 Yo, you too. Welcome back to Kenny's TV. Today Epson equal tank 3760 unboxing and Conferring into a sublimation printer. There's my sublimation ink Put it to the side and we're gonna get the printer out the box So we wrapped up in plastic Get your instruction booklet or pamphlet We're not gonna be using that Get your power cord and you'll be getting your Epson ink Get three blacks and the rest of your colors cyan, magenta, yellow And we're just gonna put those to the side not gonna be using them so remove everything out the plastic and We're gonna start removing the blue tape and make sure you check the top Flip the flap take off the tape and we're just gonna turn it to the side and it's gonna remove that piece right there I'm gonna turn it to the back. We've got a couple blue tapes right there. We're gonna Remove and I notice there's a compartment back there. You just squeeze it both fingers Pull it out and it's check inside to see if there's any blue tape in there. All right, there's none and just place the Back together more tape Where the scan is at and we're actually gonna lift up the scanner To look inside the printer a little closer to look at the blue tape And make sure that you remove that So that way whenever you be trying to run your printer don't cause no additional damages Just look around. I'm gonna take one more check. Looks good Check the paper tray, which is the very bottom tray And then there's another tray. That's where the printer. That's the paper that comes out Just plug in the power cord to the printer But we're not gonna turn on the printer It's gonna plug that in and we're gonna start with our sublimation ink and Here's the black one. Just take off the very top and you see that it's sealed and I use scissors You can use a blade knife razor Let's get that open. I pretty much took the majority of it off and twist back the top But I removed the top cap part So your sublimation ink will look like this and this is Cosmo ink by the way So I lift up the whole scanning part lift up the compartment and right there with the blue is that it's gonna We're gonna start with the black And as you can see right there it lines up with the black scion Magenta yellow that's where we're gonna be placing our ink and I found it easier By lifting all the blue tabs. We'll just drain out fill up the tank And it's gonna fast forward for all the rest of the colors. Then once you finish Close the blue tabs to the compartment. I'm just making sure that Actually closed Now we're gonna plug in the printer. We're gonna power it on right there to the screen right here for your language And you can actually slide this out right here and whatever language you prefer Press okay. We're gonna be using English and the process Processing then take a few minutes Not that long This is see the start here she took complete Installation which we are ready. That's okay. Talk about the ink. We already did the ink just hold down the question mark Confirm the tank so it's filled up Make sure you just press okay, and this is gonna take a 10-minute process for your Epson equal tank and that's fast forward And what I did is went ahead and make sure the paper is eight and a half by 11 So I open up the bottom tray Load it up eight and a half by 11 regular paper and Pretty much what this is gonna do a print head test and to get out of this screen, which I had a little bit trouble What you'll have to do is hit the up arrow key see I made a mistake there Went back Figure it out and what's a maintenance? Press okay, and right there is print head nozzle check press okay And press okay for print pull out your top tray And this is where the print is gonna come up taking a look at it real quick See the top left part of the paper Pretty much it's all side of line set for one looks good Thumbs up and I'll tell you on the screen if it's bad or not But this is a brand new printer should have no problems. So I press okay We'll go back to home with the general settings But excuse me. I want to settings Press okay Scroll down and I had to go to general settings and then went to network settings press okay and do the Wi-Fi setup and Since I'm wireless I picked the Wi-Fi recommended press okay, and then press okay to start setup Did you come to the Wi-Fi setup wizard? press okay And fast forward put in my information Press okay, but back to home, and you're done