 Got some fiberglass in there Did a pretty good job Not perfect got some resin all over myself Came up pretty good though. Yeah Obviously need to trim this off and clean up this edge There's the basic rough shape there. I hope it's not curving too much that way I think that'll be alright The only reason it needs to be fairly straight all the way down is that the back The propeller has to be in the water so it can't be, you know, the boat can't be too high But I can always make the shaft of the propeller straight down So I can make it straight down I've got to be careful. I've got to be careful I've got to be careful I've got to be careful I've got to be careful But I can always make the shaft as long as it needs to be I don't want to tip this end down anymore because I want this, you know to line up right with the original thing so it has a smooth ride for the water all the way through Let's see. It's lining up well on the inside. I get something just pushing Against the edge a little bit. I can line it up. This doesn't quite touch the bottom I think if I take take out a few of these PVC things and let the back spread open a little bit Then it'll be able to sink in a little more Just to get this to be right even with the mold Could also be some dirt in there. I don't know. I didn't check before I put this in Anyway, it's close enough that yeah If I take out those PVC things let the mold spread a little bit. This will definitely touch and then maybe put a few Poles or something in here just Pressing it against. Yeah, that lines up really well. Yeah There is another thing that I can do to like straighten this out a little bit which is Squeeze the sides in a little more When you squeeze the sides in on this kind of shape the ends come down That would also make it faster so I'll just squeeze it in as much as I can and still be able to Fit the pedals and my butt in there. I'm not gonna do the other half of the mold today though. I want to Think about what I want to do with the other end there This is not bad. I Do want to be able to attach your order. It looks like this line right here Is where the material meets I could Trim it right along there, then I'd have a flat Spot to put a hinge in the rudder. I might be able to come up with a Even better thing for the other end though. Oh And a few people asked how I got this mold. It's from the shark slicer and If you go to construction boat like one or two or three or something you'll see me making this Try to remember to put a link in the description of this basically It's two flat sheets like this was a flat sheet and the other side was a flat sheet and I connected one end like Connected this part all the way here and then stuffed Pieces in that were the cross section I wanted and then I put some more fiberglass on the outside To make it keep that shape Shark slicer is five layers of fiberglass. This is just three two layers of this stuff and one layer of This stuff between the other two layers Because I want to keep this lighter. I also made sure like down this Whatever you call this the seam I smeared any pooling resin out of there Because you know that wouldn't add a ton of weight, but it would add you know, it's just dead weight having resin down there So I smeared it up the sides. I Didn't wait to get pigment for the resin so it's uncolored. I Was just excited to make it so I made it and it won't it won't affect performance or anything I'll just have to make sure the Fiberglass is painted which I should do anyway, so it's fine. I'm also thinking about making a subfloor Which is something I was kind of thinking about before Like where the pontoon comes to the bottom. It's a point. So it won't be a very good spot to stand Not that anyone has to stand but it would be kind of nice to have a flat thing there So I'm thinking at the bottom Maybe that much of the bottom put a little floor above that and then stuff the middle with bottles and styrofoam and You know if I have that go in the whole way of the boat That will prevent sinking even in kid catastrophic Disaster Unless the boat is like literally severed in half and all the stuff comes out But in that case, there's probably a bigger problem than thinking Man, I've been saying but too much. I gotta stop saying but everything doesn't have to be a butt Not everything in the world does a butt Jamie. Can you can you do some smiles for the camera too? Yeah, smile Where's your smile? Yeah