 So the plan today is, get this all finished up to height, that's it, the face work is up, maybe put a tower up and then the trestles, but they're two planks wide so we can fit the tower in for the high bit. The news is on, we've been here a while, 8-2-4, it's been here just after half past seven, so got the boards set up, got the bricks loaded out, that's funny enough to finish now, up to the three courses, three in a bit. Just getting a mix in, I'm going to uncover and we'll crack on. So the plan today is, get this all finished up to height, get it to our little level right back and then we're going to have to move round with the scaffold, probably put it through the door so we can cut the cavity out with the saw and fix the starter pack for the pikes. No need for the cavity to be done down there because that's where the doors are, where the doors fit. Well I don't think that's the cavity he's doing there, but I have to see what this building inspector wants, I don't want to cut the cavity out where there's no wall. He's had some funny ideas on this job, so that's it, I'm going to get all covered and by that time that mix should be nearly ready and we can crack on. Excuse the wind, that's it, face work is up three above lintel and you can see it was left down for the lintels to go in. So we're going to, that was already started on the block, we're going to go for break now, just after half nine, didn't so bad. So we're going to get the block up which is a 20 up block, get this all level up, get the wall plate on, then we can move the trestles across, probably across and through the door so I can get up there safely to get this cavity cut out. So we're going to put two big gashes in the side of the house, because we've been asked to. I don't even agree with it, I don't really agree with that, but doing as we're told it's been specifically asked for on the phone by the building inspector. So we're going to have to break now. In a while we've had break, that's just once a bit of fettling. I'll just get in with the block work and as I say it's just more job on the very own, still a lot of cuts to do so this is our full block to here, obviously where that tie wire is, the bottom one. And then because of the way the height is it's 250, so we can't do a block and a split like a sliver cut to do, cut, reduce it into two equalish. So one's going to be 95 and the other one's going to be 135, so 95 from 135 on top for the lintel seating. Same here for this end, but I've also got 140 pieces to go across there to bring it back into courses, because the lintels are at a funny height. So those cuts to be done, these cuts to be done, those two cuts to be done and then we've got a split course on top here, which is just the block straight down the middle, which is lucky that's half as many cuts to do. And that'll bring us back into gauge and then we've got a course on the block before we see wall plates on top of that. And then once that's all done, we can drop this and we can move over and we can start doing the cutting out on the house, which will leave us the two pikes to do. And hopefully we'll get stuck into one this afternoon and get the bulk of it done, which will leave us one to do either tomorrow or Sunday. So we've also, customs got to go and get the wall plates, some cement Alex, couple of cement and probably three. And a starter pack to put up here, because the building inspector requested starter packs, doesn't like our screw size. The starter pack's going up there and there, there should be, two should be, you know, it's only about a metre up and then cavity out. And then to do something with this, we're probably going to end up using our tower, because it's a bit higher, because it's going to end up quite high this pike. So we're going to have the tower and the trestles here, we're going to have everything here. So eight, 14 planks, eight pieces of tower and four trestles. We're going to have to empty the van to take everything home again. You know, we're going to have to do a bit of a hybrid scaffold here. Maybe put a tower up and then the trestles, but they're two planks wide so we can fit the tower in for the hybrid. We'll manage, we always do. So, well Alex is doing this here. I'll go down there and get all these cuts done. Chuck has aged to get to use this, now I've used it a lot. Still on three bars after all the cuts have done. The chargers for the battery, which is on, the battery as well. So, we're fine. So I'm going to get over there and get these cuts done. Here's our cuts marked out. There's two odd size pieces for my front lintel, because it's not a normal size. We've got these 235s and a 95. That's going to be the bottom piece, then the top piece for underneath the lintels. We've already got a 95 down there that just needs trimming. Let's leave a 95 and leave a 135. And then we need eight of the black spit down in the middle. So that's two cuts. Gives us eight pieces. So it's only actually one, two, three, four cuts. And we end up with two, four, six, eight, ten, twelve, thirteen pieces. Just four passing at the top. So, so much quicker than cut one mark, one, cut one mark, one. Just get them set up, just run through them all. In fact, I'll put the timer on for this to see how long it takes and I'll film it properly. Two minutes, one second to do all those cuts and that. Lunch over, Alex is just getting the last bit of block away done. And that is, the bed's a mess, it makes spin the blocks round. Yeah. Yeah. So, and the wall plates are ready to go on. So as soon as that's on, we can strip this. And we can set it through the doorway. Two trestles outside, two trestles this side. And then we can get this cutting done. Or I'll get that cutting done while Alex has a tidy up. There's a few little bits to do, bit of pointing and fettling up them. So, let's get you up here for the wall plate. I suppose a little bit, yeah? Seventeen, three, five. We'll do the content creator. And then you've got to finish off with it. But there we go, the wall plate's on. So now we've got to make some holes to get these lintels in. But the big side of the extension is finished. So progress. That gives us a day and whatever we've got left today to get the lintels in and the pikes in. So fingers crossed. I forgot to mention, we've got to strip the scaffold now, haven't we? We've got to move it over four foot to set it through the door so I can get the cutstone safely with the machine. Yeah. And then we'll have to move it again to build it. Hello. I want to try and get the lintel in today. So, you get the lintel in and just get across the lintel on one side. And then hopefully... Just lean over. I'll hold your hand while you're... To bring the scaffold in tomorrow. Six pieces, not eight. Knock the level over. It's a little bit bigger than the scaffold out the way. Yeah. Pretty great room, this. Toilet. Utility. And then you've still got the access through the door end to end because it's built up to the boundary. Anyway, that's up now. I hope it's going to be high enough. I might just have to go on the hop and take the top bit. And I've got to cut the whole pocket out for the lintel. So I'm going to have to go 360 wide for three courses and then take the 150 cavity up from there, which Dave, the customer, isn't very happy about. Instead of it just being a vertical lamp. Yeah, it has to be the cavity, which is two big six inch wide gashes up the wall. Yeah. It's not so bad because it's just like a pocket. So it's bonded underneath, it's bonded above. Whereas normally it goes from the DPC over it, doesn't it? And it's usually on the corners as well. So it weakens the structure. But we're going to have to start to pack either side. So we'll put them in every three and every block. Again, instead of twist, which is stronger. We have our opinions, but they're wrong today. You said it wants ones that can flex and move. I thought they'd put in tires and stop the thing moving to tie it in. It's like defeating the object, isn't it? Didn't you say slip ties? I mentioned slip ties, yeah. Which is for expansion joints and walls, so they can flex and during movement. Over seven meters long. What do we know? Right, I'm going to get the big saw up here and Alex is going to start on the outside, just snagging and tidying up, cleaning the boards down. So that's your cavity cut. And is this the... Nice job you got that done quick. You've got that done quick, nice job. That's the cavity chain. The cavity now just takes pocket out of the link, because you're going in. You don't need to go too close to it. That can get too close. But it's too big. I don't think you know where he's saying that. That's your cavity. There's your link. So it'll be the same on the other side as well. But today's focus is this. Try and get... Getting this little setup, and it may be while I'm cutting up, he'll get a few nuts and bricks running over the side, maybe. So, 20 past four. I can't describe how awkward this is. It's so fiddly. What lintle's in. It's busted into the wall. As you can see, it goes in there. The cavity chain that up stands. Reap vents, blah, blah, blah. There's no reap vents. Reap vents, yes. It's in Germany. Yeah. And we've got our other pack, didn't we? So we need two for the other pack. Yeah. There's all the serious clips. So we need a bit of insulation here to level it up, and then the tray over the top. And then it's straight block work from there. We're going to bring the towel from home, which is going to be wider than this. Probably about an extra plank wider. So we'll be able to reach that end, and we'll be able to get it higher. So we'll be able to get it up, probably up here. Two for the height and one like a handrail. Yeah, let's get it so we don't need all. No, just six. Six in all the planks. Yeah, that's it. It's just jointing that side. I've got the block work over. It's all tied in. And we've got cavity lintel. All things considered, all the fiddling about would be hard to do. That wasn't too bad. We've got all that part up. That side is finished. Wall plate's installed. Dad's got all the cavity clips out. Lintel's in and a bit built over. And we'll set up there now, more or less. So when we're back here, whether it's tomorrow or Sunday, depending on the weather, I'll get him loaded out. I'll do the snagging and get his cuts and all that. Then we'll do the same here. Well, it seems we... Well, I forgot to film an outro again. So from the office. Thank you very much for watching. If you enjoyed, be sure to give us a thumbs up. And if you're new to the channel and you want to see more, hit subscribe and tap on that bell. That way you'll always be a threat when we upload. It's always a massive help and we greatly appreciate the support. This has been the Queen of Stephen Alex. And we'll see you in the next one.