 Oh yeah, they're all cuts, 260 piece all the way up there, so while I was finishing that off I'm going in here, there's only cuts for my pillars over here So The reason we need that is, is to get this off, this remaining render so we can get the starter kit fixed to the brickwork And apart from that it's About nine o'clock I'll Five past nine, Sunday the 23rd of April So far so good, but it's not forecast very good So we're back on a Sunday shift because we've got another job booked in for tomorrow Like I say we're half a day behind because of all the messing about we did yesterday Still got a bit of messing about to do, but hence the that What we're gonna do is we're just gonna use our little hop ups and get the last two courses of this on from outside So not trestling outside That's our window those two bricks We've got a 600 window so that's block on block up to the Ties in every course ties across the every course and then that's the rest of the Lintel to go across and that's it then Jason and sort out what where he wants the wall plate after that. We're just getting everything everything to lintel height So I've got a list of cuts Just fell on the floor again So we've got a load of off cuts there we can probably use as well Here we are inside. I've just spent ten minutes chasing the bond working out the cuts Some of these cuts will be wrong because I've forgot about the window on the inside, but We'll come to that later. So here's our cut list. So I'm gonna be busy for next half an hour There's a I forgot Anyway, well, I'm sorting that out when I'm doing the cuts Let's finish this side off It's just a matter of plonking one more block on top of her, you know, we need to put the profile up I don't think And yeah That's it Still got a lot to do Oh, yeah, they're all cuts 260 piece all the way up there and oh, yeah There's no need for the commons on the inside. So it's just gonna be back to normal with a course in course It's 75 mil course. So that means we've got to put a 70 mile split all the way around She's a 10 65 mil splits So Alex is gonna finish that mix off and he's gonna get on with this side And I'm gonna get all the cuts done and then we can crack on then So catch you in a bit Right All the cuts are done. All the mess is made. Hopefully that's it now Alex got all these starters up So we're all set So this is course number. Is that a course number eight or nine? Oh nine, isn't it? Yeah, so that's that's our top course, which is lintel height So Alex just gonna get those last few in and then we can put lintel on from the inside We're not gonna bother with dressers just using hop ups with a cut for the sake of one course So I'll just finishing that off I'm going in here, there's only cuts for my pillars up here and We're all loaded out mostly ready to go starters are in blah blah blah Bonsor set out cuts are done Yeah, we're ready to go I can't say something I forget. Oh, yeah, when Alex is done there, he's gonna drop on this side this section here But yeah That's what we're up to I'm just gonna get all the damp course down Get some insulation cut it opened up ready four sheets per pack and Get cracked on so Plan is get this finished today. We'll see how we get on But we decide when up you can see that but there's no point putting trestles in here We went back over the trestles, but hopefully we'll manage without them We can reach to eight from from the floor So yeah, I'm gonna put you up somewhere seeking get a bit of time. That's going I don't feel much this morning all the cutting the dust So catch me a bit Yeah 25 to 7 on Sunday the 23rd of April. Is it St. George's Day today? anyway All done Fiddler ass pillar done with all all cuts and that is tie-wired to death It's got the starter ties in every course. It's got two tie-wires in every course As is this pillar. It's got the starters in every course It's got the two tie-wires in every course. So those two are solid. That's the wind that was added on extra You can see what we've done today on the outside And we've managed to do it without trestles. We've just done it off hop ups And then lads have been digging down out today and getting that prepped for the floor because the floor is going to carry on through There you have it one plant room boiler room utility room So there's the lintel not been bedded on yet and there's that lintel's got to be collected yet so Yeah, the whole internals been done today everything and A lot of cuts a lot of cuts as you see all cuts loads of cuts loads of cuts That's a bit bit unfortunate that but it's still still got a bond on it These cuts were done before we set the window out so that that cut should have been thinner and That cut should have been bigger and on the end so it should have been about there really But it's still got a good bond on it and we've covered the cavity up and there's the the monster cavity the 150 cavity Which we'll all be doing soon And there's the only extra work we had to put in to plank it out to give us some it's steady solid to work on that's great that There you go We've got a few other jobs to do now. We're knocking the porch down rebuilding that which is just single skin Got a door to knock out on a door to break up. So all the usual stuff for me and Alex There you go a bit of leftover insulation So So all in a good day's work You can see the From the beam filling go back doing this side. I'll hand you over to Alex in the van and he will do us an outro Right, and that is the end of the video We've got it done in the end if you enjoyed be sure to give a thumbs up and if you're new to the channel You want to see more be sure to hit subscribe because that's always a massive help to the channel and we greatly appreciate all the support we are Gonna try and reach 50,000 in the end of this year so Be sure to subscribe. This has been brickling with Stephen Alex and we'll see you in the next video