 That's our steel height there which is gauge and then we've got to get the laser I've set the laser up We spin it round plus the 37 that's two zero two five We need to write that down on the plate and good morning it's already a bright and sunny but we're here well I'm here dad has left me again so You know and I'm used to it at this point. We've done that many jobs where he's left He's getting the van service today, so he's a lot of this time Well, he's going to do that. I'm gonna get set up. So We've got the boards down so we can walk over the slab. There it is Very nice still a bit green. No, so that's why I put the boards down and And I'm gonna load out this side other sides already loaded did that yesterday so we can we can get another Two courses from here on the outside So Anyway Um, where was I yeah, I'll get the inside loaded out now and I think get those block pavers moved customers told us where they want them And yeah, just get basically just get set up as I can so I'll set you up while I do that and um I'll uh get back to you when dad gets here Right It's windy, but hopefully you're getting my voice because I've got this on Hey He's back. He's been busy Spent a good hour at least an hour probably over an hour Getting all the cuts done and my thick hoodie on my pants was he sweating to death But um, there's our leftover blocks And they're going to be The top course over the top of the steel and along the which will be Cut down to roughly 150. I'll show you what I'm going to be cut down to That's our steel height there, which is gauge and then we've got to get From that point up to that piece of red fascia and then Get that round Don't think There's anything in the back, but we'll have to find that one out and check with rubbish And actually probably will be one in the back On the back skin But we'll see If so, probably I haven't got enough two four six eight ten twelve fourteen Yeah, we'll see anyway We've might need a few more blocks, but we'll come to that we'll come to that next week when we're back So all the cuts are done Everything's done All the internal cuts up the They've had to be cut down on the internal skin to make them work gauge Because the back skin's been lifted We've chopped 35 mil off that so it levels everything back up for the tie wires All loaded out. So yeah, we're ready to get going now So it was big push today and then we're moving off this today On to um A new job for Vic Which will be on till we'll finish it and then we'll be back on this next week I think stills coming Monday. It's currently Thursday So time to get the chowl out. Well get the pants off and get the sun cream on and then um Get cracking So we'll put you somewhere out of the way and we'll get going We're in the afternoon now. I've had lunch Alex. He's just dropped the line. He's going to start running the pillar in So we need to get this pillar up. We need to get to padstone heights. I'm at padstone height now So the laser I've set the laser up. So we spin it round just catch it there. I hope you can catch it So that when it's shined on our mark up there That's our datum. So our laser is currently 37 millimeters below that mark so What I've done is put this somewhere. I've took this measurement Plus the 37 that's two zero two five Need to write that down That's our steel height. So that's bottom of padstone. So I need to get a few cuts from to get these padstone sorted It's a bit unfortunate because the padstone is going to sit on that half That's a bummer I'll sort something out We'll make it work So the padstone need cutting. We need a few cuts doing as well. And then we go around here Project that laser on to there There's our laser line. There's our 37 mill above And I'm gauged up. It's 230. So it's a nice big bed to the top top top lot So everything's working so so far We've got a load of 100 left over. So we're using that with all the 50 It's all 0.32. So just using it to make the 150 up. There's a 150 piece and just mix them up Yeah, that's 100 in there Yeah, you just shut up in the wall All right, I like them. So you put them in the wall all over the place. They look like they're making pretty pattern them Let's give them a try Right, um, yeah, I'll put you on Alex for a bit while I get over a source and get some cuts done Get covered in dust Well It's turned into a fluggish afternoon, but we're definitely making progress. The front is steel ready So that's the main thing done and We've got quite a bit of water left over so that's going to get some of that used up Yeah, so it was coming in a minute to pick that up to pick the van up the van up And so I'm just trying my best to tidy everything up because everything's got to go to this next job Which is frustrating, but Just got to do it So yeah, I'll throw you on to dad And I'll just keep trying to tidy up this chaos Six o'clock, but We've got three, three, we've got um Both sides Up to steel height so When we come when we do eventually come back here, we're ready to just plunge that steel and get this finished. Yeah Yeah But that is That's us done here for a few days so next time you see us in the next part of this will be uh Whenever we come back, so All right that last night just keep going You're going that way Rob. We're going this way just to get the wheels further back under this I promise you that it's heavy than it looks It does not look like much, but it's really thick steel. So that is That was a tough that's about Six seven mil box section that and it's six before On to it eight mil plates, which is three 40 deep because it's a six inch cavity. So the plate's deep And that's that is that is a lump But that's the steel that you needed for this roof the robbie so you can tell it's hot too because me forehead's out but There you go. That's been the start of the day get that steel up and we could have we could have got a gene this Yes, before everyone starts coming back to English, but that took us half an hour Bit by bit We're a bit traumatized after our last junior lift attempt as well. Yeah, three hours The last one we did we tried to get a gene list and couldn't get old of junior lift this one So a gene lift would have been helpful Anyway, we've we've got our technique that we do now. So we're good. We're good at getting these things up We're not in the business of rushing things up So saying that though now we've got to try and lift that up again and bed it on because And I think the task is We get that side leveled up to the steel and there's going to be a piece on top to go Was it was that going up to the piece just up to the um The red facial board. Yeah. Yeah So the so the piece is going level with that and then the back is being leveled with the back of the Box section. So this time we've got four blocks to go on yet So we may need we may need to do a fairwood run just to grab a few more blocks And then I think whenever it is we finish that we're going to pop on that drain Have you got the lubricant? Yes, I'm good. So that's the plan But now we're going to have a break because it is about 20 past nine and I've worked up a thirst So yeah, we'll get you set up properly after breaking and we'll get cracking Right kind of go organize now I've got ready to do the cuts which we do happening shortly Can't put a sun cream on yet because I've put some cream on just getting it covered in dust. So that's got to wait till the cuts are done So we've got a full course put around the inside full course put around the outside and then A full course around the whole thing I've cut except with the steel as a course we're cutting up to the steel both sides And currently got the laser level set up And nice level positions to this As you can see the laser set to the underside of this facing board That's our height for our block work. We've got to come in come in under here like this See it's just just shining on the top of the facing board there So that's our datum So now we spin it around Just see it shining on the steel there and somehow we're going to try and see it over there So I might have to use the air It's not a receiver. It's like a target But it's very hard in this kind of sun But I'm not complaining about the sun I'll be cutting all in mate. Just stick them all there There's a lot of cuts. Yeah a lot of cuts. I think it's only 10 full block and the rest are cut Yeah I'm just saying we're getting the levels around now That's set now. That's the underside of the facing board. So we're going to need to mark it up here So we just need a pencil and we've got one And a tape measure please mate Where's the other one? So what we do here is see if we can find this laser Doing there somewhere. There's two. I can see the laser level there We've started spinning around a bit for that. So this one If I do that There you go 365 millimeters You see that on tape? 365 I'm going to go to the outside skin Yeah, 365 So Al 365 Right Al. Can you just spin that laser to that corner please? Not far not that far. That's it There we go You might just make it out of my hand there This facing board's lower than the other one. So we're going to have to get the multitool out here. That's where we're going to There's our laser line So obviously that needs cutting out of the facing board with the multitool for that So you can get on there and that measurement is 140 so that cuts a 130 Cool That's a 130 for the internal And the external is 370. This is five below this end. So 370 minus 225 370 minus 225 10 25 and then two one two So that's what we left with so the cut needs to be one three five on the outside So what I cut's worked out. So I need a load of 130s and a load of one three fives And then yeah That's it Don't need to check this corner because I've measured that So I'm going to get down there and get cutting And Alex is going to load out and get a mix on Trying to mix on down in this corner out of the sun If you want these blocks out of the way if we can get a mix down in there in the corner away from the sunshine Here we have it catching a bit man in the cool bag. Hey He's left me phoning the van in the cool bag He did hear that right. It's in the cool bag keeps overheating. So I've put it in the cool bag to cool it down so Talking of cooling down. We're now in the we're in the shade And Alex finished that end off all done So what we've got left to do is come across the steel at the front and put these coupling at the back All the cut through here done. I was like that. I've never seen cutting for two hours Felt like two hours So, um, while that's getting the mix in I'm going to drop all this scaffold and get it all transferred up to here And then we can get this back on Tied up whatever we can't. What don't we stay? So yeah, while Alex gets the mix on I'm going to get it all this dropped and moved across it here And then it's just about a dozen pieces to go in then and that's us leveled up and done Um, yeah, that's it And we're out here. Well, we're back here tomorrow for a couple of hours in the morning to get the gully in the gully is going to stick out Gully's going back in and it's going to stick out into that corner and then the echo can be channeled into the gully and then we're connecting back to the original gully which is Down there Because if you've watched this little series, you'll remember that that gully was higher than that gully And it didn't travel as far that sort of went across the corner here Whereas it's going further now So if we put the gully in with as little fall as possible then the actual echo can go in I know I keep saying echo but that's where it's at I've watched the video of the company and they say it's called echo I know everyone's called it echo Justin Brickett called it echo but anyway You can put your echo drains in echo drains in level Which is good Because as they say you can't stack water It'll always bounce way away So even if they put a 10 mil fall on it, it'll get away But that's anyway we can get The downspout in from that end Because we're fixed with that point Without taking the fence out, taking the gully out and digging back down to the The soil pipe over there And there's no chamber on it either, so So that's it I've got a couple of, well three tubs of 10 mil limestone for the bit the Pipe bedding Pete gravel whatever you want to call it So looking back for that tomorrow There's a bit of a lump here That lump's going to be dragged down and backfilled over the top I know people say we should have done the drains first But we would have been stamping all over the drains So it's not a big deal to do that last And then we've got all our levels and everything as well So yeah we've got a little bit of points to do here We ran out of water before dinner And there you go, there's the padstones Lovely job And get rid of a load of stuff today If not, we'll take it tomorrow and we're doing that The back to time lapse, let's get this scaffold shifted There we have it What time are we on our path three? It's been a slow day today though I was rafing on and off at dinner time It's got that hot Well as you can see we're getting the shade in the afternoon So we're done Alex did that side this morning After the Robbie's had helped us get the steel up That's a solid lump, that is heavy, heavy But that's specified by a structural engineer We don't just put anything in anymore We make sure we've got an engineers report If we've not got a nice finish on it though So this is staying up tonight We're going to take this tomorrow We're just going to put everything else that we can in the van Start moving stuff And then tomorrow we've got that drain to do And a good tidy up and a good clean up So as usual a little time lapse of the cleanup And then we'll see you in the morning Morning, it is like Probably near 10 o'clock We've had a bit of a late start Because we've not got much to do today And we've had a fry up Friday And since we've got here we've been sorting the van out Getting all the last of the stuff put in So now we can just get focused on the work Mixer's got the happy stones in for a little last rinse down And today is get this draining So I think it's straightforward as dad has been saying Just get it so it goes to here with a good fall And the rubbish will put the echo drain in As that's been said a thousand times I give this a quick scrape back yesterday So hopefully that'll be at level And as dad with our big pack out There's a good look at the extension Now that it's all emptied out I always say it always looks small when all the stuff's in But once all the stuff comes out Then you see how big it is And there's a nice heavy steel So yeah enough waffling on That's our task Once oh and dad is going to the front Sorry there's a bit of a bit of rendering to come off again So he's just going to point that up now While the sun's on this side But yeah that's the task Let's hope we can get this done nice and quick Hopefully we'll be able to drop all the trusses off at another job later So it saves us a bit of time next time I'll get you set up somewhere I'm keeping the blower It's my air conditioner But here we go Gully's in Yeah yeah we'll do yeah So where was I? Yeah gully's in Stoned up and backfilled There's only a small four on it Because as you can see it's quite high So I think instead of an echo We're going to see if the robbies can Reroute all the water to go to that corner Which they should be able to do It's nice and it's just a square to redirect it Just saves me Instead of dropping one there Just bringing it here Just so the echo's not sticking out of the ground We'll see what they say They don't know what to do But that's that part done So if you give me a hot second I'll get you an outro There we have it So that is this job done Lovely extension I cannot tell if you can see Because I cannot see anything The sun's right in my eyes So there we go One lovely nice straightforward extension Once that dig from hell was done The only dig was digging the steel With the only challenging parts But other than that This has been a nice one And a nice drainage So I'll keep saying so again But that is another one ticked off So thank you all so much for watching If you enjoyed be sure to give us a like And if you're new to the channel You want to see more be sure to hit subscribe And tap on that bell That way you're always notified when we upload That's always a massive help And we greatly appreciate the support Let's bring you in with the force This has been Brickley This is Steve and Alex With one nice former conservatory now extension And we'll see you in the next video