 So here, new project. Pretty much the same street as we're always in, isn't it? Yep. These are our bricks, Carlton headers. Good brick then. 73mm, but it's an older house. We've been here twice before. We've done the lintel on the back and then we did the steels. This one was all covered up for the steels. So this is our job today. Well, it's a start today. It's a small utility. A customer who dug this one out for us made a lovely job of it, dropped the floor down. That's a gas main. So I'm going to cut the concrete either side of that, so it's not in the concrete. That's the supply to the shed. We're going to cut the DPC in, the vertical DPC. Get loaded out. Same again, vertical DPC. We've got a vent to pipe through there. So we're going to take this vent off, put it in this wall, put a pipe through under the floor. We went to Berry yesterday and picked up the jab light for the floor and the cavity installation for the walls. Everything else is getting delivered today. Soon hopeful. Yeah, pretty standard really. No door in it, just a window. So it's going to be blockwork first showing up. Yeah, that's pretty much it. So now we can just get it set out, marked out, get it loaded and then see where we're off from there. Oh yeah, there's the ties. Do you want to give us a tie at all? Just pick these up from screwfix. There's those. Pretty wide but we're here. You can bend them. Bang on them. They're a lot easier to screw in than the blue birds as well. Yeah, I can do everything which means anything. Right, so let's get cracking. Let's just place the one thing first. Excuse us our measurements. One, two more. Two more. Yeah, we've got a tape out. Pretty close though. That big isn't it though, let's try to take it off. Let's take one more check it. What is it, brick from the get-go? Brick straight off. Brick straight off. Yeah. So our measurements. Yeah, one, one, five, zero. One, one, five, zero. One, one, five, zero. One, one, five, zero. Yeah, one, one, five, zero which works. One, two, three, four, five, brick. Now we're going to get our wits and then we're going to work out the diagonals. One, point, one, five, zero. Squared. It's thirteen. One, three, two, three, five. On the pelts on my right. Yeah. Go down low. Two, six, that's your turn. So bring your scoops of bricks up. Please. So we haven't got an exact measurement for the wits, so we're going to go for the brick size and then the brick on the half. So we're going to trace the bond out. We've got 2.6 to play with because you want the brick bond to work out. So I've pointed it, that was right. Yeah. Mate, it's probably not right. I don't know how I've got that one. It's such a bad thing. Oh, I've got a big brother. So does that break to a half as well then as well? Let's see what that measures. Six, twenty, two, six, twenty, is that right? Yeah. So two, twenty, six, two, zero. Squared. Squared. The six, point, eight, six, blah, blah, blah. Plus, so you add that to your side number. What's that big number there? A major one here. One, three, two, two, five. So that's eight point one, eight, six, nine. So now to get your diagonal, square root it. That's two point eight. Two meters, eight hundred and sixty-one. Two meters, eight hundred and sixty-one. That's the only thing from school that I still use. Yeah. A squared plus B squared is C squared. That's right. Two eight, six, one. Right, let me write down. Two eight, six, one. Two, six, twenty. Mm-hmm. Right corner. Welcome to all foundations set up very easy. There you go. Set out. Projection 1150 with two, six, twenty. And then we've got the diagonal thing. So now we can get loaded out. Right, that's us, Brutam now. We're all loaded. That's this end loaded plus what's going on in the scaffold because we're going to have a little half pike lean to roof at either end. Yeah, pretty much it. Five course of facebrick off the concrete. I'll just put a picture of the dig. Nice dig. And I think there must be good 450 concrete in there. Maybe even more. There's a cube. Over a cube gone in. So that's all set. And forwards have been and brought all the rest of the gear so we can just crack on today. We'll get it up to damp, ready for slab, and then look what we just carry on with this wall. Take this wall up, take the facebrick up on this end. Just give it a bit of a head start. And then we mix in our own concrete for the slab and then so we can do that tomorrow. Maybe Saturday. See what the weather's like. And then once we've slabbed it, we can carry on. And then we'll probably leave here. We'll probably leave a bit of a V out in the brickwork here because this is where the window's going. About here. So we need access. Obviously, because we're not doing the brick down until the roof's on. I think customers doing that themselves. We'll go and get a brew anyway. Right, we've got our outside face mark. We're going to come in a hundred and a bit. And we're going to do this put our cuttings on the western DPC that goes slots in. Which, we don't see the point of putting it in but a lot of people seem to be reading it. So we'll put them in both sides. So we're going to turn that to the cutting. There's probably other marks on as well for the internal wall as well. After you. Do you mean after me? I'm still mixing. I thought you were taking the motor. I thought you were taking it? No, I'm filming you. Carry on. Oh, you're a real hero. Yeah, thank you. I can't do it, you have to do it for me. Come on. Oh, touch camp. Hey, do you like the blue paparazzi here, you know? Whoa, whoa. Where do you want it? On there please. It's not the best one but it's magic. It's magic. It's magic. It's magic. All right, ready to rock and roll. Here's our mark back in the dust. Let's go DPC cutting as high as I can reach. Now, DPC's here. As you can see. When we get to the vents, it goes up and over. So I'm pretty sure floor level's going to be up this area. So we're going to put our DPC at this height. So it's five to damp. Which should be five block. Sorry, two courses of block, hopefully. And she's known it works out with Imperial Bridge. She says. Remember last time we needed a 12, 30, 10mm? Yeah, we had a bigger post. But in the street, we say it's supposed to use eight. So now you can actually level off here. Be careful picking it up though because you might get it too quick. Be very careful with it. It's super busy. Yeah. That van is halfway down that street. What is? That van you can hear. Oh. Yeah. Don't take them both out. The bricks are so dry. It joins them almost every course. We're going to start running in a bit. The pipe. Rock hard. The bricks are so dry. It joins them almost. That's it. All sorted. That's damp course level. Floor level. Floor level-ish. We'll see when we push through to find where the level is. And then we're going to be concreting this ourselves with the mixer. So that's it. I've quickly reached now. And we're going to get it leveled. Get up to DPC today. Because I've got to go off and get my COVID injection this afternoon. I never thought I'd be glad to be having an injection but I am today. So we have to leave it up there. Right. Alex is just getting half a mix in. Down there. I'm going to concre on the block work now. We'll start running that round. There's going to be two tight courses. And then Alex is going to get this route running. And then if anything left over I'm just going to run a corner out here. Just to use them all up. Because it's all ready for profiles now. So that's it for now. Let's go back to 10 blocks. Right. 25 to 3. You've got it the right way up. Yeah. That's going out tonight that. Yeah Alex is all tidied up. We're going to use the mixer now today. So we're going to cover up now. Just before you do that. Can I cover the sander with the board? Yeah. Yeah. Because we can always use that plastic that's by the bricks for the blocks. It's a bunch of the bricks. It's alright. Oh there's a bunch of panels. Use one of them. Alright. Anyway. Back to it. Quick update. I've just had to nip off to screw fix to pick up a couple of the vents. I'm not putting the periscopes in. We're just going to put the vents in there. What I've done is I'm going to pipe from under the vent. Obviously to vent the floor I'm just going to put a 4-inch piping straight across. And that's going to vent into the cavity. And then we're going to put the air brick in the top course. Same here. I just need to cut that out before we go. And then so obviously that's going to be... We're putting two pipes in. There's only one. We're only covering one vent. So we're putting two vents in to make sure it's well ventilated. And then plastic vents on the top. Then these vents are going to vent all this cavity. Because this is all going to be open. Installation starts there. So you've got all this open. Then you've got two pipes. So that's plenty. We've cut round the gas pipe. So we're not sat on it. So that's all clear. Same there. So the plan now is get the rest of these face brick on. And maybe put a bit of a corner up to use the motor up. And fully fill the holes up. Ready to put the damp on. But tomorrow is backfill to here. Hardcore. And then it's installation 125. Then it's a hundred mil slab. And we're going to mix the concrete ourselves. So this armoured cable is going to be all. It's going to be under the floor. So it comes out behind the blocks. Under there. And then put this back up there. Let's get it finished and get packed up. So it's a broken brick. I can stay in here. I was going to fill it down to clean the cavity. I don't want to put it over yet.