 Okay, guys, so we're gonna try to build a fishing pole here. This is from what we broke. Well, what I broke the black max today This is the end of A two-piece pole this this one got broke by by a turtle I think this is one of her dad's old ones But I saved it because I liked it that in broke off there So what I'm going to try to do is take this end from the black max and I got to cut them I'm going to try to splice in two together and I'm going to do that with some shrink tubing After I cut the ends off just to get them to fit and then I'll put some shrink tubing on it So first I got to do something about this eyelet here And I'll tell you about the idea I got for that here in just a minute Okay, so what these they're supposed to have a piece of plastic in it like this Let me turn you around here Supposed to have a piece of plastic like that And that's what holds that up there, but that plastic is broke off. This is an old rod but I like it and It's better than trying to cast with that deep sea rod. Well, this is kind of a deep sea rod too You can see how huge that thing is. There's my thumb But at least I'll be able to cast this somewhat until I can get another rod So since you can't take these plastic pieces out and replace them I'm going to try to solder that in the place now what I could do is Take one off of my the black max that broke. I can cut it and take it off and I Put it on here and wrap it but I you need super glue and I can't find any super glue and What I do is I just cut it off clean that off and I put another one on I'll super glue it just tack it in place And then I'll wrap thread sewing thread around it over and over again I'll keep putting a little bit of glue on it over and over and that's pretty much all these older ones are The newer ones now or just that kind of thing right there so Yeah, so the first thing let's do I Won't get this plugged in let it get heated up and we're gonna try to solder this On here from this side. So that way You know, it doesn't cut the string that plastic is supposed to be more forgiving on your string But I don't think that's gonna be I don't think it's sharp enough to cut my string, but we'll find out But right now like I said, I don't have you well. I got super glue, but I can't find it If I'm the thread I need but I'm just not going to just wrap it with thread. I like to put blue on it So that's what we're going to do. We're going to try to do that and Hopefully We can get that fixed. So I'm going to get you set up here where you can see real well or well the best I can Get you to see and we'll solder this first and then we'll cut and end off of here and Then and off of here. I might just grind it on the grinder. This is fiberglass and I'll just go just enough to where this Will slide into there And once it does then we'll figure out which one of these we're going to use to put it together with This one I got because I may have to put a piece on here I don't know to make it a little bigger to For it to hold right, but yes, it's broke there anyway, so Yeah, that's what I'm going to do while this is heating up I'm going to go ahead I'm just going to hit them on the grinder real quick nothing to see there and just just until This will go inside of here and I'll be back with you guys. Let's let this heat up Shouldn't take very long Okay, so I got some of this too That we're going to help put that together with and If soldering doesn't work on this we're going to we're going to JB weld that too, so first Feels pretty hot, but there and get some on here first I may have to run this on the I don't know what that is might be stainless This might not even stick to it, so we may have to use the JB weld No, totally not one stick All right. Well, let's go ahead and get the JB weld out here. This is the Stuff that works on pretty much everything I'm sure to work on that it's got to wait 24 hours, but I mean It doesn't take a long to set up But to put it to use which we're not going fishing tonight anyway so now Mixing trade a little more than I wanted, but Then you pull this up a little bit and looks like more of the Stuff came out than the hardener, but and it's a lot more than what I wanted seems awful thin Compared to the stuff I'm used to using. Yeah, it's not even hot all right, so let's Put a Dippy dab on there And put a Dippy dab on there get some down in to the center one Let me get a toothpick Probably should have done this first, but we get a toothpick so I can get it down in the to the center This should work I think I've used this before on something like this Now what we're going to do is we have to try to get This isn't this to Good to try to get this tube up over here first. I'm gonna I'm gonna cut that off Because we don't need that much of it This is going to go All the way up in there, so we're only going to need Make sure this will get up over top of that other piece too Yeah, okay, so we're only going to need that much But I got to get it slid over this and then back over top of that Then we'll put our epoxy on it and see that's I got a box of those with bigger ones than this But I can't find it Try to get it lubed up See the problem is this gets fatter as you go down through here. I might be able to Put it in the freezer and shrink it down a little bit. I may try that Yeah, I should have done this in first before I did this, but that's all right So I'm gonna keep messing with this might see if I got a bigger piece than this but I'm gonna keep mess with this and Try to get because it's got to go clear up to here At least up to there and then I can slide it back over All right, so I'm gonna mess with that And then I'll bring you back once I get this up here and we get ready to put these two pieces together All right guys, so I ain't even joking Here's what I was talking about my heat shrink tube and it was right in the first place I looked if they weren't there because that's where I keep them and First they weren't there I just went back in and I looked well I look two more times after that, but I just went back in thought I'd look again and you know what? There was so All right, let's go ahead and Put some of this on here Now I'm gonna use two pieces This is going to go over top of that and then this is going to go over top of both of them So all right now we're gonna Put this inside of here Just like that I'm gonna slide that back because I'm gonna heat that up. I got to grab my lighter Well, I think monkey's got one over here. Let me go grab my lighter first let's make sure Straight down through there. They're all lined up and They seem to be All right, so there's that Now let's slide this over there You guys ain't seen nothing probably could use my torch, but I don't know why that's doing that But it's gonna work All right, I'm gonna keep doing this for a minute Then I'll kick you guys back on I'll show you what we came up with okay guys. There we go On there, I can't pull it out But once that stuff sets up inside there, too, I just put this on kind of to keep the The glass the fiberglass from splintering out after a while And to help hold it together while This stuff dries overnight So there's what we got Um, that's gonna dry. I'm not gonna put the raw or the real on it tonight, but This is the rod I'm gonna put it on here put it together Just like that there we go now we've got Looks like a seven-foot rod So yeah, that's gonna be all right, so I'm gonna take this back out Let this dry overnight and you'll see it next time we go fishing Yeah, I'm just gonna Let that hang While that stuff dries up and be ready to go next time. All right guys. Thanks for joining me. Thanks for watching it's about 40 minutes after 12 so it's 12 40 12 41 right now It's another late night video, but yeah, I'm just gonna let the weight of that. I May set it on something and then hang something on it. That's probably what I'll do But yeah, this thing will not pull out. So And I can't get it to turn so hopefully it's straight enough. Let me see Yeah, I think it'll be all right Looks pretty good. All right. Thanks for watching guys. Shaber and myth me and legend gone for now We'll see you guys in the next one. Bye. Bye everyone. Take care