 So I'm going to take you with me. We're just going to put some fixer flat in it because it's got a real slow leak. So in package, I will get the main package camera's going with on Monday. See this Monday. But I can tell you it's batteries, but for what? You'll have to wait till Monday. All right, let's get on to the other projects. We're going to be doing a couple projects today. So let me get this camera wiped off, change the battery, we'll get started on something. Hang tight. Stuff we're going to be using, we're not going to be using that. I just got, I picked that up because I had to get some welding wire for this project from Monkey, which you'll see. We're going to use these four and these four little feets for the air compressor, which is doing good. But here you can put, sometimes you can hear, but it'll give it a little to stand on. Get my drill out, I got a drill couple holes so I can put these in. I'm going to grind these off flat, you know, here. So they don't have that curve out to them. So they'll screw on flat. The bolts we're going to be using with these stainless steel washers have to use a lock washer on it. See, and they'll grip right in. So these should be okay. And so let me get you set up on a stand. The first thing we'll do is we'll go ahead, we're going to grind these off smooth, flat, you know. And then we'll put these up in here and we'll drill a couple holes in it with my phone. So I got the welding, I got some new tips. He gave me these tips. I think they're 35,000, so I'm not sure. There's my tip. So I want to try these tips and see if they work. I didn't get a nozzle. I think the nozzle will be fine right there, but nothing a file can't take care of. But anyway, just for what we're going to do with this, like I said, we'll get to this later. We're going to build monkey something. So let me get you on the stand and we'll get ready to go. There's my helmet. This is out. Now we're going to change our wheel, unscrew this. Use this one. It's an old wheel. It's something that, you know, when I don't have to get so aggressive, it's worn down, I think it's like 40 grit, but it's worn down so it's not so aggressive. And I just, I just hand tighten them like that. You can use a wrench, but I found when I do, that causes more strain on these. And then once one of these breaks, you try to get that off there. It's a pain in the ass. So I just tighten them by hand. And now you should use the tool, get your tool. Well, I've got the tool right here, but like I said, I've never had one come loose on me. Never had one fly apart, you know, from here from being too loose or anything. So that'll give me the length I need. So I'll use this one as a temp compressor. Okay. Now as you can see, I've got that propped up on that little thing we had it propped up on yesterday where it's perfectly level. Now, as you can see, hopefully perfect size, perfect height. So let's go ahead. If I had something on the end of this, 15 millimeter headed bolt. Not sure what the threads are, but the other side, I'm gonna put the other side on. And this little girl will be done. Hands to stop in. Cause he's wanting to bring the tent and set it up and show it to me and everything. It's an old one. I forget how old he said it was, 80s maybe. I don't know. I'm gonna get the other side on. This will be done. He's not getting my blow gun, but I'll give him their hoods if he wants it. And monkey's project. First, we gotta take the, the welding wire. That's two pound, 30 thousands roll. And the grinding wheel was $29 and something. And I'll show you how to put that on there and run it up through. It's real easy. And then we'll plug that in. We'll check our helmet out, make sure it's still working. Sometimes it kind of acts a little goofy. That's okay. And then we'll, so let me get that other side on and I'll be back with you. All right guys. It's just one, it's just 110. Just a little Chicago electric mid-wagger. It's wire feet. A lot of issues with these as well as I am too. These things, see how they're, they're plastic. And they kind of move, I don't know if you can see that moving now. It moves apart. This is your drive wheel. This is what pushes the wire through and out to the stinger. Okay. Now if you keep this tight so it doesn't unravel, it doesn't push it through. So I've seen guys putting seat clamps and stuff on here, which is probably what I'm gonna do. And this is not an isolated problem. I guess people are buying them brand new and they're having that issue. And you would think by now, Chicago electric, why they're not? Or why they haven't? I don't know. I mean, look, I understand it is a cheap welder, but geez, you know, it should do what it's supposed to do. I've said that a million times. Okay, so this is probably what comes with it. So, or what came with it. I'm using Radner. I like their products. I used to do a lot when I was working at the trailer for park trailers. And I guess that monkey's off the day. She's going laundry, cleaning the house, getting about that time. Okay, once the CV-19 gets under control, hopefully we'll, I'll get to take her out and do something. Okay, so I'm gonna put you on what the fuck was that? Do you hear that? Oh, thunder guys. Must have hit something, lightning. Okay, so let's get this put on here. I'm gonna put you on the stand so you can see a little better. Okay, try to get you over here. I know the lighting sucks, but we'll get into that sometime. Right now I got other things, other projects. So I got you on the stand here. Whoops. Okay, well, I was gonna bring you in it anyway. What I'm trying to show you is how to feed this through and it's gonna be kind of hard to do. I'm gonna get you up in there maybe. I'll show you how this, this just, you know, goes on to the spool like that. So I'm gonna open this up and I'll show you how to start feeding this through. But first, also you wanna keep the wires straight as you can keep your stringer. Straight as you can keep it. That'll help in not bunching up so bad. So this is just gonna pull out. You wanna get that pulled out. It's like that. Now you have fishing wire in case you wanna, not that kind of fishing, you're gonna have to know how to dug out. In case you gotta run wires down through a hole and it's good for that. Okay, so this, this is where that little tip is gonna screw on. Won't screw on to this. But first, let's get this started up through here. Whoops, monkey behind me. Messing around there. This is, that's the way it comes. This is flux cord. So what we're gonna wanna do, someone put this on here first over here, tension on it. But if you put any kind of tension on it, it won't feed through. Okay, so now we're gonna have to cut this off. Let me grab my cutter. Pull this out through here. Out that little hole right there. And we're gonna cut this off straight. You want it as straight as possible because if you get any kind of interference, and this is trying to push it, a lot of times if you melt the tip or weld the wire to the tip, this is keep wanting to push through and it just keeps pulling the wire off and you get what you call bird's nest. Or what we call bird's nest, okay? And I'll have to get you close up shot to show you something else here in just a second. Now you wanna get this started. See how I'll show you here in a second, a better view of it. But you see that wire, see it's going, there's little, there's two sides of this. There's a 30 thousands and a 35 thousands, okay? So what you wanna do is you wanna open this up, relieve the pressure off of it. Let's pull that up and pull that out. There's a little groove right here. And you're gonna wanna make sure that once you get this through that hole, gotta get it through this little hole here. You wanna start that through, you know, go a little bit with it. You don't have to go far. I mean, you can feed it all the way through if you want. But what I usually do is let it, see like I said, there's a little groove right right there on that wheel, that's your drive wheel. Make sure that wire's in that groove. This one's just got a bearing. It seems to be okay, it's a little dirty. But like I said, they're having trouble with these things. And it's like they don't wanna fix it, but they'll take your money and then oh well, right? And I had this as tight as I could go with it. My hand's in the way, sorry. I had this tightened as tight as I could go and it's still slipping. Like I said, a lot of guys are putting clamps on here. Which is probably what I'm gonna do. First, I'm gonna tighten this down all the way. As tight as it'll go. Now I'm gonna plug this thing in. All right, let me back you out a little bit. I'm gonna plug it in, switch on, just like that. Here's the stinger. I'm just gonna pull the trigger until the wire comes out here. I'm gonna speed up a little bit. It's caught up on something. That should not have come out like that. All right, so I guess we'll go ahead and we'll put the tip back in it. I'm gonna try one of these new tips that the guy gave me. It's a 35,000, but you can, yes, it does fit. Good. Now we're gonna clip this off. Now we're gonna put our nozzle on. And that's about where you're gonna be welding that. Another thing I don't like about this, this thing, if you touch it like right now that it's on, if I had it grounded to something and I touched it, it'll wanna weld before you pull the trigger. So I don't know if they're doing, if they're having issues with that too or not, I don't know. But I'm gonna go ahead and I'm gonna take this back over, back over onto its little cart. And then we're gonna do a little bit of welding just like that. So let me get it over here and I'll get everything set up and I'll show you what we're gonna do for monkey. Okay, so we got these little flower hangers, I call them shepherd's hooks. We got two of them. What we're gonna do is we're gonna weld these together like that so she can hang. It's for her mom's dog that is buried out in our backyard. What we're gonna do is we're gonna weld these like this so she can hang a plaque on one side and a little plant on the other, a little flower or something. And I think she got these Dollar Tree or somewhere they were buck. But the first thing, I'm just gonna put like three tacks of weld. I'm gonna put one up here, one in the center and one down here where these things are gonna go. Like that. I could probably AB weld it, it might be fine but I want it to be strong enough for her, you know. So it doesn't come apart for her. But the first thing I gotta do is clean this paint off of here so we can maybe get a good weld to stick. So let me get this cleaned off. Again, I'm gonna bore you with it. I'm just gonna take the paint off over on the wire brush, the wire wheel and three spots. Then we'll get to welding. Well, I may have to do a fourth spot to where I can, I'm gonna put it in the vise so I'll probably have to, I might be able to ground to the vise but we'll just see. What it'll probably do is just go ahead and clean off another spot down here because I'm gonna repaint these anyway. They're still gonna be the color black but they're not, you know, it's gonna have welds on it and they're not gonna be pretty. So yeah, I'll just maybe, you know, right here or something. I'll put my ground clamp on, my ground cable. So, all right, let me get this paint cleaned off here and then we'll move on. Okay, I got the fan running behind me, sorry. I cleaned off that down there so I've got the clamp on there. Hopefully we can get, you know, some spark action out of that and I'm gonna go ahead and get the stinger out here. Gotta get my welding helmet on, so. Well, let's speed down some. Here we go, it goes. All right, here we go. See, I'm not hitting the button. Now I am. Let me grab my welding gloves, hang on. Okay, got my welding gloves. All right, now, let's see if we can't tack these together a little bit more. I'm off to the side, ground off. I'm gonna go ahead and tack it on both sides. We move down and repeat. I'm gonna squeeze these together by scripts. Trying to stow out of your guys' way here. Let's do this one, and then the other side. Looking too bad. All right, let's go ahead and get the top and then we'll spin it around and do the other side. It'll stay together a little better anyway. So they're somewhat straight. We'll get these guys on here. Awesome machines. A little bit off, but I can straighten. Yeah, nothing beats gas, you know what I mean? Let's see, it did kind of turn pretty close. These things aren't straight to begin with. As you guys probably saw, this doesn't have a temperature setting. It just has a minimum and maximum on it. It does have the only real setting that's got the speed setting on it. So I'm gonna grab my wire brush here. Not too bad. All right, let this cool down. Grab me a smoke. And once it gets cool, I'm gonna clean it off and shoot some paint on it. And then maybe we'll go out and put some fix-a-flat in the golf cart, because after you do that, you should ride it around, you know? So stick around for more fun. You guys remember the wire we took out of the welder? I just braided it together. I also ground a couple of points in this thing so she can sort of get on the ground a little easier for her. Shepherd's hook there, hanging, drying. I'm gonna put some fix-a-flat in there. I'll put you here and zoom in, because it won't take the whole can, it's just a little tire. Don't you love it? Great, still half a can there that can't be used. Jesus Christ. All right, I'm gonna bring it over here, shoot some air in it. And then we'll take it for a little ride. Come on, Professor, we just built. We just kicked on, so. Okay, let's go for a little ride, a little bit. I could probably figure it out, which I probably will put a big-ass plug in just a little tiny hole that that stuff should take care of, but who knows, right? This thing turned around here. Super break, you know? It's not a CD player. It's got an 0.5 millimeter rock. Can't get a break from it. Crap it in there for a minute. Okay, guys, so thanks for hanging with me. We got a couple things done. We got air compressor, we got it. It's done, like I said, if you don't want it, I'll just keep it. We got this thing, which is drying. It seemed to be feeding okay, so I had problems with it. I had problems with it, her dad had problems with it. I know when he said you can use it, he says it doesn't wanna feed, right? He says you gotta keep it real loose. But it seemed to be feeding okay today, but that's not to say next time I go to use it, it's gonna work fine. The welder itself works okay for a little 110 mig welder. You know, a little wire feed. I still would love to have a Miller 212. That's what I had at work, and I love that thing, gas welder. I'd like to have a little tig. Browse will be complete. I can get by without them. I've done it all this time, but if I see him on sale, or if I see him yard sales or flea markets, yeah, if I can get it reasonable, I'll pick one up. Well, some of the, fix a flat in the golf cart. We'll see if it holds there, because I know Bruno and I, we take him outside. Well, I just got smokey cigarette monkey comes out with us. Well, he, he automatically, he'll go pee, and then he'll jump up in the golf cart and want him to take a ride. He gets upset if I can't take him for a ride because it's got a flat or something. So he likes to, I take him for a ride around a yard in the evenings, and he just loves it. So anyway guys, like I said, we got those are batteries. So Monday, do sides side by side comparisons on some stuff. And that should be interesting. So we still got that Google horn. We're gonna mess with it. I've got, we've got a lot of projects to do. I was going to do one, do another one today. I may do it later this evening, but I didn't want this one running too long. So I'm going to end it here. And if I get in something else, I'll get in something else. I still got a couple of tools that I got to pick up here and I get this swap up a little bit. So we can have some room to work on our next project. So again, guys, oh, update on that, on the twin cylinder, the opposed twin cylinder. I don't know. I was looking at the crank, it may be scored. If it's scored, I'm not going to put a couple hundred dollars in it. We'll just have to see. You know, I might find another motor for it. I might sell a whole thing. I might scrap it. I don't know. But I know I can get my money back just out of the carburetor on that thing. So just a quick update on that. So anyway, guys, Shabare the myth man legend. I'm gone for now. Thanks for watching. Weekend's almost here. One more day. We'll see you guys soon. Bye-bye and take care.