 Hi, this is Kevin from BCH. Today we're going to refill HP cartridge. We're going to use this HP Photosmart C4795, which uses the HP 60 cartridge. This is a very old printer. We use this as an example. So we're going to use a minimum amount of tools. And we're going to show you how to refill it and how to clog it and troubleshoot it. The same method can be used on 61, 62, 63, 65, or the integrated cartridge. We don't know anything about this printer. We know it has been a luggage for at least a suitcase for at least two, three months. And before that, probably it has been in storage for like a year or so. So let's print a page. Let's ask who that's new. For the first time refill, we suggest this kit, EZ30T. It can be found at bchtechnologies.com, under Refill Kit, Fridge P660. And you can see the EZ30T. Some of you might bought ID30-KKK or ID30-KCMY, which is the same as EZT, but without the priming clip. So don't panic. In this video, we're also going to show you how to use ID30 and ID30-KCMY without the priming clip. The ID30 can be bought from bchtechnologies. Then you go to Refill Ink instead of Refill Kit. You go to Refill Ink for HP. And the quickest way you can select a total ink volume is 120 mil, which brings you. You either can do ID30-KKK, which is K means black. It means three blacks, three blacking, or ID30-KCMY, which is a black, cyan, magenta, yellow. So it basically is black plus colors. Those ones doesn't have a clip again. But you don't really need a clip to do this. Let's unpack a full kit, ID30-T. You have a black clip called a priming clip. Then you have two silicon pads. The blue pads, one is for color, one is for black. Then you have syringe. Because you have spring bottles, you don't need a syringe to add ink. This syringe is for the clip. Then you have four bottles of ink. The ink is exactly what you're going to get if you get an ID30 kit, like ID30-KKK or ID30-KCMY. There are also some toothpicks in the kit. The toothpicks are not for your dental hygiene. Those for poking in the cartridge and see what color is in the cartridge. Now let's take a look of the cartridge. At home, you can use your smartphone to zoom in. And this is the best way to check the printhead. On the bottom is the printhead. You can see the blue is leaking. And it has been dried for years. So probably the blue will give us the most problems. We need a softened dried ink. So we fill a bowl with about a quarter to half inch of water. And then we put a printhead on it. If you want something more powerful than water, you can go to bchtechnologies.com and go to accessories. And you'll go to the anti-clogging agent. And then we have two kinds of cleaning solutions. One is green, which is a little bit more powerful. Another is the clear kind. And it's a little bit cheaper. The black one is clean and I don't see any scratching. So that's good. You can use the warm water or you can heat it up with microwave. I mean, heat up the water with microwave. Or you can heat up the cleaning solution too, so make it more powerful. There's no set rule how long you need to soak it in. And just soak it and make some prints, see if it works. If it doesn't, come back and soak it a little more and do more on clogging. I normally soak about 20 minutes for the first time. Let me show you the top cartridge. You're going to find that for the black, there's a dent right on the top in the middle of the cartridge. You just need to poke a hole and add ink from there. Let me show you why. And the inside cartridge is the sponge, which holds the ink. And then those holes are air holes. And then you can see a series of long chamber that connects the air hole to outside, which allows the printer cartridge to breathe. So you don't need to get it airtight. We just need to add the ink to the sponge. And we can use any kind of tape or anything to seal the top. We use the drill bit to punch a hole in the middle. When we insert the needle, we don't want to go too deep. Just penetrate the sponge a little bit. And then we squeeze the bottle seven times. If you see the ink comes out, you can stop and let the sponge soak in a little bit. Then do it again. You can see the black cartridge is completely dried. Even when we add ink, there's absolutely no ink comes out. Here's when we're going to use the priming syringe to unclog it. However, let me show you how to do it without a priming syringe. You got a piece of paper towel and fold it three times. And then add some water to it. Get your vacuum cleaner and set to host setting. Put the cartridge on the paper towel, wrap it around, and use the vacuum hose to suck underneath. Do it until you see a lot of black color comes out. If you see no color, just soak more and just suck more and repeat. Then we just add a little bit more ink to compensate what's been sucking out. Now we work on the color one. I'm going to take the label off just to show you. But you can just do it over the label. You don't need to peel it off. There are five hosts. The top one is one color. The left two hosts are one color. The right two hosts are one color. OK, this is yellow. Then we'll use another one to poke in. And this one's magenta. We're doing three squeezes for each color. We try to get four squeezes in. But in most cases, three squeezes is all it takes. The ink may come out as soon as you remove the black cap. So just be careful. In this case, we just have a piece of tape, cover it, and just make sure that you don't seal it airtight. Leave some air. Leave some air space. If you're paranoid as I am, you probably want to just poke a little hole on each one. Now let's use the priming clip to illustrate how to unlock with the priming kit. We have two silicon pads. One pad has a longer slot than the other one. The longer one is for black cartridge. And the shorter one is for color. We install the silicon pad on the stand. Some people complain that the stand doesn't fit. It's too short. Actually, it's not too short. It is built that way so you can have an airtight fit. So put on stand and push down and press in. I'm pressing hard. And you will hear a click and it's in. Use the syringe to create a suction from the bottom. The ink should flow out if it's not clogged. Now you can see that it's completely clogged. There's no ink coming out. Magenta is unclogged. We're going to just soak more and suck a little bit more. We're going to steam a little bit to open the pores. We're going to use a steamer. If you do not have a steamer, if you have a steam iron for ironing cloth, or you can just have a bowl of boiling water and just wave it on the top of the boiling water, waving in the steam to open its pores. Or if you wife or girlfriend have those official steamer and that those can be used to, just don't tell them about it. And we'll put it back to the clip. You can see a little bit of yellow. So that's good. So we've got magenta and yellow working. Just add a little bit more ink. We put it back to the printer and see what's the current progress. We already unclogged the magenta and the yellow. And you can see we still have problems with cyan. Because the cyan was leaking, so we suspect maybe it's dried inside too. So we just left the cartridge in the printer for a day to have the inside softened. Then we took it out. And we're putting the priming clip again and the drawing out. And you can see the ink got darker and blacker. That means the cyan starts working. The refilled cartridge will not show actual ink levels. They will always show low ink or ink depleted. When you see the warning said the original cartridge has been depleted, just click OK. And now the printer will just keep printing. And just pay attention to the print out if a color is missing. And just add more ink if you have straps. And just do the unclogging as we did earlier. You can see after we click OK, the ink level of black becomes a question mark. That means the printer will no longer track the ink level. So we can print forever. And just pay attention to the ink, to the print out quality, and add the ink as needed. In this video, we showed you some basic refilled and unclogging and how to deal with the ink level. I hope you enjoyed this video. Visit us at www.phtechnologies.com. Cheers.