 what's up everybody welcome to the edge of tech let me know can you hear me can you see me all the things hopefully we're good and clear I got some camera angles let's see this box is big whoo a little light today we got the com grow t 300 not gonna lie this thing showed up I didn't even know it was coming so com grow hit basically shipped it out to me I didn't know I know a few of us I know I think Brian Vines was in the same boat all of a sudden they showed up and we got him so I'm super pumped for this where's my wife she is actually with Tristan our three-year-old actually he's a month away from being four so he's almost four and they are going to an Easter egg hunt we did one earlier in this earlier this morning and now they're going to another one that's like 15 or 20 minutes away that started actually started five minutes ago so they're probably already looking for eggs now South Africa loud and clear how you doing Simon Jose Kobe howling Shane what's up man expected German singing that would be hilarious Corey we're gonna start I promise architect architecture I'm guessing arc 3d texture got it yeah Kobe how you doing bring Tristan as well yeah so they are they're doing their thing they're gonna go do the Easter egg hunt then go do some shopping and stuff while I'm doing this so we're gonna rock and roll I this is the t 300 from Comgro I gotta say this box doesn't look huge right but it comes in at 45 pounds on the shipping label and I'm gonna there's like I don't even know five shipping labels on this so instead of coloring everything I just taped them because yeah Silver Bear 3d medic Vince how you guys doing Dr. Lester crystal how you doing I got my bubbly I'm gonna bury through the bubbly here and then I got a big thing of water so let me know in the chat what you're drinking welcome to a great Saturday afternoon it is officially cold wet and rainy here in Wisconsin I'm gonna get this thing cut open we're not gonna waste too much time because I want to see what this thing can do I have not watched any other footage like content of this printer at all I know other people have done live streams I know other people have done videos but I have not seen any of it so I'm going in this completely fresh all I know is it's a small version of the giant one they have come grown sovo merged together yes yes they did Dr. Pepper beer mmm both those sound good I love it yes they did and spoiler alert I have another solval printer in the other room over there that came in and we'll be probably unboxing tonight and getting it ready it releases in April and I can tell you it's called an SBO 8 that's what I can tell you right now so this is the T 300 and there'll be another printer coming so that'll be cool soval and comm go are rocking it right now yeah good good stuff also soval is however you want to do it right there they're merged soval is sponsoring my trip to the Rocky Mountain rep rep fest which is amazing so we're gonna probably have if I can make it work we'll have the SBO 8 on display at the Rocky Mountain rep rep fest two days it'll be technically two days after it releases I think it's gonna I think I can't remember when the release date is I know it's in April sometime but we'll have it there if I can make it work so that'd be cool it's going good light source engraving how you doing yeah let's get this bad boy unbox so I'm gonna flip it over I'm gonna do a little bit of this a little bit of that so you can see as you can see this thing is a monster so I might have to get like a even wider angle lens but let's see what's in the top of the box crystal will be there woohoo can't wait to see you cannot wait that'll be so much fun all right right away typical comm grow soval fashion here we have a lot of stuff packed in here we have a user manual that looks version one looks pretty good well a lot of pictures cool cool I like my pictures nice so very nice a leveling card so we're gonna put that to the side please clean the nozzle and do not heating do not heat it up before using that card that's interesting that we're gonna level not heated up looks like we have a box full of stuff let's see what's in here up down the box full of stuff we got a the spatula a side cutter some sort of board I'm not sure what that is yet we'll figure it out a bunch of parts power cable the good stuff you know wish you could port a teeth a T 300 you know I I need to look I need to see how much this is going for currently I know I think there's a I think there's a special going on right now on the soval website and so this baby thing of filament it looks like 200 grams PLA white I wish they would just send real real spools but you know that happens all right what do we got here this is our screen okay put that off to the side this must be attached there's the hot end but it's attached to you underneath spool holder thing looks huge doesn't it holy moly that's a beefy spool holder all right all right looks like cool I can say that these are machined metal going with some sort of brackets we'll find out shortly but these are these are machined metal that is awesome looking by the way I love how that looks what else we got nothing in this one nothing in that one I'm just throwing stuff all over holy mother so this looks like our our gantry here oh it is separate okay all right that is our gantry you can see it's probably see it's a little cold this was in my garage even though I have heat on it was only like 50 degrees in the garage so it's gonna have to warm up here a little bit there we go we're still doing good on audio and all the stuff let me know just making sure looks like we have the gantry here and I have I appear you know I've seen pictures of this and it appears that this gantry is not connected at the top sounds good thank you crystal so this is interesting really interesting it's got a wheel up here maybe that's a foot it must be a foot I don't know we're gonna find out I'm just gonna set it all over here any idea when the next one's coming out from bamboo no idea they do not tell me anything they pretty much just say here's a new model and there you go I have info on other other things like like soval SBO 8 I have one I can say I have one that's about all I can say about it and it releases in April I think I can say that too I just did but that's all I know so this is the base this is a beast holy thing is huge this must be a 300 yeah 300 by 300 there we go and this thing is a monster holy and it's all metal I don't even know that that explains the 45 pound ship weight of this holy that's huge all right let me get this out of the way toss it under there oh I don't know if you can see the size of this cable chain but it is it is huge as well holy moly it's got a house that ribbon ribbon cable all right so see if I can get you straight there that is the upright I'm sorry the base the uprights are over there we'll just kick back to here for now this thing is a beast another it is definitely someone I think it was Shane said another bed slinger yes yes it is gifted five edgitech memberships thank you so much Marshall S. Marshall and looks like YouTube already gifted them so Martin C. M. D. 3D Wayne Ken E. and Rodney congratulations on the memberships Marshall thank you so much for gifting five memberships we're gonna dive right into the instructions let me know if you guys have any questions I'm watching chat I got a full screen here and I will answer anything I can get to I believe there's linear rails and they're I'm guessing they're underneath this cover so there's a cover on here I need to look that I pretty sure I'll look it up so before testing this what bed slinger would someone go for I'm not sure what that means it all depends on your budget as well so interesting something I notice right away this thing kind of moves nicely and stuff unless I can twist this maybe it can be twisted I don't know something I noticed I don't know if it's gonna be an issue but the rear the wires the harness that comes off the bed right is right here and it has as you can see like a twist in it you see that so it's kind of interesting I kind of want it straight but maybe it'll be beneficial because it won't hit something behind it I'm not sure if that was intentional or not it's just something I I just look yeah linear rails on X and Y okay good best one at the moment no budget oh gosh stay tuned let me get this together and find out how this thing kind of performs since this is a calm grow video I want to see how the calm grow machine works but I can tell you there's a lot of really good machines out there and I cannot speak for this one yet because we just getting it out of the box yeah yeah this does have clipper I believe clipper yes extra cable looks rather shocking maybe there's a lot of stuff in here we got to put together still so just looking at this real quick it's 300 by 300 by 350 it'll move 300 millimeters a second I think it's squared or whatever I say whatever because to get to that speed is very uncommon like to actually hit the printing speed because there's not a there's not a lot of room here to get to their speed right let's see just looking here it does have it does have clipper it looks interesting cool cool cool cool so we got a package list and then when you're facing the linear guide kind of tells you about putting it together now I think yeah z-axis module so it doesn't stay like step one or anything it just it just goes from the guide of stuff that came in the box to the z-axis module right away so we're gonna just start following this this looks like when you're facing now when you're facing the linear guide slider if the x or the z-axis motor interfaces on the left side it's the left if it's on the right it's the right side so yeah I think it wants me to do it you know facing the machine essentially and it looks like we're gonna use m5 by 25 screws so we're gonna start getting all the screws out quick oh I bet you my t-handles are I might have to grab my t-handles I know where they are they're in the other room let's see so in this bag of stuff what's up my corner 3d 3d drunk it says t 300 not that it would be become fluid now and start to change here in there in the stream and become a killer okay not sure what you mean by that maybe I'm reading it weird the actual build size not the quoted one the actual build size says 300 300 by 300 or 350 I don't know what the actual is we'd have to we'll have to measure it I'm dumping everything out apparently just I'm just going for it dumping it all out here all right we got all these parts I don't need all these zip ties right now didn't need to dump that out terminator yeah it kind of reminds me there's an SD card in here you know your side cutter I don't need that yet spatula don't need that yet okay so what I do need oh looks like they gave me another hotend this is super interesting check this out we'll take it out of here real quick yeah maybe I'll have to build the terminator head on this right let's see if I can get that to zoom there we go so this is like another pot end or nozzle that they gave me in the box that's interesting super long tube here looks like it looks like it's gonna have a ceramic here on it because that's probably what that goes in there and your thermistor very interesting design there looks like two bolts hold it up in there if I had to guess again I haven't been into it yet but you know that's what I'm guessing very interesting looks oh yeah they give you some paste so it's definitely gonna be a ceramic ceramic heater they give you a little paste to put it on there if you want but yeah I gotta grab my T handles I love using T handle Allen wrenches and I'm about to order another set with ball ends on them because I love them too actually gotta throw it out there the Allen wrenches that came the tools that came with the machine here are it's awesome to see it love tools that come with the machine we have a nozzle unqlogger needle we also have a filament pusher so an unqlogger that way too so the needle would go up to unqlogger nozzle the filament pusher would go down through the extruder so it's nice that they give you those which is really cool also a couple screwdrivers a tweezer and I have to say the end of these if I can get it to focus again sorry there we go the end of these Allen wrenches are ball head ball end ball hex whatever you want to call these but they're ball I like that okay so I'm gonna get the 5 by 25 it's gonna be these it looks like and give me two seconds I'm gonna grab my T handles they are sitting right over here let me know if you have any questions in the chat oh boy we got to turn lights on in this room whoo good thing I know where they are it's dark okay I only knocked a couple things over you guys want to see something cool I showed this on Monday's hot makes Devon seen hot makes it's a live show that we are doing currently every two weeks and I got a something I showed on that but these are the E kind T handles that I love I'm gonna order some more those are amazing yes thank you Mauser those T handles are amazing check this out I just got to show this it's not perfect as you can see I left all the string on here and stuff but that is a benchy that is not a 14 minute benchy but it's a it is a benchy you haven't been checking out my social medias I've been showing that off lately that is that's a huge benchy it's a huge benchy all right let's get these let's get an these T handles are I love them 14 hour no much much more much more bigger bigger wrong size here we go so I love T handles like I said a bajillion times I'm gonna get some that have ball ends on them I'm gonna work on that and then find some I like so it says we need to face the machine and if you're facing the machine then it tells you I'm gonna kind of turn it like that for now it tells you oh you know what sweet I think we get to go down with the screws I love that yes love that we get to go down with the screws not up through the bottom and I really like that okay so it says face the machine right let me know in the chat you guys want this view do you want a top-down view or would you like like a side view I'll let you guys decide I'm gonna let you decide you know he could sit on this one I don't know how good it would go because I think I did two walls 5% adaptive cubic infill like yeah I'm surprised about the the bridging some of those bridging were like 163 millimeters or something like that it was long all three family father bottom-up view top-down oh no one can agree all right well here here's what I'll do let's see what this looks like kind of that's that's okay let's see what we can do here so it says let's see if you're facing it if the motor interface is on the left it's the left upright no way by motor interface they mean there's the plug right here so if I'm facing it and it's on mom the the right or the left you know I'm guessing it goes on the left because the cable is on the outside boom oh look at that that's actually solid holy moly there is no I can't explain how heavy-duty this machine feels currently we haven't even got it put together yet and it oh I'm gonna be able to use it oh yeah this is why I love the T handles and I get one I'm not gonna I'm not gonna tighten it all the way down but looks like for each one two three four one two three good okay so I could really do this any in any orientation I might turn this sideways so I can screw it in easier and faster but you guys will still be able to see it we'll do that so be down here right here there's four screws on each upright and then the cable that plugs them in is on the outside of the machine right here you can see that so little close for the t-handle but I'm okay with this because I can just I can just spin this in nice good fit solid yeah you can you can definitely 3d print t-handles for ones that come with kits and I have done that before I think I have a video on that actually somewhere out there about one of the tools that I like I love that you can do that and and in this case they're actually pretty decent Allen wrenches with ball ends so 3d printing a t-handle for them would actually be a good idea so I'm just getting these all down not tight yet and then I'll tighten them in a second here actually I might wait to tighten them until I get everything because it looks like we're gonna have to put our x gantry on here so I'll just get them to just about tight and then that's it it says 300 millimeters a second I cannot confirm or deny that they say they have like a 14 or 15 minute benchy we're gonna test that I'm really hoping the benchy is on the card and we can rock and roll a 14 or 15 minute benchy as soon as we get this put together so I'll drop all four in like that yeah and actually let's see if this I just want to make sure this camera is working boom anything we got anything no no I thought we had something no no come on oh this is gonna be very sad because this is a brand new battery alright let's try it there we go okay good so you can see what I'm doing here there are four to here two in the back and that's currently where I'm screwing it I can do that to yeah 300 millimeters a second yeah it went dark because the GoPro decided it wasn't gonna show through the HDMI for a second so this table camera I'm just using a GoPro and it works pretty good if I keep this in here there we go as you can see I'm not going all the way tight yet I will tighten it all up in a little bit but I do I really just want to make sure that the the excantory goes on okay before I before I do that T handles are a little wide but that's kind of why I want ball ends to so if I go in it a little bit of an angle it's not that big a deal sorry about the camera there for a second I'm actually really excited for this machine I think it's gonna be it's gonna be pretty dang cool so we got all four in there you can see that this is clearly gonna plug in like that when we get to that point I just did so the next the next is the x-axis it looks like we're going to install it so the x-axis is indicated on the platform I hope these are at the same height you know when installing hold the x-axis to avoid damage secure it with four m4 by 16 a total of eight screws all right cool so I think what I'll do know what I'll do here for this one let's see if I can let's see if this is a better a better view it's kind of a better view right because we're gonna install it right here there we go I like to move it move it I'm really hoping that this is a really good printer again have not watched anybody's material on this like zero and I'm really hoping that it's a really good printer because I have a friend that wants to get into 3d printing and I told him if this is a good printer I'd give it to him actually it's for him and his daughter there we go so we've got the screws we got we got the the t-handle it's up here t-handle gotta love it here is our x-axis and it looks like I'm backwards it screws in from behind so what I might have to do is turn this thing around that way I can screw it in that's what I'm gonna do so if you're building this at home it screws in from behind not front does they have two z-motors for z-tilt yes I know that it does have two z-motors and I'm hoping it does z-tilt tour what's up can't wait to see you out you're coming to remerf man that's awesome I cannot wait to see you there tour let's see so you guys can still see here I'll make that a little better so this is where we're gonna be screwing stuff in we're gonna hold our our gantry I'm gonna move it to the center here we're gonna hold our gantry and it's gonna kind of sit on there's like little lips I'm gonna hold it and I'm just gonna get a couple of these started so I don't have to keep holding it so you can kind of see that from behind now there is a shift it does look like I can shift this whoa side to side Tim is flying you out awesome that is awesome man I'm super pumped I cannot remember if I've actually met you in person yet I don't I don't think so though I can't remember so what's interesting about this just a heads up is it appears that you will be able to shift this a little bit so I'm hoping yeah it definitely will shift see this I'm gonna put these in loose to then I'm gonna screw the bottoms in tight and then we'll screw our gantry in because I'm wondering if I can get it in there straight we just need to make sure it's straight not even Tim and I worked with him for seven years what I did not know that watch so was live printing liked it nice nice anyone else in the chat going to the Rocky Mountain rep rep festival I know Crystal is and a tour says he is now not going tight on these just so you'll see that no as Joel would say no Ogadouga Joel will be there there's gonna be a bunch of people I think Stefan is coming Akuma mods Matt Ben it's boy in space is gonna be there it's just gonna be a ton of people Sunday there's a fun panel going on and I get to moderate it so that'll be a lot of fun and then also if you are going you'll hear my voice a lot because I am the emcee I am the master of ceremonies they're giving me the microphone all weekend and I'm gonna have a little fun with all the announcements and all the fun stuff nice Shane you're coming to Shane's gonna be there that's awesome Jake from State Farm what's up long time no see all right I'm gonna work on tightening the uprights now because we have our ex gantry at least up and attached this is this is a beefy beefy printer it's all metal so far my video it links to a K1 max what I better check that out real quick that's not cool thank you David I don't know why but I'll check it coming from California nice come find me say hi everybody if you're coming to the Rocky Mountain rep rep festival come say hi I don't bite too hard but introduce yourself like hey I'm this person because I will have no idea what y'all look like and real quick let's check the description oh I get my keyboard flying in on Thursday hey me too me too just popping into YouTube real quick here Amazon link to the K1 in the description that sounds silly who does that right probably me that's that's who did it working on it now working on it now I definitely I mean not definitely I definitely put the wrong link in there then right had to have almost there we're just gonna fix this real quick here come row T 300 I'm just gonna put the Amazon link back in there if I find it and then I'll find that I gotta get their website one two and put it in here because I believe there's a discount maybe on their website that's funny it's really funny I can't believe I left out there okay T 300 all right check it now we should be good now should be good let me go back to here I'll go back to the chat boom fixed should be fixed all right flying in on Thursday me too I'll be there Thursday through Monday I'll find out Monday one day yes you need to come to the rep rep festival Jake do it I need to meet you and your khakis irony looks great okay let's see what they want me to do here so right now I'm gonna look at this real quick it says secure them it does not say anything about like leveling them or any of that stuff that's interesting so it just says secure it it doesn't really say anything about making sure like because I can I can move this here get this over here a little bit watch you know maybe I just need to pull it all the way out that's what I'm gonna do I think it doesn't say what to do so for me if I'm brand new user I would just screw it in and make it tight I mean that's I think what most people would do I kind of would like to see an instruction on where to do it but I'm gonna pull it out to the outside hopefully that's where it wants to sit the right way to do it probably would be to run it up and down a couple times let it settle itself in and then tighten it in maybe we'll do that when I'm tuning it but for now I'm going kind of in a star pattern ish tightening these in just making sure they're tight and on this side I'm gonna like pull it because it's a little bit not so I'm gonna pull it out let's start here what does this show everybody's talking about I don't know I heard it's gonna be just kind of okay the announcer they chose is not great Justin's here hey Justin yeah we're super pumped three weeks three weeks from today we'll be on the show floor at the Rocky Mountain rep rep festival now see this is a little bit farther out here really hoping that these travel okay if not I'll let this sit and I'll loosen these up and let it figure itself out here got it whoo hey great five thank you this top bracket big brackets support it more okay yeah I'm working on that I think that's the next I lied that's not the next steps the next steps is the x-axis module which means we're gonna wire it with the big giant little back here we're gonna put this big cable chain in and it says the image on the left shows the installation points for the x-axis drag chain place the drag chain on the x-axis module and then use 2m 3 by 6 screws that's these and then bend it and use 2m 3 by 6 screws that way and then put this other bracket on so that's what we're gonna do word word up homies I don't know apparently I lost it yeah I'm super pumped for the Rocky Mountain rep rep festival super excited and I get a microphone all week so it is the standard blue snips that we all know probably all of us know from other printers if not they're standard blue snips that we get with a lot of printers so here it says basically it shows me to bring it up here and there's like screw holes in the so this is your cable chain and it's a monster cable chain by the way but there's screw holes right here you can kind of see you know kind of see them in here right here and so they want us to secure that at the top of here so that's gonna come up like this and get secured to the top of the gantry looks like two of them yep two of them and then we'll secure the other side not a really great way to show you that so we're just gonna do it I can probably do a top-down view but I don't know oh yeah you can tend to see oops there you go there we go oh kind of love this top down you've been you've been watching forever you know I use that a lot let's see aerial arrival of the Magnetal X ooh that'll be interesting Torio right as to my location area okay so hey I'm super pumped to meet a bunch of you guys then coming up guys gals crystal's gonna be there I don't know she's still watching but you got to find crystal and meet her she is great people I know Matt will be there like I said Akuma mods Matt will be there man there's just there's a ton of people coming it's gonna be awesome no one love yeah so the price is pretty proud for the T300 what's the Amazon I just looked at the I have it up I should go look what's the Amazon price right now I should know that before I you know tell you to I believe there is a I do believe that there is a discount on their website going on right now okay so then it wants us to do this place the drag chain on the X axis module and then secure it great then it wants us to bend it back and secure it again so that's gonna be up here I'll move it over so you can see some bending it back and it wants us to secure it here again like like this which is cool definitely in there this has to come out and get plugged in there somehow but we'll work on that in a minute because that's not what it tells me to do yet 3D printing professor what's up Joe but make sure to try to print pet G with it no matter what I do I can't get it to print pet G I will have to check that out I have to be 100% fair and I said this a little bit earlier I have not watched anybody's content on this printer yet because I didn't want to come in with any sort of bias I didn't want to know how to put it together I usually do that for these I just don't watch it okay so we got that on there but I'm definitely gonna have to check that out Joe if you guys haven't seen Joe's channel the 3D printing professor you gotta check that out super cool channel not only that but he makes some really cool stuff printer blocks is amazing by the way let's see you got mine messed up on this step and had to undo it and do it again oh I haven't made a video about it because I got an early alpha and it was well needed some work nice this Joe will be there too awesome with polymaker yes oh gotta know what's going on with this camera nothing good huh give me a second give me a second you know what nothing good means I bet you I killed the battery and didn't mean to most likely because I didn't plug it back in like a dummy that's just not most likely that's exactly what happened so now I gotta do that quick and I gotta remember where my big my big boy charger is here but I'll be right back with your comments here camera's gonna look silly for a second here might have to swap this bad I'd made a the bad mistake of not plugging in my camera and it definitely died did not pay attention let's see if that keeps it charged here hopefully it will let's see hey oh it's not happy about it 529 on Amazon nice alright give me two seconds I just got swapped this battery rookie mistake I can turn rookie mistake yeah normally I have this plugged in all the time I just when I I moved the camera around to film something else and I forgot to plug it back in didn't pay attention to the battery that's French for the battery if anyone's if anyone's French in here you know you'll know that not really there we go there we go there we go presets are good I'm gonna put this battery over here so I know I need to charge it there we go sorry about that boom now we're back whoa check out that flicker what is causing that you see that that's some serious flicker huh I'm sure what was causing that we're gonna flicker alert flicker alert is really weird I I have a fan on I don't and it's the same lights I use on every single video here let's see something you know what it is it's the monitor over there look at that gone almost a little bit right here I have a big monitor right this way showing comments and I bet you I have the brightness too high and it is throwing off some crazy whatever we're gonna deal with it all right here we go I didn't see it doing that before did anyone else see doing that I'm gonna have to go back in the video anyways it might be but I this is the same camera I use on every video in every live stream and I usually don't see that difference is I have that monitor a little brighter than normal I bet you that's what's going on okay here we go now there's a bracket that needs to go over here somewhere and and hold this stuff up is from what it says so it says secure the drag chain got it there and let's see so I think Joe said this might be where he messed up and had to do it again and I'm just looking at where that could be where do they want you to do this got to be somewhere with two screws not appear I did that part and they're long and three by 30s okay that's done I think you got it right nice there's this next step where this little bracket goes says come grow on it and now I just got to figure out where that part goes because it's not exactly clear I'm gonna show you the picture in a second here that flickers killing me I bet you that's exactly what that is it's that the monitor is so bright down there interesting it would make sense I've had that happen before so I have a big TV right here right next to the camera and I there's a new monitor right under the TV and I have it like pretty much maximum brightness and it's very large so when I do this kind of stuff I can blow it up and actually see it full screen it's the clip that holds the cable on the side great now I got to find what that means oh on the side of the printer here I don't see any areas for that I'll see any screws I'll show you what this this picture shows me because you know instructions and stuff so we just did this part right the top of the gate or the top up here then this next picture shows where it comes up here and bends over I think I see it I do see it I just had to actually pay attention here let me get you have a good shot of what this is because everybody on it's everybody's yelling probably right now oh you can see one of my lights there okay it's right here so this cable is gonna come down and hold in right there right there I'm gonna give it some slack I'm gonna push this in and then do that so then this says com grow on it you see that com grow got it yeah I just didn't know where it went cuz this I took me a minute push that in so there's a little extra slack I'm gonna grab this and my sweet tea handles maybe my sweet tea handle what is going on here have the wrong size what the heck do you have the wrong size no I didn't well that's super weird watch this see that it's just spinning in there but the next size up that was a two two and a half doesn't fit well that's odd okay weird weird I don't think it's this one oh it is that one I guess I'm gonna use the I'm gonna use the included one for this not my tea handle because I don't know what that was really weird I asked earlier but do you know if they do you know to know if they listen to me are the bags or screws labeled for step one two three etc. and don't match the steps in the instructions let me look sorry I didn't see that probably was too busy trying to figure out where the heck this bracket goes not yeah give me a second I'll look in one second what's weird is there's not really steps though maybe there is kind of it just says like I guess there is a one next to that make sure I get plenty of slack into this before I tighten it in not my favorite but this actually worked really well this I was I'm pleasantly surprised that these Allen wrenches have ball ends on them so that's a good thing at least okay let's check it out so this would have been step two technically this is step two M3 by 30 that's what we just did here before that it would have been M3 by 6 and that I mean if we're being we're calling them steps that's wrong that would have been step two like part one or something if we go back to the big ones which were the M4 by 16s that should have been I just keep throwing them in a bag here yeah that's a step three on it 4 by 16 and what's interesting is the very first thing we did when we put the uprights down is step 5 so yeah out of sequence a little maybe they just got the bags labeled wrong or something not sure but that's that's what happened so now we need to do the z-axis support profiles and that looks like it's gonna go on the back of the machine to beef these bad boys up and I'm gonna spin this around give you guys a sweet view of that there you go I just remembered that's right there now totally looked in the camera right now and saw that whoa all right so it looks like we're gonna drop these on and use m5 by 18 and m5 by 35 screws I'm in for a treat oh boy that doesn't sound good it'll be good con a good feedback for them I'll tell them the same thing we need to make sure that the we need to make sure that these bags are labor it's I mean luckily it has the screw size so if you ignore the step this might actually be step six to be fair it doesn't say that but it might be step six but this is not step four I mean I get it though I get it screws in the wrong bag labels on the wrong thing oh yeah 100% agree Joe if you're looking at this as a brand new user you're following you are following the instructions and to be fair they don't say step one two three whatever it says x-axis one x-axis two you know what I mean so it's not like they have steps in this book at least but 100% agree with you if you're a brand new user then I'm luckily looking for the screw sizes because or the bolt sizes because they match but yeah 100% agree so we're gonna do m5 by 18s in the top and m5 by 35s in the bottom what's up Andrew s council of Andrews in the house so I'm gonna do the tops first whoa whoa whoa and these should be this size and that's gonna be right here goes right in I am not gonna tighten these all down yet we're gonna get them all in first bad angle then then we'll do the bottoms they included their included slicers misconfigured they recommend orca slicer if you contact them yeah I I love orca bamboo slicer orca slicer orca slicer for this and I'll use it for this but yeah oh pke meter interesting do they give you a profile is there a profile anywhere for the orca slicer or maybe it's in there I'm not sure but you know a lot of times if you hit them up they'll be like oh yeah here's a profile again on the bottoms not going all the way down I'm just gonna make it almost tight and then I'll adjust and tighten a new user would just tighten these 100% because it doesn't say not to to be fair so where we're at is right there yeah yeah I definitely agree they need to have it on com grow and sova whatever if you're listening it would be awesome to have the profiles on the SD card maybe going forward they can do that nice for the flash forage that's cool of course my hand isn't the way why okay so they are oh they have a wiki now with videos okay cool I did see that they were working on a wiki I don't think there's much movement in this to be honest maybe a little that's pretty solid what I'm probably gonna do is just hold that tighten down there you go I could check it on the other side with a with a square just you know just to make sure we're square and I'm gonna just for the argument's sake I'm gonna do that so that one doesn't move too much we're gonna go for it there we go one more I'm gonna go top just tighten these in I've had no I've had this to be fair it's probably a pre-release pre-release it just showed up on my doorstep like a month ago or so I didn't even know I was getting it and then they reached out and like hey can you check out this this printer all right real quick for argument's sake for these yeah look at that I mean this is a cover in here so that's not exactly fair but interesting I mean up to the rail on this side's good yeah not terrible that seems straight I could do underneath the x entry x gantry as well alright yeah so no users new users might have fixed it's not sure but let us know if you got yours after launch did they fix that here's to be the same got it David clune so next it wants us to plug in the screen and that's gonna go on the front over here yeah that's you know they definitely I love to see manufacturers making sure that their their profiles and their slicers all the stuff is ready on the SD card for a brand new user someone bought this and never did this before it needs to be ready to go out of the box Renato I'm not sure if I agree but I can tell you this last year the Sobel SBO 6 was my favorite printer for beginners 100% hands down I mean for I guess I should say this my favorite budget printer for beginners best the best $200 printer you can get for a beginner it was awesome okay screen Sobel SBO 8 I have any other room I can confirm that I have it I can't talk about it much I could show you the box that's about it I'm not allowed to say anything other than I have it it's in the other room I will be building it today slash tonight probably tonight depending on the time here and getting it running and we'll see where it goes from there but I can't see say anything else but that yes seven not my favorite six great I'm gonna be did I do I don't know if I did the video on a seven that I did watch everybody's videos on and I did I don't remember if I did it or gave it away they might have told me to give it away I can't remember all right so screen so screen gets plugged in right there there's only one plug there's two clips they go in here kind of kind of fits in there nicely this should sit on nicely and slide down and we have a screen and for your viewing pleasure ready oh yeah there we go hey what's up BLD okay so screens on now we need to do the spool holder and then we'll wire it and we'll rock and roll so the spool holder I'm gonna change up here is very large which is great please remove a knob first loosen two screws at the top and front at the top and front of the left axis module by a certain distance no need to unscrew them completely once the spool holder sits into that oh I see then you can tighten it back down and put the knob back on interesting okay so if I'm looking at looking at the printer straight on this is the left side it looks like that's the side it goes on and they want us to see if I can give you a good shot of this oh don't twist pull on the knob straight up don't twist thank you appreciate that like a like a car knob right let's see if I could I don't know if I can get you a good view of this without oh yeah here we go there we go so right here if I can get you to focus there we go right here so he said don't twist pull straight up got it and he says the front I just want to sit it's gonna sit like this I think no it's gonna face like this so these two here you're gonna loosen up and then it'll actually slide into you don't have to take them all the way out it'll but it'll slide into I'm sorry so right here we are going to loosen these up I know it's hard to see because that camera and then the spool holder has it's not a it's not fully closed there you go so to slide onto those and then you throw up the calibration of your z-axis oh boy no one's gonna know that because they don't talk about that that I saw in the book I could have not read it yet I'm hoping they have us calibrate it okay almost so we're on like that down here and I'm gonna tighten those back down I know this is kind of a bad angle for a camera here spool holder is now getting tight check and then we're gonna take our cap here and push it on there's only gone one way oh it does so there's a flat spot I just couldn't see it there we go caps back on boom love it we should get the groove you but the ender three is terribly documented there's so many abandoned enders in a while because Crowley didn't document yes 100% no I you know what for a second let me let me let me throw this out there you know who did documented all of us and all of the users so Luke Hatfield especially right documented the ender three and the fixes like really good Crowley not so much the community they did but yes there's a bunch of abandoned ones because of that okay here we go we got a plug-in stuffs plug-in stuffs yeah Luke Hatfield is awesome that's how I started this channel because of Luke that is true I got my ender three ironically didn't know how to use it went to his guide for help never had 3d printed before and didn't know half the words he was saying in his guide so it's like I need help can I start filming this for other people like me and you can tell me what I did wrong on my videos and I'll fix them that's how I started so this is interesting I you got to kind of pull this out a little this hot end one it goes down in and it snaps in but make sure you have enough make sure you have enough cable in this chain to do that good thing I gave it extra there because I had to pull it pull it out a little I might have to go okay I may get a little more this actually floats which is nice too and I'm an idiot I just realized they taped oh I gotta show you this I don't know if they show this in the book I'm gonna look real quick they don't but real fast check this out this is tape I feel like that's where they want this right I'm just gonna throw it out there I wish they would have said that in the book or in the manual because yeah I agree Joe for sure hey wait Joe are you gonna be at Rocky Mountain rep rep festival you were there last year I'm gonna just fix this bothers me yeah the tape should have been under the clip I agree it doesn't say that though in the instructions so you know that's something that probably should be probably should be in there like hey put the taped part of the porch you know that kind of thing I'll get out of here apparently you got to take it off quite a bit hope it prints well me too I hope this tape goes under here without me taking this whole thing off get out of here something's got to be trapped oh it can't go you know what it can't I lied where this wire comes out here it doesn't allow it to go under there they can go to about right there I'll pull it up as far as I can so I am wrong nice David I'm just gonna leave it here and it's not gonna stay so there's that I'll try in a second this is all for not yeah I wanted to say the tape went under there too but it can't I mean like it can't no I'm leaving it I made a mistake yeah see it I have it tightened all the way down and it floats so too bad moving on so I got up here in filament run out hot end right there I got z-axis here done z-axis on the other side done I believe that's it let's look so you can look away with me z-axis good extruder great z-motor great z-motor great power supply didn't do that one yet and the filament run-out sensor I think we're good good good good dimensionally off on the Z by default interesting interesting okay so I connected wires main menu all right now now it's a moment of truth right we got to turn this bad boy on I think I have a power cable I got the leveling card here put this all back together it doesn't it does not matter to me how it looks as long as it prints good I don't care what printer you use as long as it's a printer you like and it prints good right two Z screws or single it is two and they're not they're linear rails on the on the Z here and there's two one motor on each side so there's two yeah for me grab a printer one that you like one that you can afford that's in your budget and print that's my theory on printing I don't care what color it is I don't care what brand it is I don't care any of that other stuff as long as you are having fun that's all that matters to me okay front here there's your USB I'm just gonna plug this in well it looks like there's two for some reason okay weird there we go like that that is right tour check the voltage I definitely should do that doesn't I don't know if it tells me to let me look let me I just put oh no here's instructions hang on power supply Z motor blah blah blah doesn't say anything about checking the voltage don't know if I can don't know if I can't see let's see there's nowhere that I see so far might be auto yeah I don't see it you guys want to see underneath though here there we go there's underneath rubber feet that's where it plugs in back here I don't see your motor sit down here by the way might be auto I don't see anywhere I can change the voltage I don't see any stickers telling me to change it so we're going for it instructions didn't tell me to do it I'm going for it like Joseph if you get this and you're brand new you're not going to check it because it's not going to tell you to so usually they they're good about putting a sticker somewhere it's in the instructions that kind of thing so make sure this is on okay you know what I'm going to turn this this way so I can give you guys a screenshot shot of the video turning on maybe without so much there we go tour though yeah there's no best printer the only one that's best is the one you're using that works for you and that you like I don't care what it is don't care what color brand any of that garbage doesn't matter to me here we pop this on you guys ready let's fire this bad boy up no smoke right calm grow all right haven't heard of that check I have to check it out let's see David Klune your go print 3d access dial and macro interesting I don't didn't help it hey David let's look at that let's check that out too maybe up the I don't know where you found it but I'll have to maybe email it to me or something that way you can check it out all right it's going it's not the quietest thing there's a fan in the bottom that's so far the loudest thing here it does have an inductive sensor up here I see it no make boom yes no make boom and move sorry probably even get you closer let's see now it's now it's worse yeah that light is right there huh let's see if I can do this there you go still still bad whatever you'll get the idea you'll get it there we go good enough so in here there's a home button it tells me a whole bunch of stuff so first let's check our touchscreen you got a light in the hot end that's on and off settings network that's not what I meant to do okay there's a calibrate button there is looks like prints maybe so far it's pretty responsive yeah not bad not bad sorry didn't link right I'm guessing the links didn't come through if you sent a link it's probably blocked but tells you at least they give you like a good overview of what the menu should look like and what all the buttons do so that's cool so that's cool I like that so we got to go to leveling check settings click level calibrate and then perform to perform the Z tilt calibration all right settings the first thing they want us to do is calibrate Z tilt guessing that's that one there and I'm gonna get you a different view for a second I'm kind of show you what it's doing I had this printer turned like all sorts of crazy so you guys can see the screen better but well now you can kind of see what it's gonna do here so it's running through Z tilt calibration first says when it stops please clean the nozzle do not heat it click to perform the Z offset calibration okay now it's going back up it's turning the knobs at the top there sorry about all the crazy light you probably see it here too which camera this one this one this one I'm not sure what is sticking down oh you can see that interesting you can tell I don't have this zoomed in far enough when when you can see this back light here this one here is this one here's just a GoPro that one very good for for a GoPro I'm gonna fix this though see if that fixed it yeah I I really like for this let's see almost fixed it this is just a GoPro running HDMI mini to HDMI or HDMI micro really here we go to HDMI and sorry I needed some water yeah so we're here great it did its thing yeah this one bam GoPro and I have it on a try a little like you know extendable tripod so now it says to do place the leveling car between the nozzle and the hotbed let's see not when the nozzle stops moving please clean the nozzle and do not heat click to perform Z offset the nozzle looks clean to me so let's do our Z offset so I just clicked Z axis calibrate on the screen and it looks like it's gonna heat the bed up to 60 C it's at 27 right now so it's at 30 so it's going pretty quick let me know in the chat if you guys have any questions this is the Comgro T 300 yeah this is a beast it's a monster no it's this one's an older one this is a seven hero seven black I haven't I have an eight I believe two but one thing I like about the hero seven black edition I'm not sure about the other ones is that they had each USB-C charging and a mini HDMI right in the side so I don't have to add on the the media hub thing to get those so I always pretty much use my seven black for this setup to show things on the desk close during live streams I do have an eight I want to get that one going to because I think it's higher resolution but honestly this is only putting out 1080 so it's not that big a deal I'm not streaming in 4k my normal camera here is a Sony a7c2 so that's my normal camera and then the one up top is a Canon SL3 it's one of my older cameras now but I just use it for top-down when we're doing this kind of stuff okay so I'm gonna leave that here we're at temp all it says is put the leveling card in constantly pull the leveling car between the nozzle until you feel resistance without crushing the card completely and then click save okay so we can do this that's fine that basically use this I'm gonna go down it's only point there we go now we're doing point one at a time getting some resistance not yet I might have to go down more fast at least oh there we go go back up one don't crush the card completely it says remember that means that was weird okay yeah I like about right there we'll do one more just because I'd like a little extra squish I'll hit save like it asked me to do saved next click for mesh bed leveling and complete that so I'm gonna go down here it says heated bed leveling I guess that's what we're doing let me get this out of here I didn't crush the card what kind of weird Z tilt macro is that normally with z-tailed it moves right and left along the edge and levels it interesting not sure you have to print the dial for the right post and then give it then give you in minutes what adjust the right rod to get it level it reads out the men's you just need to adjust the CW or CCW and run it again interesting cool right now we're running auto leveling and I just turned like like a crazy here there we go I should be facing that way I like it there we go but we don't need to see that for now right now it's heating up we're gonna do some leveling I do have it sideways because when we print whatever the print is I'm guessing it's gonna be I'm hoping it's a benchy because it says it's like a 15-minute benchy then I can put like this right here and slam you guys in close and get hopefully a good shot of said benchy right now it's gonna start some bed leveling I'm gonna grab some water and I know there's a bunch of us here what are you guys drinking today Shane right now I'm not printing with any filament this this is the filament that came with it and that's what I'll print the first prints with just see what it is offset maker lounge lounge I said lounge what's up offset maker lab Sam Prentice has given me a hard time it looks like let me just see yeah we got this really good PLA white in a 200 grams that's what we're gonna use and I'm way out of my light there we go lounging Sam would never yeah right he's in China right now I believe sucker I wanted to go should have went what will I be printing I'm gonna be printing with this stuff that they gave me all 200 grams of it and probably not 200 grams but you know what I mean this this filament right here I'm guessing it is Creality PLA if I have to guess I'm not sure it just says PLA white 200 and 200 grams I'm gonna get that ready while we're talking next time we'll go and not invite him right congratulations on the engagement again and I can't wait to see you offset maker lab the crew will be at at Rocky Mountain rep rap festival in three weeks three weeks it's gonna be awesome so I'm pumped to see you there too I'm just gonna bring this down and put it in the filament runout sensor I probably should be doing this while it's leveling huh let's stick it in the end instead of like jamming it in there while it's trying to level I gotta say this leveling is pretty fast here well of course right right I get to the end and so now it says please confirm and save it okay I saved it done in the instructions it says print something now so that's what we're gonna do boom working on Steve's car haven't even started printing it okay we have you have a bunch of printers in three weeks we'll be okay right have you seen the beacon beacon leveling it's bonkers no don't know what you're talking about so I'm gonna go see what's on the disk please be a benchy it is it says 12 minutes 12 minutes kind of cool let me show you the interfaces I like this if I can show you really nice it's it shows picture of that model 12 minutes 2.9 meters of filament we'll hit print so you can kind of see we are able to adjust the Z offset it looks like which is good I could turn the light on and off right here it looks like it's gonna go do some stuff now the bed leveling is terrible as soon as you can route it I would install camp immediately that's quick bed leveling oh wow the firmware improves the screen layout and functions oh there's firmware what's up Matt's maker space I should probably if there's new firmware for this I probably should check that out so yeah I'm gonna get on the adjust button let's see there we go I got my adjust going here oh you know what I can't print without loading some dang filament what a dummy I am that would have been awesome here I am not paying attention we're good okay filament loaded whoa crisis averted boom so right now it's heating up I'll get out of here it yelled at me because I it didn't it didn't detect any film so at least it caught it right yeah now it's spewing out in the end there perfect that would have been awesome camp is built in the clipper you said to have adapted equals one at the end of your whoa what does that do I am terrible with clipper I am not good at clipper I need to get going better on it see if I can burn my fingers there we go there we go I'm in the adjust phase how do I tell it to print now I go hang on play now it's spewing out stuff again yeah it's adaptive mesh so you don't probe the whole bed just where it's printing oh that's sweet that is sweet I hope I'm printing here let's see what's going on it's at 250 250 on the nozzle whoa and 60 on the I'm not sure what it's waiting for right now to be honest didn't even burn myself it's just chilling I don't know what it's waiting it's not doing anything look it's just sitting there I have a play button I hit it twice now I go on I could hit stop thank you tour Dan thank you yeah I don't know what it wants me to do here stop no how about just print it you're heated up 250 60 C what are we waiting for maybe it was mad cuz I loaded filament in while it was printing we're gonna stop it I'm gonna go here and then we go to Benchy print okay now it's not paused good now see what happens there we go thank you she had a good time thank you tour appreciate that see you in three weeks man the delay gets fixed in the update okay so I'm at the look for the firmware 3d I wouldn't I wouldn't I would not say it doesn't so currently whoa there we go I was gonna say I can't see that is rocking and I can't see the first layer to tell you at least there's like a cut out in the front so you can kind of try to see it it's just so fast that it's so fast that it's going right we're doing it holy mother of mercy shush that thing's flying I mean it does say 12 minutes but 11 minutes left right now I'm gonna have to check out the firmware so is the firmware on their site I'm assuming the firmware is on their site I'll have to do that I'm guessing there's a screen firmware and there's a firmware for this okay good in the wiki okay I'll go check it out man this is flying holy moly so those of you have done the firmware what's it all fixed I see screen UI let's see what else wow oh the delay there's a delay holy man this is crazy it is cruising this thing is violent too super heavy all made out of metal yeah let's let's check out the website real quick I'm gonna check out the website real quick because I think they have it on sale I need to get that link in the description holy wow things shaking my new desk here limited time there is a discount in limited time there is looks like $50 off Dan Adams thanks for see thanks for popping in man thank you yeah let's see Joe you're right it's crazy right now there's a $50 off code on com grows website you can get it for 50 bucks off it is going for $549 on their website so you can get it for $500 or $499 really is what it would be some of the cool things about it it's based on clipper we know that 64-bit computer in there all metal absolutely it's all metal this thing is this thing is a beast it is heavy looks like their extruder has a six to five to one ratio which is awesome per perfectly balanced build area is what it says rapid filament cooling yeah there is a giant fan on this thing 50 it's a 5025 fan at 800 let's see 8500 rpm they say it can run 600 millimeters a second I'm sorry I said 300 earlier because that's what the book says but on their website it says 600 millimeters a second 12,000 millimeters squared that must be the acceleration maybe and then it'll push the extruder 30 millimeters a second whatever Benchy 13 minutes and 40 seconds they have a picture of that 30 second heating they say that it takes 30 seconds to heat interesting 4.3 inch touchscreen which is really nice 81 point bed leveling gotta go if you try PTG let me know I just want to know if I got a lemon okay definitely Joe thank you for stopping by it was great to see your name in the chat and also if you haven't been following 3d print professor go check out his channel super cool channel a lot of really cool in-depth dives and I love the printable if you haven't checked out printer blocks you got to do that too where we at here yeah alright we're rocking man this thing is rocking just so you know it's 529 on the link I gave for Amazon it is 529 and that is with Prime shipping so that just a heads up there's free Prime shipping at 529 on Amazon and that's the link I do have in the description below if you're looking for it you know as always this is not a review this is a you know basically an unboxing first look let's get a first print going let's build it would have been way faster if I would have not been filming and not been talking and just put this thing together but it doesn't take that that long let's see just looking at comments here great I need to go I really do need to go get that firmware it looks like get the firmware rolling this bench is looking pretty solid so far but this thing is rocking man whoo rocking Jonathan Barnes I like Lindsey's video the other day thank you thank you she did a really good job see it was her first time I showed her how to work everything in here as far as to record the videos and that kind of stuff and she just went with it so I didn't stand here I didn't help her unless asked which is very seldom which was more like a camera question other than that she rolled with it so I think she did a great job especially for her first video that was really cool and she did really good information she is printing so small like I cannot believe some of the stuff that comes off of the printers when she did she designs a lot of it in tinker cat actually and then prints it and it's crazy crazy this thing is a beast an absolute beast it is solid as a rock it's heavier than a mother and it is moving wow this thing is moving I think nerdy L has the potential to stick up to ask her up to ask her I really want to build the other machine I have I'm gonna leave you with this for a second I really want to build the other machine I have but I can't I don't know if I'm gonna get time I got to go do some running around and grab some stuff for Easter I definitely can't build it on stream because I can't show you the machine yet but give me a second I'll give you a sneak preview maybe if I don't crash into everything in my dark room over here especially this giant orange storm giga that's in the way let's not run into that all right here we go I am not sure what I can show you I don't even know if you guys can hear me right but oh this thing is a monster and I am gonna do this anyway I can show you the box I think I can show you the box oh this thing is a monster so let me see what can I show you I'm pretty sure others have already showed the box so I can show you that this box is heavy as that one is man let's see Shane that's funny the answer is not yet I need to I really really need to that thing isn't a beast of a machine as well and I really need to get that thing going I should do that okay I can do this real quick I can show you I believe I can show you the box it's an SVO 8 by Soval I'm gonna double check because I don't want to be the bad guy so while this is printing I'm double-checking quick to make sure that I can show you the box okay I can show you the box and I can tell you that it's a Soval SVO 8 and I believe I can share that it's 350 by 350 by 340 that's what I can tell you so far how about that how about that I'm gonna use orca yes linear rails yes I don't know if I can show you this I don't know if I can show you that yeah here you go Soval SVO 8 spool holder I don't know what I can show you how about that but I can show you that I could tell you it's 350 350 by 340 nerdy is cool I have not looked so I cannot tell you if that's true or not I should look and see if anyone else has showed a picture of the I thought I saw a picture of the box which somebody actually showed this thing but I can tell you it's core X Y2 not sure if I'm supposed to tell you that but it's gonna be a fun machine I am I'm super pumped to build it and a nice nice spool holder yeah it's an SVO 8 I can tell you it's 350 350 by 340 it said and I had to block out some parts on the box because I can't show you the rest of the words on the box yet that's why there's tape on the box trying to be good trying to be good on the holy mother of mercy you see how fast it's doing that stack it's definitely sliced to go fast we're at zero minutes left we're gonna see how fast the screen said that took of course it's white film it so it's kind of hard to show on camera 14 minutes is what the screen shows 3d Benchy maybe there we go 14 minutes David loves so far loves it detected that the offset is modified you want to save it now that's cool yes I do thank you for asking I do like that because it didn't let me save it while I was doing it during the print whoa just rip it off the bed yeah I definitely need to come down further anyway but I'll show you what I got okay if I do that yeah so it is really white and blown out that's what happens if I do that so hard to show you in a white filament it's not perfect but it was fast it's so hard to show you let me see maybe this one has a little better there we go yeah it's a little better definitely not perfect it's sliced to go fast big layer lines bottom needed some help on the first layer Z offset well figure that out I already knew it was a corax why nice you don't there is some stringing in this in the Benchy itself very hard to show it but there is some in there and I'll just throw it across the table because that's what I do he's been flying there it is oh it went in a box so let me go back here because I got to pick it up hang on I got it all right so it was it was 14 minutes and it's not perfect but you know it worked it fit right on the bed like that you know good Benchy I definitely need to update the firmware but you know I think it came out well came out very good in the white filament again hard to see on the camera that's funny just to give you an idea this is the one we just printed 100% 1200% oh I already see a crack in this one that's not fun I've been messing around with it too much but yeah not not perfect not the best Benchy I've seen off of one of these that fast but it sounds like there's firmware that needs to be done it sounds like there's tuning that needs to be done on this machine and it's gonna be a pretty pretty solid machine I mean it is a solid machine it's all metal so there's that the ship jump ship I can tell you that again it's really hard to show you that hole right here is not round definitely not round right here a lot of thin layers up top here some stringing but you know what for a 14 minute Benchy first print off this print with nothing other than what the instructions told me to do solid first print David Klune says his is going for like a month he'd like in it very happy not much tinkering print quality is good and support answers questions fast which is great so now I need to go do the firmware I'll go on their wiki and grab the firmware do that it'll probably be a board and the screen firmware like most of these clipper machines and most of the other machines with touch screens yeah any questions first initial comments initial thoughts on this machine is that it is a absolute monster it is heavy it's metal a lot of metal that does have it definitely does have linear rails has a lot of support to hold everything up and guide it definitely you know it's interesting it doesn't have a brace across the top but you know who says we need that right dual Z touchscreen 300 by 300 by 350 I believe man solid any someone says dope any other questions any questions let's just do this thing is it's huge you guys are awesome so that was it we printed we unboxed it we did the things I'm gonna do more things and have some fun I know come down here oops I just want to make sure I'm not missing any comments I'm not good good good so yeah love it com grow nice work you know again this is not a review this is an unboxing first print and assembly but initial reaction initial reaction is it's built super strong it's heavy and it's very fast it sounds like the firmware is going to help so I'm gonna work on that next when I can when I get some time to do that blasto what's up yeah I'm gonna work on the firmware next cuz it you know like like they've said there's a firmware for it that should help and maybe we'll print something huge and fast I'm gonna use orca slicer that's what I'm probably gonna use is orca slicer it looks like you can get the profile from com grow it might even be an orca excuse me orca excuse me already so I'm gonna work on that other than that cool machine very cool and bill and bill like a tank absolute tank if you have this put it on a very sturdy table because it was it was rocking not a terrible Benchy not the best I've ever seen but not terrible definitely could improve and I think it's just I think they sliced it to go as fast as possible so there's that and I think with the extra calibration that'll help too so yeah with that being said I think I'm gonna bail I'm gonna go hang out with the family and get some stuff ready for Easter tomorrow you celebrate Easter happy Easter tomorrow if you don't happy Sunday so there's that yeah other than that cool thank you guys so much for being here I really really do appreciate it yeah blasto how heavy the T 500 was it's a month this thing is a monster too it's like 48 pounds shipping weight is what it was good luck everyone yeah bye all we'll see you guys in three weeks at the Rocky Mountain rep rap festival check out the video on my channel if you don't know what that is look it up because it is such a fun time it's gonna be in Loveland Colorado which is just north of Denver and it is in three weeks over April 20th and 21st I believe they got a monster ballroom or two monster rooms is what basically what it is I get to be the MC they're giving me a microphone for the whole weekend which is crazy and we're gonna have some fun with everybody that comes out Andrew s thank you offset maker lab I keep saying lounge I don't know why but thank you when thank you John thank you Jonathan Barnes Shane thank you but yeah hopefully we'll see you and that is you know again my my trip and stuff we're gonna be sponsored by Soville which is also Comgro they kind of merged and we have some really cool content coming if I can do it I'm gonna have the brand new SBO eight out there as well on the table so come check that out other than that have a great Saturday everybody have fun I hope you have a great weekend if you again celebrate Easter happy Easter otherwise happy Sunday tomorrow to everybody and we'll see you guys in the next one no hot makes on Monday this week maybe I'll go live and do something different though we'll see bye everybody have a great night thank you guys for being here and you rock see you later