 one Shaber 1000 here today we're going to continue work on this 1963 18 horsepower fast wind now we're not just going to continue hopefully we'll get we'll finish it up so stick around let's get these bolts out of here we're gonna get started on this thing okay guys so I've been periodically coming out here and spraying these bolts down I don't think I'm gonna have an issue getting these out of here because they broke off up here so the head was stuck onto these bolts so I'm thinking that's why they broke off up here not down here usually if they're stuck in here they'll break here so I'm gonna try to do first you know we may have to heat these up I can't heat this up because it's aluminum but I'm just gonna try get old pair of ice grips first and see what happens now there's several several different hundreds of different ways you can get get out broken bolts but let's know what this video is about if you guys want to see me make a video like that then I will but right now when this this video is just about getting these getting this head put back on here these aren't the best vice grips in the world but that one's that one will come out okay see about this one oh yeah that one's definitely gonna come out that's just above finger-tight so let's get this one loose great all right let me get something else all right so I'm gonna try tie tie try to tap on me on this yeah what it does is stretch in threads a little bit and break some of that loose there we go all right so I'm gonna go ahead it's kind of boring just pulling these out so I'm gonna get these out we're gonna clean the surface off and we're gonna talk about that while I'm cleaning okay guys so what I'm gonna use I'm gonna scrape what I can off with this I think so I'm getting some down in there so I'm gonna have to I'm gonna put something inside there but this is what I'm gonna do I'm gonna scrape this off the best I can with this scraper then I'm gonna use a brass bristled wire brush you can use a brass wire wheel you're not use steel on these do not use a steel wire wheel on this this is aluminum now I'm telling you this because I have done it and I've never had an issue I just went real careful with it but still all it takes is one cough or sneeze or you know somebody walk by and accidentally bump the boat or whatever you're working on and you will cause big issues a little leak there so what I'm gonna do is just use the scraper and this you can also use sandpaper I use about 800 grit on it and use some WD-40 or penetrating some kind of penetrating oil and that'll clean up real good so that's what I'm gonna do and then I'll show you how I know the head was bought okay guys so this piece of glass all right now we're gonna take the old head we're gonna set it on here can you see that moving that should not do that and now let's check the new one nothing so it's not moving at all it's fine check this one and it's definitely worked I do know this thing was overheated at least once because the guy told me overheated it and had to get towed in so there's that this head looks pretty good it is off of 1963 I am a little concerned about some pitting here a little bit but these only get these head bolts only get torqued to 10 foot-pounds so if I go to 11 I might work even better these go to 11 all right guys so let me finish cleaning my surface up on the motor and we'll get to getting ready to put that on okay guys now I know the lighting sucks I got a light pointing over here you can see it right there I got a light on up here because I'm in the shade because I am in Florida I know it's October guys but I'm in Florida and it's 82 degrees right now so it would be hot out there in that Sun alright so make sure this is right it is right says don't use sealer so you shouldn't have to seal this so this is kind of what I may be concerned about right there but as Terrell says it's not the space shuttle right so I did get some new bolts this guy on eBay for three of these one of the 15 bucks I made an offer of 70 turned it down I made an offer of 10 he turned it down and raised the price from 15 to 18 I picked these up same damn bolt at my local hardware store for 65 cents each same bolt okay so yeah these are just shorter bolts and I did run these bolts all the way in and back out you can use a tap if you have one I do have a tap and ice that I didn't feel I needed it because they went in pretty decent now also what I've done what I done was I ran a little little tiny screwdriver up in these holes now these ones are blocked off and the ones on or that aren't blocked off except for two of them they go way in I don't know if they go into water jacked or not so I got it marked there's one there there's one here and one down at the bottom I am want to put a little bit of sealer on them just in case it goes into water jacket because if it goes I've rebuilt a bunch of these two stroke engines a bunch outboard engines this one I've never done I've never done one of these 18 horsepower fast ones a lot of loan is 63 so I'm not sure which ones if any go into water jacket so on those ones I am just going to put it a little bit of a little bit of this sealer on just a whoa look at that coming out just a tiny bit and that's way too much I'm just gonna put a tiny bit just about like that on there I'm gonna put this one in here and I'll get another one just a tiny bit it'll go around there it doesn't take a lot especially cars be careful when you do cars like even water pump bolts I know I'm for there's a couple that go into a water jacket and they'll leak if you don't seal them okay and I know there's one here now I don't know I don't know if it's a water jacket but I do know it's not a blind you know it's not a dead hole like this one up here it dead ends there you know so but that one you can get pushed clear through so I don't know if it's going into a water jacket or or what so all right let's show you guys something a lot of you guys may not know this on these these flat washers if you look real close there's kind of like a rounded oversight and a flat side a lot of guys don't know that it's unreal how many guys do not know that and it's I mean they're certified and you know they just they never know it it's something not many people teach I guess so let me wipe this off and get a lid on it so it doesn't dry up in this heat I think that happened because I actually had it sitting up here on the seat wasn't thinking because we're gonna be using this again up here okay so I'm just gonna put but all these boats in and I'm gonna run them up just kind of snug now these call for 10 foot pounds okay now there's two bottom ones I won't be able to get my get my torque wrench on but they say you can use a claw foot but I don't like using a claw foot on a torque wrench so I'll just tighten them the way I see you know the way I feel it you know it they've only got to be 10 so what I'm gonna do I'm gonna start at 5 go to 7 and a half and go to 10 and what I'm gonna do is I'm gonna start here or here whatever I'm gonna start here go to that one back and forth see what I'm saying back and forth okay and then I'll get them all show you that when I'll show you when I get to my final tightening at 10 foot pounds and that way you see what I'm talking about okay now also I was reading somebody was tightening theirs to 18 which seems like a lot to me because I rebuilt a 25 horse Johnson one time in and it was like 18 to 20 pounds but anyway that's I got this set on 10 pounds and I'm gonna do my final there it clicked there it clicked and there there there did I do this one there there there and this actually does fit down in here if I finagle it so there I want to jump over to here that one did I do this one that one that one and that one so there we go we're good to go I'm gonna make sure they're all tight again in sequence and then we'll go ahead and put or fix our gasket here for our thermostat okay now like I said already stuck this in make sure it fit okay but when I did a gasket got broke well I guess I broke it I guess you could say but I think they glued it on they shouldn't have known people's got to take this out and put a thermostat in it so we're gonna fix that right now say half of it so I'm just gonna do the half you know what I mean so because that's a pretty thick gasket I don't think you can just run just this gasket maker stuff on it as I think it would be too big too tight in there so this is all I'm gonna do if it leaks a little then I'll take it off and buy a new gasket but like I said this is not gonna hold be holding like 15 pound of pressure you know what I mean this up here then I'm gonna put spark plugs in it we're gonna fire it up and what we're gonna do after you start these up after you run a couple heat cycles through them you know so I'm gonna start it up let it get warm then let it cool all the way down and I'm gonna check my torque and then once we get it out on the water and boat with it a couple times you know three four times I mean it's real simple it's right here there's no reason not to do it once we ran it a couple times I will go ahead and check them again a couple heat cycles is all it needs so let's put this back up on here something don't look right there it's got a why's that blocked all they come up through here and down into there just want to make sure it's not blocking it off okay so now I'm just gonna put these screws back in here I'll throw the plugs in that's pretty boring and I'll get some water underneath it we'll fire it up how many of you guys noticed I didn't put that on there yeah me too okay guys another little rant let's put that bottom spark plug in there can you see anything wrong with that now that it's cleaned up that's right it's stripped that hole is freaking stripped out look at that god damn it I guess I got to get a hold of these fuckers now well anyway guys that's how you change a head gasket or a head on a 1963 Evan Rood 18 horsepower fastwind unfortunately I can't start it for you so let me go get a hold of them I'm gonna send them some pictures boy here lately I just been getting screwed all the way around and people wonder why why do you do why do you do rants because I want other people to be aware of this so it don't happen to them so anyway guys thanks for watching she bear the myth the man a legend gone for now bye bye guys