll brush that off try to get that with this Metal brush, which I usually don't use Since it looks like cat hair, but I'm sure it's not got into that tight spot really well As well as check the high side while we're at it since we're Gonna be charging this basically off the sight glass which generally you can't do on little systems So they don't usually have a receiver like this very unusual. You can tell it's a better built unit Even if it is got a small leak somewhere that we didn't find Yes, I know I'm using the pliers backwards You can do that with these pliers Made the mistake before in the past and not checking high inside when I added to a system and Just charge till full sight glass and it's bit me in the butt to where I didn't realize that hit pressure It's got a rocking in high the coil. It's like it was clean and it wasn't. If I've got time to do it I prefer to do it that way. I Don't think it's so low that We needed to shut it off and then turn it on that way that you know Suck anything in especially run it for for good lead it fairly decent size leak Precious about a hundred and five degrees We're getting there Seeing the little bit of flutter in there. So there's right at one pound We'll let it run for a bit and then we'll end up Add just a little bit more A lot of maybe about three ounces two ounces more Don't want to get too crazy at pressure holy crap We are running a hundred and twenty degree evaporator It ain't that warm in here not granted. It's coming down. It was getting a little bit of you know saturated liquid when we were charging it That's a coils guy. It's pumping some heat May have forced it in a little too quick, but Let her stabilize it starts come down in temperature. The pressure will come down too right now. It's a you know full Warm box, you know, it's sixty some degrees. I think yeah, we're sixty one degrees right now Right on 28 evaporator see that makes it a little easier to see that's a little easier It's coming down It's coming down. Let this run for a little bit may have to re scan it Maybe hit it with the h10 and see if it finds it things are looking a lot better now And I saw the side glass everything's good to go Like I said, just got to scan this thing over real quick one more time It's a bit too tiny ones, you know, this was worked on I don't know what E&R means But back in 16 five years ago something was done All right, we're bringing it back out of retirement We're at 35 degrees already, so they must got that working. Okay, let's go ahead and shut this thing down One of the problems with that is Things running you're at your lowest pressure possible for that evaporator And so you're not going to get near the leakage But I mean even disconnecting the hoses making sure I didn't bleed anything out when I did it I Can still tell it's speeded up a couple times just because it knows it and that's Something that only an analogue detector We picked something up like that You heard it just change right there now. I could be because of the temperature difference Go ahead and pull these back out. All right, let's make sure she's tuned in That's about where you want it at you want to hit about on the okay mark. I'm a little hot It's a pretty decent sensor It's maybe a year and a half old something like that two years I haven't been using this thing much because I've been using the DTEC select stratus DTEC stratus most of the time Now the one thing I know about this detector There's any leak in here this thing would have gotten it And they would have went berserker Which makes me feel better because My stratus or actually I was using the DTEC 3 Today just because it was easier to reach than it was to get to the other one. It was on the shelf behind a bunch of stuff And I'm not getting anything Nothing up in this area. I mean if it's if I got to be right on it with this detector it's I'm not too worried about the evaporator and that's generally where it leaks at And I don't you know, I can tell you they likely do not Keep any vegetables in this area. This is gonna be more meats And generally that doesn't leak as often. Let's scan the condenser Cyclast nothing on the backside Takes a little bit higher tech rate Not there's where I like it at Usually down in here is where you're gonna get your leaks at Get all up in that area here We got bellows at leak Yeah, anything that we got Physically do it this crazy. It's uh something that might have been happening for a long long time I would say if it's leaking anywhere it'd be down in this coil where they've got the Hot gas lines. That's kind of reluctant to stick the probe in there too much or some oil looking stuff down in here That could be out of that motor, but That sure looks like oil right here It could be just water it was because there was water in it earlier. Maybe it evaporated It sure kind of looks like oil. Well, I am pretty convinced that if it is a leak, which obviously it must be Somewhere it's not gonna leak out in a week or two or a month or two even it's gonna be a while But like I said, this is a really nice unit Don't see a bunch of them. I think they're definitely probably more high end You can tell this customer really likes good equipment. He's got south bend ovens He's got hijasaki cooler over there hijasaki ice machine He's got some good stuff But this one here, like I said, we did what we did everything's working good I'm gonna leave him a copy of what I did and the motor itself so he can see it We've got down there to temperature, which I think Let's see what our set temperature is here set 34 So it's set for 34 degrees hard to know how all these stupid things work too many dang different controls But like I said guys if you enjoyed the video and you want to see more like it Give it a thumbs up check us out on instagram and facebook and let's go ahead and get on to the next call