 Good morning. Good morning and Happy Monday to all you lovely wonderful people out there. I hope you have all had a wonderful weekend and Are ready to have some fun here. I Am well hanging out revealing to you my well Just called my new haircut now those of you who Managed to catch the live show last Friday night on 8-bit Esquire's channel may understand why I have a Lot less hair and a little bit more sorrow in my heart Because my lovely blonde locks Well, they were thrown out with this morning's garbage and I have No more hair So if you want to know more about that definitely go check out my buddy stream That's all I'm gonna say about it. I don't really want you to go check it out because I was kind of a Delusional those arcades here. Well, I was a kind of a delusional mess by the end of that show. Anyway, I Want to thank you all again for being here live today as We work on a very special CRT that is This CRT right over here. That's right Right to my right. It's a 14. Oh five and so This one's one you've seen before I do believe it actually belongs to my good friend Bob from retro RGB and It's one that I worked on for him Gosh a couple times, but it still is an issue where it takes a long time to warm up The only thing that's not been done to it Is it's not been recapped on the main board and then it's not had It's got a bad deflection arm and I've shown off Kai tours new bracket from Kai tour industries and We're gonna use that today to replace the one that's inside of this CRT. That's just you'll see it's a mess it's held together with tape and I'm gonna turn the lights up here in a second But please folks if you could like the pinned message said please just do me a favor Drop a like on today's show. I do appreciate all of you for being here. It is Monday back in the bunker I've got a couple announcements here in a second We're gonna go through and then we're gonna have some fun tearing this BVM or PVM Excuse me a part and I'm gonna do some shout outs here in a second Please if you could hit the like button for me so that the world will know that the bunker is live And I'm gonna go ahead now and I'm gonna turn up some lights now If I pull on all the cameras at once you could see Cole's not here right now. I do have the cold cam active though so If he decides to grace us with some presents, we'll see let there be light Let there be light this good day. Hey, thanks. Oh That's right. All right guys want to say thank you to Daniel Gonzalez. Thank you for coming in buddy James James moon. Welcome back Thank you for coming Belmont welcome in as always Zero sleep welcome back. You guys are great. Giant's orbiting good to see you today. What is truth 101 welcome in delusional Thanks for being here. Dr. Claw. Thanks for coming back. Shin Lark coffee time. That's right. Hang out grab a coffee coffee GA Raffine Sam. Thank you stariana stariana. Yes, we're gonna have a wonderful time DJ zero mask. Welcome in Typhi MC. Thank you guys for coming The train double X welcome in. All right, everybody. Let's get going Feel free to chat amongst yourselves. Have a good time Again, we're working on a 14. Oh five. I've done so many videos on the 14. Oh five I Want to do a follow-up video that's kind of short on to the point of Kai Tours bracket But I'm not probably doing full restoration videos on it But it's a great thing to bring on a live stream Because again, I if you go to my front page of my channel, I think that's pinned is a marathon of just PVM repairs of the L5 series. It's just a playlist of like I Don't know three hours four hours of it. So That's what you can go check out if you want to see more on the L5 and Let's uh, let's go over here take a look at it though. It's gonna take a second here to warm up So that's what I'm gonna do it first off is I'm gonna power it on I haven't powered it on in weeks Okay, and this one You'll see it. It should take us extremely long time For the picture to come up. I mean like minutes So let me get a little closer As long as nothing else happened to it in the meantime So that's powering on This takes a second to get going It's online. Hey, I have a signal going in there And this will just take an extremely long time to come up It should so we'll start the clock here. Let's see. I am at Six minutes and about 30 seconds on my counter and we'll see how long it takes for this screen to pop up We'll just watch it Yeah, this should take a while Frankie Zito welcome in yet is I Need about this crap is always broken delusional. He always tell he always and he's always potted it off on people So yeah, Frankie Zito it is a tough one to get into and service because there's so much crap inside of it It's all compacted So it's it's a little bit more of a pain in the neck to work on So we're just watching it here. We're coming up on goodness gracious one minute like 15 seconds and still no image Well, we'll just see we'll see if anything comes up. I swear. You're right. Bob always sends me this stuff now It worked the last time I tried this thing And it's been sitting in in the shop here inside since let's just see. Oh goodness gracious. Yeah My new haircut, right? It's all gone. That was a fun stream I'm glad I survived it man. I was out all Saturday couldn't move. I was a waste. I was so lucky my wife got I had interviewed for a new job at the They asked her to interview for a new position at the university and so they had been having some issues with HR and they hadn't said anything about whether she had gotten the job or not and they offered it to her Friday Well, I was on stream acting crazy probably shaving my head at that simultaneous point I'm still waiting here Coming up on three minutes. No image man. See like you think this was broken if you just got it I'm gonna still see the All right there just to make sure I'm actually smell see it shouldn't matter I should be able to still see the menu Actually, it is starting to come in you just can't see it Thanks, Koala. Yeah, it definitely should even say anything about my hair The crazy thing was is my head looks so bad And I post a picture of it on on X Saturday my hair was so bad and I was so like hungover I couldn't even handle shaving the rest of it off and So I had to walk around like with a hat on and like a hood and try to pretend like nothing happened And thankfully there was a lot going on with them and oh man We're about to have a picture some point because I do see Start a game if I can I mean it's it's starting to come up. I can't believe it you can kind of see it there See see we're about to see it happen. Look Look at that This is So real time Bam, baby. Watch this Right Steve will just do this and it will magically appear a screen. Now. This is the issue Wow, look how long it took I Don't know that's what we're gonna find out so I'm gonna do there's some caps So I did that I've had other L5s that have taken like not nearly this long But like 20 30 seconds to warm up and then I've Done this cap kit on the main board and I have had success in that actually Reducing that time down to about like five to ten seconds so there is a possibility that Hopefully this will get better from that. Otherwise, we will have to test this tube But I don't know I'm thinking it's It's that main board, but yeah, it looks bad Up with that picture Completely crazy that picture is And I mean it might take longer We're gonna let it um I'm gonna put a game on it and we're gonna let it warm up We'll see. We'll see how long this takes to like fully warm up. I mean, that looks terrible This is let's see if I could reset the picture. I Remember when we started it up From cold before it took a long time to look good So I mean everything else is working on it like you can hear it So what I'm gonna do is I'm just gonna let it run here for a little bit We're gonna try to let it get warmed up before we actually work on it and open it up because I want to make sure that The image will get at least a little bit brighter. Oh, yeah, I Need to break you back. I need to bring you on the show I've been waiting holidays have been so crazy and actually I'm about to have to leave town I'm taking the family on a trip to New York For a couple days right before Christmas. So I won't be I won't be around oh In Finneon, that's not true. We can actually do we can actually Rejuvenate Trinitrons and we have I mean I have on this channel and I've done it on a 1351 queue last month They can be tested and they can be rejuvenated. I actually had one that was Had no color in it and after rejuvenation looked great. Let's see. This one looks really good after it warmed up at at the Convention But I mean I'm just gonna try and reset it and see if that would help any We try the input be I'll switch it over that it's on composite video So I don't think that's gonna improve anything, but we'll see Nothing really different there Now if we take up I'll show you kind of how dim this screen looks better. I mean it should show up good on this 240p test suite Yeah, super dim Everything else looks fine. It's just this really super dim If I go like the color bars And I can see all the colors, but This looks weird just looks weird looks still looks dim It's getting better, I think Yeah, it's probably gonna just progressively get a little bit better each time. We'll just keep watching it and See if it gets any better. I'm gonna give it about I'm gonna give it about another Probably five minutes and if I don't see any improvement and okay We're just gonna we're just gonna begin servicing it Because I want to go ahead and get it apart while we're waiting and watching. I'll show you this is So I've already done this kit for part of it it was the 1405 kit from save on pat and So I've done the deflection cards in it and We need to get into the main board because there are Roughly 10 more capacitors. I have listed here and that board has a lot of capacitors in it nice But it's got I've already built the kit. It's right here And it's not really anything big This is probably the biggest cap is this one 50 volt 220 this is pretty massive one that you can get smaller ones Not too big of a kit It's pretty small one Let's see if Cole's back. I don't think he is Worry is he must be upstairs sleeping Wait for the garbage man, so I'm just like I said, I'm gonna give it 10 more minutes till about Five well six more minutes probably now We'll just keep watching I mean it's functioning Excuse me, but everybody knows why the 1405 is so desirable Right, I think it's looking a little better But goodness gracious Not too great Not to too great Okay, but about two more minutes been about four more to go. So just keep watching this thing Now if you work on something like Hey smesher Josh if you work on something like the Sony FW 900 you actually let it have to let it warm up Almost 45 minutes and here's a little something if you see right here, it's very hard to see it But right under my finger Way way back there in the background. That's the FW 900s 4x3 version. It's like the C520 or something like that Those have to run for a long time before you can even make any adjustments to them They have to literally warm up 30 minutes to 45 minutes and then I had another Now this is of normally long for this thing to get hot because this is 1405 it shouldn't take this long to get warmed up normally so This is not Your normal case, but there are times where you can turn the CRT on and it pops right on After a couple seconds and another time where it takes 15 seconds 10 15 seconds to pop up And that's just the cathodes, you know trying to warm up and heat up. Alright, what are we on the timer 20 minutes? Alright guys Let's see what we got. All right, man. We got an awesome crowd here today. Thank you all for coming back Please do me a favor and Hit the like button if you like my new my new haircut If you haven't already there's my Plug for it. I mean, I'm starting to think it looks a little better. Let's go back to legendary acts and then we're really gonna Yeah Then we're really gonna You know take this thing apart and the thing is I can easily do the neck and the testing I need to do that cap kit first because it's the hardest thing to get to it's all the way deep down in this monitor We'll get it open. Now. This is shadows up here. That's what you're seeing The legendary acts Because that one looked really damn to begin with let me turn that off and see if that helps Yeah, I mean, I'd say it's better You can definitely see it though nice Alexandra All right, let's So it is getting a little better I think that if I kept letting it go the thing is it hadn't been told this was dead cold like not turned on for Months, so that's that was a good thing to see because if I turn it off Let's power cycle it watch. It should it should show the screen pretty much There it turns off turn right back on It shouldn't take nearly as long for this screen to come up, right there. It says see now. It's warmed up So there could be something in the power block. I've really got to do this kit from Pat It's just got to be done. So let's do that and again if it's the tube then we'll go from there We'll see we'll test it, but that might not hit done today. That might need to be a one for the next one So all right now I'm gonna show you how to get this thing open. All right I'm gonna show you how to get it open Turn a little jazz up a tiny bit There we go Here we have Six screws on this side all of which need to be removed. Hey, Ronnie. No, you didn't miss anything yet We were just testing this pvm and what is going on with it is it takes forever To warm up and actually show an image I mean it took Now I can't remember. Thankfully we recorded it on them Anybody can remember they could put it down in the chat, but I can't remember the amount of time It actually took for the screen to pop up, but it was a long time It was like I think it was beyond six or seven minutes and then it took another 15 minutes to get a decent image. I think it would have gotten better if it had been running for an hour But it takes a long time for this one to warm up. So there we go Nothing has exploded. I'm sorry now No kabooms yet, and this one's dirty goodness gracious You know Bob sent me one BVM one time that had That opened up and usually I open them up in the garage for this reason Like it had like been peed in by a mouse or something in The bottom half of it. I had to take the whole thing apart and clean it I don't even know if I told him about it. I think I just cleaned it up and didn't even mention it But it was in New York City and then it's storage so I can imagine that happens BVMs have a lot more crevices in them And I've had problems with mice in the past with my own CRTs Alright, there we go, and you all knew that Gosh, the rat was in my shop Last last year. Yes, master. This is his PBM It's Bob's Now there's two screws on the back And that's it Oh, come on last screw. Gotta get this last screw out of here. There we go. So you don't really want to take off that You don't want to take off these rivets at all. You gotta be mindful of what is around, but that's all you take off Look how quick that was that was about the quickest quickest disrobing of a PBM I've ever had on On live air. Alright Look at this, look at this arm Maybe maybe I can get some light and zoom in a little bit for you. Oh My goodness, look at this. It's gonna get a little grainy, but it's okay This is a piece of tape electrical tape. This is not good. As I said, I've already done the cap kit on this board Look at that Because it's it's broken right here. See this isn't that fun And You might say what fool. Hey, here it is What maniac do you think would actually just have done that taped that in what kind of lazy lousy service, man? You think did it so that was a problem. There really was no good solution to this till recently You just had to keep it together at all costs and That's really harmful about that, but it's not good So but that's that's kind of the reality of working on old hardware sometimes is Yeah, so that's what that's the actual thing Ronnie watch We get this. Let me get us back down to size here. We're gonna replace this with kite tours And then also I have to get that bottom board out so to do that I really should just remove all this stuff anyway So that's what we're gonna do Is I'm going to lift this up and maybe do a little bit more of a downward view So you don't see so much table edge there I can't really get rid of this part That's a little better So we're gonna watch this. Yeah, that's where we first came from was the first But I'm absolutely terrible at 3d print my 3d printers. No good It's thankfully my friend What kaitor made this and I've shown this before but this is we're gonna install today Okay, it's a nice heavy-duty replacement just for the same Same thing same size same build out 3d printed really nicely printed and he's selling these over in his website for $30 And they are amazing. So if any moderator and Belmont if you want to throw a link you can if you got mine, but otherwise I'll add one to the description After I get done publishing the show This is really good. This is the Bracket we're gonna install actually Belmont. Don't worry about it. I know you're cooking breakfast Yes, thank you Daniel So that's what this is gonna do right this is gonna be a replacement for this it's gonna sit in here You have this board on this side going here and then there's a backboard back here That's not I'm sitting there and that's That's gonna do that and before I do that I'm gonna remove it And I Need to make sure that I disconnect all the cables on here Cable and I don't to get this part out. I don't need to discharge you yet Okay, hey stuffer stuffer. Welcome back. Welcome in today. Here we go So there's a screw generally speaking. There's three screws on this board. There's not usually four installed I'm gonna take them three quarters of the way out Yeah, there's only two actually this one because the bracket is so bad Just gonna back them out a little bit and then I'm gonna disconnect all the cables now I can get the deflection card out Gosh, this thing is just wanting to fall apart Come on. All good Screws are down here and this thing is in bad shape The problem is is this bridge this plastic It's not just the fact that you know something happened or anything It's it's this plastic. It's just always been brittle And when I pull this off, I'm gonna snap it a little bit and show you what I mean Like this one's all good It's the one I've done Gosh, who knows how long ago fine on it. That's the board I did before and Yeah, this there's a D2 card on here Normally you really don't do anything with this card. It's just got a couple of inductors on it but Purpose of this Shall remove Okay, now I'm gonna be able to get this whole bracket off and we'll bring it and this board This little D2 board should come with it and that way I can get it out easily There's only one screw holding this bracket over here next to the flyback Main board see this main board is a donor board That we tested at Retro World Expo because the other board was busted. That was the problem now that I remember it I'm remembering but this has been so many months ago Remember it's just unfortunately not what it used to be but It had it wouldn't even run for more than a couple seconds without shutting itself off So there was a problem with the original main board without a donor board installed that and this one needs to be serviced the donor board so this is the little D2 board and it's held in with plastic It's not got screws little pop-in things. I'll show you those closer This isn't here like this. Okay Show you we're gonna do here Look at this. I'm gonna go to my face only. Okay Back out a little bit there we go and So this is the other side of that bracket, right? This is Bob's original bracket, which is not nice so I've got the D board here. I've popped it out and I just need to install It's gonna go Right back here on the new bracket. Okay But in order to do that, I have to put these little plastic pins in here Plastic snap-in things and I think I should just be able to pop them out from the opposite side with Just some pliers like that you squeeze it. That's it pops right out But so you got to match it make sure you do it the same way that It was before so I'm gonna snap it in there like that okay, and Where this Are these pieces on the inside you get to see all this? I'll show you to you what it all looks like when it's when it's actually finished here and Then we're gonna I'm gonna show you how brittle this original one is and this is pretty much the condition for all of them now so You know just the fact of simple thing of getting this serviced and And this is gonna be part of probably something everybody's gonna want to add to their servicing package Now that I can get a good stable supply of them because again, I don't have the You know, maybe one day I'll be able to 3d print them. I guess I probably could that would be smart of me to do it But like I got one it just can get it going So there we go All right Now let me show you Because they are opposite of each other right there They run opposite and watch this Then you can just stick your card on there a little d2 card And that's how it goes it's in there and then you get your connection point up top like it's supposed to be and that's it Perfect fits perfect right there So that's you know, there we go good shape right there Nicholas I am waiting. I don't currently have an L5 in the shop I believe it's the exact same size But I haven't been able to verify that with testing it to fit because I haven't had a 20-05 here yet So it's a great question 100% will work with the 14-05. We are not sure about the 20-05 literally waiting to get one in the shop Unfortunately, I thought one was coming, but it was a 20m for you. I got so many coming and going I forget There should be a 20 L5 though in the shop at least in the next couple months So I hate to say it lasts that long, but if anybody else wants to Confirm it they can really great stuff So thankfully we have this Let me show you this original piece now. I should wear eye protection or something Cuz this thing this thing's a mess, you know, hook my eye out this little piece of plastic just fallen off it already and More tape This is super duper like what I mean like doesn't take much. I don't think what let's see Let's see. Oh my gosh. I'm gonna glad I wear an eye protection See, I mean this stuff is just like brittle. It's like peanut brittle. It's so brittle. Just see that look at that I mean, I didn't even put any pressure on it and look at how it just felt it just pieces apart like again like oh my gosh If you're wearing 3d glasses today, you would have just gotten a projectile thrown at your face So that's the that's the issue. I mean look at this thing Yeah, that one that edge is still strong. Anyway, that's what's All right, enough you get the point it's garbage It's garbage It doesn't taste like peanut brittle unfortunately, but the dog might think it's peanut brittle Dropped one too All right, I'm gonna go trash this But you get the point No good It's no good. So here we'll go. I Thought Cole was over there I hear ya Alright, let's get this Next up. I'm gonna remove the neckboard Again for convenience and get it out of the way, but it also has been serviced So it's not It's not the issue It works It works to get it out. Let me go back over here to To our desk camera since Cole's not around And we go so we're gonna get this neckboard out. We're gonna pop a couple of Things open here get this apart. That's how you get this neckboard out. And this is what it looks like Inside of there. So it just pops out. There's There's a tab on each side Tab right here and right here Just you know slightly put a little pressure and pull it back to release it All right, you go set these boards in a safe spot We do need Any, you know, I'm gonna have to do some things Some cables and stay over here pretty much all these The ones that I have to disconnect are all the ones from the input board So I'm gonna disconnect all these cables right here and I'm gonna pull them out of the way Because I'm going to take the main board with the input board out from under here And I'm gonna kind of move this up and have it out floating So that It doesn't I don't take it out also It's the best way to get in here. You do this board that I found There are gonna be some screws So what do you think? Do you be able to take this apart? Hey mark, don't get too excited. This is still Bob's you're the next one up after I get this one done The next The next of the pvm l5s I actually put together your cap kit today for it And I have a bracket for yours if your bracket is busted at all From kai tour so we've got it all going on buddy and could think of do hey Why hair go bye-bye? Oh Oh, that's a long story, you know mark you kept saying why weren't you guys drinking that night? I drank way way way way then voltar showed up in his underpants It's for the children What a fun time this needs to go over here This can go up here for now because I haven't discharged it yet. This can stay over here. I don't want everything to get all confused There is See I want to make sure I get some of this stuff out of the way down here on this side by the flyback There is a ground cable that you need to get out of the way Just releases by clip right there There we go It's got to be gone and usually there's a screw down in there, but I took it out already I think there might be one more screw down in here somewhere You'll see we'll get this and put board out of the way and we'll see So next up, let's move it around A little bit closer This one's held down here by these three screws So we need to remove these three screws Remove two of these and I'm gonna switch around and remove the ground screw and This this Side doesn't seem to have the trouble. I don't know what it is this one is still the same plastic So it can be brittle, but it seems to hold together better Maybe the fact that it's not You know holding the weight like the arm is That was a lot of fun. I want to thank all you guys too for going out there and man really showing up and Donating and everything you guys really helped out for good cause and Thank you for that Yeah, the congratulations you were able to grab a retro tink 4k awesome Merry Christmas, right? All right, so there's all those cables out of the way There's one more kid one more screw right here where my finger is I know you guys can't really see it too closely, but you can kind of get the idea that I Don't know if somebody wanted to come back and just randomly watch this and take their 14-hour five apart. They could probably kind of do it from this Video Just slide up and out of the way so the idea here is Also to release that cable up there. That's that's my tally like cable plugs into the top Okay, I don't want to have this busting anything else That's what we'll do there Get this over here. All right. Everything's good Excellent, so that's that's all this whole side now Right Just get it out of the way, okay Now we don't have to worry about it And then I'll just connect the cables to the front which are the power button And the de-gauze are right there. Okay, take the pressure off that point It's connected to like the the actual button boards and stuff on the sides And let's see what else we got here. This is gonna stay. This is the yoke cable. This is going It's the flyback which you can see we haven't even discharged yet Still about to do that Rest of these cables are staying. There's gonna be a ground cable somewhere. I know this one Okay, there's a ground plate right here All the cables Can stay with the bundle Well, actually, you know what I can't take it as a bundle. I forgot there are screws On the main board, so I do need to remove this board now that I have the chance. That's not the way So I'm actually going to remove them from the main board instead of from Instead of from the input board. I'm going to remove the screws. There's two And this is where they go one goes to the input board Ground one goes to a neck board ground And the other one goes back to the main ground and the Front of the monitor Now all these grounds loop together just to give it a good grounded connection there between the monitor All right, there we go. That's been removed There's A connection. I need to disconnect there for the power input and then there's one more Ground cable that I have to move over here Right there Here we go All right guys, don't forget when you're coming in If you do any favor, please hit the like button We're gonna get this I'm gonna get this out of here Careful with the stakes, man There we go. Please hit the like button, baby For the sake of the 14.05 Here's an input board. I'm gonna go set this somewhere safe. All right, you know what's next Let's see Let's see if we can do our best Electro boom here I know that How close I'm getting into this Let's see Well, maybe if I move it Right here, I need to get closer Ooh Look at there That's better Oh, yeah Frisky up in here Okay Now this PVM should not have any spark to it But hey, don't do this at home. Just look crazy people like me do it I didn't connect the discharge tool because this Is a pvm and it has most likely got Self-discharge, especially this l5 But it has if it wasn't If it wasn't discharged, it wouldn't be discharged yet. Let's see if anything happens here from the anna. I doubt it will No, nothing And I mean we could just take this Ground that to the That's too short Ground that to the plate right there On the side, nothing But don't do that at home kids. I'm just the crazy guy And that's That's why I have no hair Because I'm the crazy guy and I have no hair. No, I didn't go all the way down, you know I didn't go all the way down to Stone cold steve austin level shave head Couldn't do that. I would have been a real Real doo-doo if I'd have done that I think I got it down to a two guard or something And this bundle is connected to the right tone Yep, you kind of just, oh man, this is something that's there's so many connections in here. All right, that's almost all of them Might as well leave them all connected. It makes it easier to put them back together In the right spot kind of It was there All right goodness Look at that. This is the main board Right there Yeah, if you want the patreon link, it should be also in the description of this video. It's in the description of every video All right, take that out And this is what we're actually looking for This is what we're looking at This is what we want to service Is the heart Of ppm. So I need to get some things separated out And yeah, we're hitting it at the one hour mark. I appreciate your patience everybody We kind of did that experimental phase. It took 20 minutes testing The interesting thing is it's like if you would have just gotten this and turned it on you might have thought it was dead, right? so dead and Let me let me go put up here. We're gonna look at this again soon, but this is the bracket I'm gonna go put this over with the other cards Just to keep it out of harm's way But yeah, man, I should really gosh. I mean so many guys out there. I know you're already on the patreon stuff I really appreciate everything. I'll be honest with you. I could not um Big cost $3,500 good one Uh, I'm super thankful for everybody on patreon. I could not do this without you I uh, I don't have any like real sponsorships for my shows or anything. I have It's just patreon and then the work I actually do and this is my full-time business self-employed job that I do now Is just work on these machines and study them and then refurbish them and restore them to for people And so that's what you're supporting is this show this entertainment All this knowledge going out and helping me learn helping everybody else learn And I do have aspirations to make things go as big as I possibly can With things like tutorial classes and things come in It's just hard to do everything all the time at one person But I have had You know a very good year. I have a lot of look at this. We still got plastic pieces falling out of this board From that bracket I've had a good year where I've had a lot of people come in and get their kvms restored. I have a good wait list currently More pieces More pieces So we're gonna get in here I want to switch this camera from kind of being That View to overhead view. Okay I'm gonna do that. I don't want to give I don't want to give everybody out there a headache But You can preset up a little bit You can do this one Gipper skipper we're gonna move this guy out of the way Cole has not been in show today. I don't know where he's doing man. He is He is not hanging out with us today. He doesn't even know it he's upstairs probably snoring on the couch Waiting for the mailman to come So this this has a lot of our power Stuff in it I'm just getting this all fixed Okay And I've been trying to find a better camera than this but No luck so far yet The one I wanted is on Again, it's on like a pre-order or something. I'm not interested in doing that with launch tech So this is the board you could tell it's tons of capacitors in here. Okay The ones we're going to be concerned with are going to be kind of a pain in the neck to get to There's one There's one no joke. You can see it right now It's You point some of them out to you This is good Right down in here See that one we have to get this one out So I need to remove probably this part right here I usually remove it also just to get that capacitor right there out Okay, and then like it's all the ones that are tiny In this kit I expanded a little and usually I replace all these one two three four five Sometimes six depending on what this one is Take the idea that I'm going to get to 164 Yeah Okay So here's uh, we're gonna do we're gonna go through now and I'm gonna I'm going to retouch up the solder On these parts because this is also a board that gets The that's that runs a bit hotter Um, it has a higher tolerance for heat generally So I know Which capacitors we're gonna do I'm gonna try to get actually let me see I don't know that I have Markers, but I don't think we need them We'll need probably this It's like all these clustered up in here we're gonna go ahead flip this over and Do what we do best, okay? We're gonna start with this cluster. We'll get to the harder ones after we get This cluster Right in here Relief load got my uh hacko Iron here up to 650 degrees Fahrenheit my list right here Let's see. Let's see if we can get everything situated Without burning my head off Let me move My microphone up a little if everything's going well out there. Thank you all again for being here Well, let's go. Let's get frisky So 611 is absolutely on the list. That's this one right here I'm flooding it. This should just make it Simpler when I use my fr 301 to remove These capacitors, okay 619 I Do remove that one also Because if you look in here, I mean goodness gracious, there are so many Places traces down in here. This is not the simplest board to work on C662 is also on the list and there's like two more over here that get removed also gosh These also have very large ground plates and that can be an issue A little baby. Give me that solder And see when you do this it also makes it kind of easier right to see which Which parts you're replacing those three 624 is on the list So it's that one 606 616 6 6 Sorry about that. Sorry About that. I was reading this list and Losing myself. So these two over here apparently not in the list 606 616 are not on this list 50 volt 100 That is 50 volt 22.2 50 volt 2.2 I'm probably going to go ahead and change these two also Just for the heck of it because they're right in here too. I don't think 609 That but so there's there's those three. There's this big one. I need to do and then there's these two over here All right, let's let's go back here and we'll look at them 624 624 is right here. Gosh. It almost needs to be hotter than this It's crazy, isn't it? There's 624. What was the other ones I said these two over here? Man these are like C606 There we go So that's this cluster And that's about half the kit. So what I'm going to do now is I'm going to Actually go and I'm going to fire up I'm going to fire up the fr 301 We'll remove all these right now So if you want to know more about how to like maintain Your tools I actually just did a recent stream on how to do all that clean up and Maintain your tools if you happen to have these Into the year a good time to work on that kind of stuff Oh, yeah My esd strap go strap in, you know Go strap in Make sure everything's good letting this heat up I can hear it sucking Let's get one of these. Let's get this easy one out My finger on 624. Yeah, I got one leg free But the positive leg did not come free That's not a problem though It happens. Where are you? Where are you guy? Right there Right here This leg is still in there. It's still attached. It just has all the solder less the solder gone Just float over there in that one again. All right. I think that's good looks like it Yep, it's broken free Was the other one this is just you know, this is not the easiest board to work on First tooth has been pulled 50 volt 220 Put it in the bad caps Collection over here And then I need to remember to write the other parts that I've added That one did leave a ring around it. So there's a very good chance that capacitors dried out All right, let's hope it was now we're going to go in here I'm going to check out our These other three up top that I first did the Soldering on you see him And maybe I can do this For you goodness There we go Sometimes they want to be stubborn now you could also do this trick Nope, there it goes. No tricks needed for this one 662 There's a loosey-goosey down there if you can see it I'm just going to leave it in there and we'll pull it at them Together the slow hand right that one's loose Yes, okay our three amigos our triplet of Capacitors here about to come out I hope that view wasn't too terrible. I know it's not probably the greatest but I'm about to just remove all three of these at once So I'm going to confirm that they are what they say they are on my cap kit. We've got a 3.350 bolt here 662. Yes, that's what the cap kit says If it's different from what the cap kit says, I'm going with what's on the board. Okay Unless it's specifically mentioned to change and upgrade the part next one is 619 619 is a 54.7 Yes, that's what's on here Yeah, I will Yeah, play for it. See how these look after this 611 in the list It says to replace it with 100 volt 47. My goodness. That's not going to fit down in there Yeah, it's too big. I think we're gonna have to just not replace it. It's actually a 25 volt 47 So we might just go down to a 50 volt Even though Pat wants us to go really high on that voltage All right, so that's the first four and I've added I've added 616 and 606 to the list so I need to get Something to write with Give me one second. I'm going to go get something to write with I'm going to add this to the list Here they is Okay, so I'm gonna say on the Main board right here 619 What's up rollpads? Absolutely. Okay, so I'm going over here. I'm adding C6 0 6 and C 616 616 is a 50 volt 2.2 and 6 0 6 is a 50 volt 100 Micro farad capacitor And now they've been added to the capitalist We'll remove them just like the others. They've already been reflowed. Those are the two that I reflowed They're just so darn difficult to probably get into that nobody wants to mess with as much Make sure you have the right one here Let's go to the bottom one first Come up pretty easily This will be much more difficult on this particular board if I did this without Without actually Adding that fresh solder Because this board is just it's got thick traces. It's got thick everything And 5100 for the 6 0 6 like we wrote down This is 52.2 Both common capacitors that I'll keep in Stop. So there we go So that's oh about half the kit just under half So we've got we went through four on there added two that's six Now we'll be The next one I'm going to do is this hard one down here in the middle. I know that one's on the list So again, I'm going to do here. I know this one Up here is on the list This is six three four Right where my finger is you know here And then we've got this resistor this resistor right here. We're going to remove okay So those are we're going to remove both of those and that's because I cannot get to that capacitor Without removing that resistor. We're going to get that resistor. We're going to remove six three four We also have to do six five eight, which is right down here where the rest of these parts are I think they're You know, uh patreon services, I'll be honest with you right now. It's about 70 dollars an hour for labor rates This kind of a work on this particular monitor restoration package Generally runs About 600 bucks really and then if you do the if you do the Other things it just adds a little bit more like I don't charge really Anything to install the new bracket, but if you buy it you have to pay for those parks and stuff Because I'm already in here Doing this But most of those most of the full like restorations you see where I do not just this like all the other things I've done with the neckboard restoration and the Other services. This had a couple of other things done to it So much Of that I've had way too much solder on that resistor Let's get this hopefully got all that off of that This is coming out So we're going to do the text side towards Our text side away from the big shell rf shell. Okay Right there. Okay, let's set that aside because that's going back in. There's nothing wrong with that part But you have to do that to get look at this. This is where the capacitor is right here So I couldn't get my fat finger down there easily get in here 634 Here we go 50 volt 10 634 on the list 50 volt 10 now here's something interesting if you look at pat's list Sometimes we'll make mistakes So you have to be careful man I love him, but He wrote down there was a 50 volt 220 right there and I've done this cap kids so many times But it's definitely a 50 volt 10. I just pulled it again. You can see it right there And that's too big of a change I'd like the worst congestion All right 1603 comes out also I believe right? Yep. I don't want to say the rest of them are down in this area 656 over here Isn't it random it's like this one 655 or 656 only This is just 656 comes out 1603 1601 which I don't know exactly. I believe that's one of this is 1601 down in here Both of these Yeah, no, that's yeah 539 Does not appear to be on there 57 No, just 508. Okay So like there's not a lot in this cap kit. We just We just need to get out the ones that are on the list We shouldn't be able to get Let's see. Let's let's go ahead and reflow solder on a couple of these others and then we'll do like three at a time And then we'll do our last one. We've got 658 already reflowed 1603 So Seven so we did the five on the list added two so we should have five left one two And then 1601 up here and we'll have two more 508 is somewhere around here right here It's 508 656 and 658 three 658 656 is the last one So we'll go ahead and we'll get these ones and we'll find that last one at the end I'll just fill out All right, let's do those three out of here Get those three out and I'll do that last two. We'll find The last two on there. So this was 1603 50 volt 10 Yep There's this one. That's the one we haven't taken out These two down here came out. So that's three total out the last one's over here. 656, right or 656 Yep, right over here. You better remember when I saw it. So I saw it. Sorry guys. Let me pull this out a little bit this one 1601 a 16 but 100 508 50 volt one micro farad. Hey 8-bit Esquire Thanks for the $20 super chat stud Yeah, I didn't know uh, you know, I thought maybe maybe I got so crazy the other night that nobody was gonna want to be friends with me anymore I was like I might have ex-communicated myself uh With my rash behavior I mean, I honestly don't remember everything Yeah, I know I just remember Joe getting me really bad too. He went savage on me That was fun. I think that that should be uh an annual thing my uh Not not that particular thing but an annual thing for you know us to get together I sometimes I feel like I'm the like I'm such a jackass in the community. I don't understand like How I get away with it 656 right here Right down in there and then like six five eights up in here. We gotta get these two out. But thank you Roger You're the best Dude, I probably was I don't even remember that after show very much I mean, I don't know Yeah, I mean, it's luckily that the camera didn't keep going All right, here we go Yeah, I mean, uh, try to have a good time and sometimes you have too good of a time Golly, I hope I wasn't too big. I mean everybody's probably laughing at me now That's what they're gonna say. Steve in the after show good grief Thankfully that was not going anywhere. I mean unless Roger's just you know, that's the thing Roger now probably has blackmail on me forever. I'll have to go do whatever he needs for Any case he has ever in the future Great didn't even think about that I mean, I haven't been that hungover in a very long time and I've gotten myself hungover a couple times this last year But that one was a special You're you're you're sworn to uh privilege with me anyway, you know That's like It's like the um fear and loving stuff, you know Maybe one day we'll write a book about it. I mean really Some of the stuff we got into Just wasn't right. I got into I was like, what the hell was I starting? You know the steve vortex. That was too good Too good Last capacitor here. Yeah, the live stream is up on the channel over there. Um James I know he does have it Because I went back and checked to make sure it was still there. It certainly is Didn't get him banned. I don't think that We did that bad You want to break three Here we go. Whoops 16 volt 100 658 Excellent A little bit extra for bob two more extra them was in That was in his kit originally now the first thing I'm going to do is go ahead and replace this very first one And get this vacuum out of here though FR 301 is done. Oh gosh mark. I know I should not have drank that much of that whiskey. Holy crap. This stuff is too strong I was like I was probably like, you know, I started to think that I ended up like, you know, have you ever seen the Um movie with zek gilla finakis and uh Will frail where they're both trying to become I don't know. It's some kind of like election movie and Uh, one of the nights Will frail's character gets just blasted because he comes over and has a conversation at the home of Zach whatever the candidate name is it was hilarious, but he just gets him totally trash on single barrel bourbon And then the idiot will frail goes and tries to drive and gets like, you know, pulled over by the cops And it's pretty hilarious because he has himself painted on the side of his car like he's driving since he's a candidate So he rolls down the window and he's just shit-faced, but it still looks like him because You know the paintings on it. Anyway, somebody probably knows that money. Uh movie Pretty funny stuff, but that's how I felt Here we go The first capacitor over here 6 34 Is a 50 volt 10 So we're gonna, uh, replace that We're gonna need to get two more in the cap kit 50 volt 10. There's a few of these so this is This is our replacement that i'm gonna be sticking down in there Gosh, even this isn't gonna be easy to stick down in there Even this isn't gonna be easy to do Without that Now I don't know that actually hang on Well, yeah, we're gonna clean in there a little bit first. Hang on This is swabs Oh, yeah, I'm sorry james. There was a pretest stream because it almost screwed me up. I kept going to it also and It was his first stream though pretty good for first stream But yeah, it was He did try to do a pretest stream, I believe Got them all rubbed. Yeah, they do. Oh, hey, Keith Yeah, somebody did go in and reflow them or something I'm gonna hit that up and a couple other points Before I put this back together. I'm gonna Do that. I just don't want to hate having this stupid resistor out and being afraid I'm gonna forget to stick it in there So Let's get this first rivicon placed in there Smaller hands, let's get this one. Let's go ahead and do the cap first and then maybe And maybe I'll be able to do the other one. I just noticed Check it out Our buddy you can hear him snoring An old coal has arrived So there you go. There's a good reason to drop a like if you haven't done so already Please drop a like folks There we go That one's nice and good And we'll go back to the desk here I gotta look at that Joint right there six three four I don't know if you can see it This needs, I mean obviously it's gonna be cleaned Maybe now I can fit that resistor in there. I don't know Definitely my least favorite part is One leg in there we go that should be both in there. Let's see what we got here. Oh, yeah Excellent There we go. There we go Replaced baby That's the trickiest one, right? Okay Because it's just so deep down in there I mean, you don't really get any Uh, I don't know that I think I just figured that out. I was like, well, I can't get my finger down in there Really difficult. I might have changed it once Is there a beat? Oh, yeah, the beep does come from my end. Yeah, sorry. It's my um an ahako machine every time the When I remove the iron Like it goes into a if I put it in a in the uh Holster it goes into a sleep mode and it And then when it reheats up it goes into Hot mode and then when it hits hot mode and it hits the temperature it'll beep So it tells me by audio. Hey, Tony How are you my friend? Welcome back Hope you've been doing well Last time I heard anything from you. I think it was on like my life in gaming stream You put a shout-out talking about playing mario 64. That was awesome On the uh the new little Trinitron right last video All right, we're gonna go in here. We're gonna start filling in the spots We're gonna fill them in I do need to get those two over there, but we're gonna go ahead now and Right down in here. We're gonna get We're gonna do six five eight Which is a 50 volt 100 golly. I see This is where I'm just This is such a fat capacitor. Can't even go down in there And this is one of the smaller 50 volt 100s I have Okay, got it in there. Let's make sure it can get Only down in there. Well It's definitely gonna be much more durable Than the previous small one Okay And once we get this done, we'll go through and hit some spots up with some Zodder there we go six five eight Has been installed looks good six five eight down in there. Like I said, I mean it's pretty wild to put a big 50 volt 100 down in there Thanks, John. Thanks. So Ronnie. Sorry. I had uh actually went through and added about a new hours Hour and a half's worth of jazz. This is like a four hour jazz playlist now some new stuff on there 1603 we will replace next with a 50 volt 10 and this is gonna just It's gonna get easier and easier. So we're gonna do it. You need the long legs here to get these guided down in there Fun little project. All right 50 volt 10 bend those legs down I'm gonna do this cluster kind of at once This one took an extra and again this one had a hugely long warm-up time Now the thing is is It's gonna be hard to tell. Um, I could change all these caps Fired up and it works fine and then we won't know anything till kind of I have to let it sit Probably till the next time we stream Kind of deal. That's what I have to do Right All right, I'm trying. I gotta think about what I'm doing here before I do something silly So 1603 let's do 656 since it's on the other side 50 volt 10 Down here and then we have 1601 and 508 That's Yeah, that's it for this Area so let's we'll do these two Real quick and then we'll do the Then we'll do the other two and then the final Absolutely always check your polarity when you're installing caps Double and triple check it and actually what I do Is I go check my work afterwards. So you're gonna hear a beep real quick. Listen When he gets to 650 There it is. That's just the hacko. Let me know It's at the temperature another way though If I'm sitting here, I know that this is the positive Spot right here that I'm welding For two reasons first off. It says positive on this side of the board But it also has a and then it has a longer leg Same thing on the subtle one They don't always face the same direction, but more times than not they face the same direction caps will on the board Not always though, there's plenty of times where they don't Attack weld these guys in The 656 1603 Hold this so I don't have to let it cool down. I'm gonna trim the legs And then we'll come back and touch up the solder and give it some Think it was good. Well that dog snoring. Okay, there's one 1603 Well, they're just caps that don't have any polarity snuffer stuffer. I don't know what you um Like you just have to order bipolar capacitors So they don't have A negative or a positive end on them As far as like technical makeup, honestly, I don't know much about that I would really refer to looking at it something else. Look at all this dodgy stuff over here It's crusty a bunch of flux left over there. Hey, shut up. Ask and jake man Sorry if I missed anybody who's come in I'm just over here busy working away. So I'm gonna get that. I'm gonna touch all that up too Okay 1601 and 508 1601 is a 25 volt 100 508 is what a 50 volt one Is over top Oh, yeah, so the bipolar cap will not have I'll show you a bipolar cap here in a second It just doesn't yeah, you don't want to use a cap. It's just a different part really Um So you don't really want to use them. I think here's a way you can make a cap maybe into a bipolar cap I'm not quite sure about how to do that But I will show you what they look like they have no band and they generally say bp on them the problem is If you get and then and then on the board there will be no markings because you can put it in either way It's like a resistor um So my guess is it flows through the same way on each side. Okay, just like a resistor would The other capacitors I don't know if they're considered bipolar, but you know the bigger chiclet Capacitors they don't really have a some of them don't have a plus side either So they just are going to be generally a solid color and they'll say bp on them And unfortunately the service manual like I say will not tell you It'll just say the cap value the same as it says for any value So you can get in there and That's why you have to go by what's on the board You have to look at your boards when you're making a cap kit as opposed to just referring to the manual You'll miss stuff like that And you'll find out eventually because you'll go in and you'll do the work and you'll realize you've pulled a bipolar capacitor And you just don't have one you have to reorder Single cap which means you're paying ten dollars for one cap because you're paying for shipping And then one capacitor It's really frustrating All right, that's those two check check Check check check that's five All done that leaves us with our final Six up top Bipolar caps won't have any banding Let's see Yeah, here's one So this is one it's gonna be hard for you to see it Let's see if I can get it to focus This is 50 bolt 2.2 bp So this is bp under it and you notice it does not have any Now one leg is longer, but where it would be like negative marked. There is no marking It doesn't matter which end you put it in even though one leg is still longer All right, we got to get the two capacitors that don't have Here is actually a 50 volt 100 and a 50 volt 2.2 Start with those And then we'll add the other four. I can barely see Anything so I imagine you can't see much right this second I promise it's going down in there Now always go with what's on the board if you're ever in doubt because especially if something's been functioning You know when you just do a preventive maintenance It's always safest to just say See what you've taken out Put that in like for like Too done for to go. Hey a little pig. Thank you List for a 33 20. Do you mean a 33 20? I've never even heard of that one. Oh my goodness No, I don't I've I've worked on a 32 30 Is that what you mean? Man, those are expensive. I got a bright guy bringing one of those soon. I think he's supposed to come here tomorrow What is 11th? Yeah, always pay attention to the caps for sure on the bipolar stuff But yeah, I don't know little pig if that's There might be some documents on the 32 30 on there. I don't know. I only did one and it was so many years ago If it's is it's on the discord if I don't have it Then I could possibly get it done for you for uh, but it will be a little while um Because when that guy brings it in I'm gonna do a cap kit on it It's got to have a vertical deflection thing and yeah, that's an expensive job I mean the problem is is there's like seven boards in that crt. It's huge It's like the it's not it's not it's easier to work around Because it's so big you got a lot of room But darn gone it if it isn't It's crazy. No Second one second here I must have messed up on something right 611 No, this is 611 coming up Because this is the one where I was like, what is he thinking telling me to put that huge cap in that 611 spot? all right Because this is what I have left. I have one big spot I mean Somebody's got to recap it eventually Just being honest give him an honest job and cap one board at a time man. Tell him. It's gonna be like $1,500 That's what I tell somebody to do that Entire one it could be more I tell them it's gonna be hourly and they would You know If somebody wants to put that kind of money and they need to have some kind of financial risk in it because you don't want to Have to do it and then they're not pay So I would definitely recommend you taking a Request and a down payment that seems very logical 624 is the 50 volt 22 that should be fine 220. Sorry Okay One's good Yeah, I got somebody who really wanted me to work on a 36 inch. It's in the garage right now too And a 32 inch actually I have two out there right now very large Guys have been on patreon for like a year and Waiting it's so hard to work on those large ones, especially now now that it's cold outside Maybe it's cold outside So I really can't work Big jump like 30 degrees or lower most days. So this is 50 volt 3.3 662 right? Thank you. Thank you. Sure. We have another Okay, it's two There's only a couple capacitors left. So it's gotta be a 50 like Hopefully it's a 54.7 right next to it 619 is that what it is 619. Yes And I got the big one which I guess I'll just wait till the last So I have to try to get it in there because it is in my ass We'll do these other ones first My favorite uh, Bing Crosby's Christmas song is the duet with The duet with none other than David Bowie. Did you ever see the uh Another welfare reference and John C. Riley and they did that Funnier die redo of that. It's pretty good. It's like everything under the sun hasn't even done You can't do even comedy routine. It hasn't been done before Please leave a like for me parumpa pump pump a beggar for likes All right, I'll take these I'm gonna touch up the solder on these and then we're gonna install our final Capacitor and we're gonna touch up some solder It's a final countdown So Yep, my hair be gone. Oh no, sorry everybody here comes the Comes the boiler Yeah, it's the boiler's kicking on for a minute. So what I'm gonna do is I'm actually gonna turn my microphone on mute in a second And then I'm going to uh turn the music up a little bit more as I finish out You can watch me reflow solder on this board. Thank you for bearing with me folks Five zero eight the jazz songs are from Epidemic Sound which is like a company you pay for background music and uh sound effects and stuff for videos generally and and I just use the their jazz I find their jazz music It made a big playlist of it That I pay $15 a month and then I can go on there and use their music on any of my stuff This is hideous. This is disgusting Oh my goodness, it is gross. Look how nasty gross We're going to uh I'm gonna remove a bunch of this It's just so nasty Keith was right if you're still here Keith You're right. This is crusty and gross I'm gonna do it one at a time Goodness gracious Green then we'll go through here Goodness gracious And let's continue on yeah, it's flux and a bunch of nasty like Just too much flux It's like a flux paste or something It's something I really don't use on this kind of application Goodness gracious That's what's smoking and then you don't even clean it off, right? All right gross Look at all that flux. It's Sucked right up into that And uh flux and sorry solder So we're gonna do the same thing over here Give it a little out of this. Yes, sir shoot That was my last bit of uh, this is my last bit of You got to get some supplies or to cap kits for the uh other style pdms that you can see we work on most of the time 50 series and stuff like that the m-series I got to get those cap kits I definitely need to get some What do I need? I need everything solder. It's a good time to get it right at the end of the year I need more solder. I need more solder wick so Just try to go from the other side and see how much I can get out of this See if I can get anything out of here on this one Whoa, that's hot. I think it's something there You know, it's close to darn full saturation Okay, good enough Just touch up the solder a little bit You know, if I was just like a schmuck, I'd leave all this and not clean it But man, I'm not like this. This is hideous And obviously I might not even have I don't know. We might have to try something else I don't really have pretty much alcohol to get some Okay, because yeah, that's got to be cleaned up That is gross. It's just so much flux on there So much flux. This has been a long fun stream. So here's the deal Let's see if I have any way. That's it. That's it for the cap kit Put some stuff up That's solder reflow Yeah, don't worry about the saw. Thank you, Belmont. Keep dropping that. Don't worry about the solder fumes They're literally flux and every time I do that I breathe out I do have a fan that I normally use but I'm not going to use it while I'm down here. It's gonna then it'll just you'll just be like what's that noise Is it do you hear something? Is that or is something noise going on? Steve have something And so I don't really want to annoy you with all that This is wonderful. Let's see if we can get a little bit of cleaning materials here Let's go back and check See if coal's there. Oh, yeah, he's still sleeping This is something right. I don't really want to try experimental crap generally on PVM. I mean this is not gonna hurt it. I also don't want it to Spray everywhere, but these are some electric electronic cleaners. You're supposed to be able to clean sensitive electronics with them I'm not really Have to worry about it. They're from like automotive shops mostly One by CRC. There's one by uh wd-40 here And I don't tend to use them just because they cost so much most of the time All right, so let's just go with this. This is the CRC stuff. We'll see If it does anything down here, it doesn't really even work as good as probably Just good old-fashioned Alcohol really is the best on these things most of the time. It's just getting real weird You can dry it out a little bit Look how nasty that stuff is. Man, that's gross Oof, let's see what this stuff does This is the wd-40. It seems to work better Actually It's getting pretty clean right there actually Oh, I'm sorry. I'm off the screen a little bit here. Let me show you You can tell where I actually sprayed it. You can see How much cleaner it is right over in this area All right, let me see. Look at that. Gosh, some of this is just gummed up Sometimes you're gonna take like a little sort of pliers and It's gonna like scratch that stuff free. Don't don't try to scratch the board just Scratch Dirty stuff Flux Did pretty good And like I said, most of the time I just use the Isopropyl alcohol because it's the cheapest solution to do and It's it's pretty effective for 99% of the time I'll do that Actually now that I got all that done right there Let's find what I'm gonna finish This with is some IPA. There we go. Look how much cleaner that got, huh guys? That's pretty quick. It doesn't look crusty anymore. Oh, baby. Look at that. That's like A million times better looking, isn't it? I'm just using the IPA over here on these other Spots where I change these capacitors up here There's three of them in this area Yeah, 91 is about all I can find all the time anyway. It's okay. That's what I've got It's don't feel so bad if you can only find 91% Maybe you can order some online I can never remember to do that beach towel back on here. It's the place to do it I've done over here This zone over in this area I'm sure if this works, right? For Bob's sake, I didn't mean that my work would work. I just meant to repair. Hopefully We'll solve the issues that he has. I don't know It'll be interesting to find out and see Looking good. That's pretty much going to do it. It's all my IPA. I'll have to go to the store and get some That's pretty much way to finish things off right there. That's good Everything one good Come back and rub it all down and then I'm going to go set it under my high speed fan To dry it. That's what we're going to do. I'm going to go set this under my fan to dry it. There we go There we go. So look kind of great. I'm going to say the truth now But it's just an awesome amount of attendance today like There's a lot of people here And I want to say thank you all for coming and spending your time to hang out and you know Learn about whatever CRTs watched me work on one of these rare machines And uh, it's been fun. It's been a two and a half hour stream Which is a long stream for me, but I'm glad everybody's been here. It seems like it's done well A lot of great interaction from the audience. I appreciate you Belmont and everybody else has been here helping But that's where I'm going to end it today. I have to go get my kids from school And we're at a good stopping point where this board can go dry I can do some cleaning back in the inside of this and get things ready And actually what I can do then is I can set everything back up and let it sit cold and then I'll come back in the next stream We'll test it cold and see if it powers back up because I know I didn't do anything to screw it up At least I don't think I did. I'll cue see it and stuff But you got to see the hard work you got to see some tricks on how to actually work on this CRT But if you want to learn more Please feel free to check out the link in the description of this video or just subscribe to the channel And be ready for the next live show, which is normally scheduled for thursday, but I may have to move it Uh, I may actually do a live stream tomorrow to try to finish up this pvm instead of just waiting till thursday anybody Sorry if you came in late you can go back to the beginning of the stream and check out this awesome Stream on the 1405. I appreciate you all again. Have a great rest of your week And I'll see you in the next venture into the bunker And I tell you I gotta quit putting my mouse Places so I could