 So here's what we've got up to on what we've got up to on Tuesday. One, two, three, four, eight, ten, fourteen, sixteen, eighteen cuts. We've got to do an outro again. Ooh, my favourite time. Seven, forty, seven. I missed them planes. So it was storm-agnus yesterday. We were away doing an inside job, doing a door. So here's what we've got up to on what we've got up to on Tuesday. So, we haven't got a flat start, but... So this, I just took this up to use the mortar up. So it just seemed to go on and on. It just never ran out. So I've got two courses on. So now, because we've got two courses on, I can work all my cuts out. So I've got the big mill walkie set MX saw at the front there on a pallet. Alex set that up for me. I'm ready to do all the cutting. So I'm going to get all the cuts done up to the input. And while I'm doing that, Alex's getting a mix in. And then he's going to do some block out. So hopefully we'll get... Well, we'll definitely get all the block work up. See how we get on the brick work. The trestle's in the van ready to go up. We're going to trestle on the inside as normal, because then we can get all that off the trestles. And then when we do the sides, we might bring our little scaffold up to get the height on the pikes for the rake going up the wall. So yeah, we're just ready to carry on now. Just get ourselves organised. Like I said, I'll go and get the work out on my cuts. And then go make a mess. I'll switch off now. Once I've uncovered everything, I'll run you through what the cuts are going to be. Right, so we've got six courses up. So we need three more courses up to wall plate. So we need... That's a full block. So the only cuts we need on this elevation is this. So we need one at 100. Full, peaceful. That's that side finished. So we need... That's a cut. So that's 410. So we need 2 at 410. 8, 10, 14, 16, 18 cuts. And that's without doing the pikes yet. And I don't think we have a course and brick up to our lintel. I guess there is a course and brick in that. There is? Yeah. So I might just cut them down, lengthwise. When we get up there. Probably when we get up to window height and then there's less cuts then. Right. I've got to be cut so Alex can finish the mix and get a few more blocks. What I'm doing here then is obviously getting my stacks here. I'm going to do two stacks of 20 blocks here. And I'm just putting all the pieces here. So when we need them we can just find them here. Instead of keeping this part all clustered or keeping them all in one place. That way we need to grab the half and just grab them here. Because thankfully Dad is there label which ones which. So I'm just picking out from my little pick and dip mix over here. And yeah, I think he's almost done with these cuts now. So I'll get these last ones moved. Mix is ready. It's just having a few last spins so it's usable. This fed isn't the best. But I figured out how much I need to put in to make it decent enough. So I'll get here. I'm going to sit back up and we will get cracking. Mix is on. Alex is playing half way through the blocks. All the cuts are done. I think it's 18 or 20 cuts. That took me 10-15 minutes tops. And there's still three bars left on the bathroom. Just start building a little corner here Alex. You can just ruin it. I'll get myself a board here then. You put me a bucket on. I'll get a sack and a mix on while you. I'll get a sack and a corner while you finish off loading out. I'll mix it up good enough for you now. What? I'll mix it up good enough for you. Don't forget to stick a stack of here. Just to throw up on the trestles. So we'll get one last course on top of this. And then it's ready for trestles like this. Only because these bricks aren't set as high. So we'll go one above and sit on. Get this one on and then we'll have a quick break. Maybe we'll turn that thing for this one. We're up seven. We'll get the trestles out of the van. Get the planks on. And get loaded out. And carry on with the face work. Break over. Do anything done. Looking good. The trestles in. Do you think it's worth taking these boards up now so we can get the trestles flat on the floor? We'll just leave them in for cleaning the floor. You can take this one out. That's still pretty much flat. And we're going to need to elevate one of them anyway. So we can elevate this side. Good thinking. We need to get those blocks in as well. This is the first time. I'll just bar in the way that we've been in. Move some stuff around so I can get the stuff. Okay. Down there's the before. So yeah. If you bring the trestles down, I'll help you with them. I'll start putting the profiles up. Profiles there. Cool. Let's get the profiles up. And the profiles need to cook again now. So what I can do now is get the laser level back up on this cast iron pipe, which is perfect. Shine it across to our lintelite on the house. And then I can transfer the levels onto the profiles. So we make sure we finish bang-on level lintelite. And instead of putting a pen or anything, I've got a bit of electricians tape there. Just put a little bit of tape around. Can't lose your mark then. So I'll just nip the toilet, so I'm going to get these levels sorted out now. I'm looking up at the white sky, so I couldn't see it. I still can't see it, but I've just seen something down there. So let's try it from here. There you go. Works nice and level, as you can see. All those are lined there. That's where we put the whole lintelite. And then... It's definitely just above that clip to the left-hand side. That clip is just the left. So I'm going to get the tape up on there. And that's it. That's our level. And now we've got something. We've got our gauge down now. So we're all nice and level. Let's try and get up there and see if we can. This window is only six-course high. So it's going to be a funny... It probably would end up a tiny little slither. With a bit of luck, we'll get all the brickwork up and maybe get it backed up. And then tomorrow, we need to get the trest set up through here. So I can get up with the saw and cut a pocket out each end to get the wall in. And our inspector also wants the cavity cutting out, so I'm going to have to cut the six-inch cavity up there as well. But that won't be a problem with that rascal. I think it's about 100mm. I'm sure it's a 130mm depth cut. Sales for everything. I'll get you set up again. And we'll get there as these bricks was done. That's why I need to get my blocks sorted out. On the next course, I'm going to get the blocks done so we can get the lintel on and we can carry on. I'm going to have to... I don't know what to do with the cavity tray because we can't put an upstand on it. So if it was on this course, we'd get the upstand here because it's going to be a full brick on the end. The only place for an upstand is there, but the lintel is going to come through. So we'll just have to work around it and see what we can do with it. So yeah, let's get back up somewhere. Just like old times, when we did a video for Keystone, yeah, we did make a video for Keystone. I'll have to put a lintel in. I'm going to put this front lintel in, which is a bit of overhead height. That's where it's wanted. This is three courses below. The main lintel height is going to be on the door. So it's a nine under the lintel. There's a six in the cavity. There's K-150, 900, smallest you can get. Just about fit. What's that called? There's a cold bridge. That's a special name. Yeah. Yeah. That metal isn't attached to that metal except for these few little welds. So you've given it the cold bridge from the metal to metal. Now you're getting them now where they do where they place all together. I saw plastic ones at the trade show. Plastic tops there. Just about work. So this is a half on the end here. So I'll trail up this half. And then we've got a four brick on the other end. It works there. So the trail come up there. So it does actually work perfect for us. And then once we've gone over the top of this, of course we've just gone off to get some 18 inch damp. We've got a 300 there. It's not quite big enough because it's a big cavity. We need it wider stuff to get over a good cavity. Yeah. So yeah, get this leveled up. Three courses across the top. I mean it's this lintel, which obviously needs busting into there. So yeah, let's crack on. Insulation, aren't we? That is lintel height. Second lintel height. So this lintel is going to overlap. This lintel. It's a weird detail, but it's because it's a small window for the toilet. Just going to speak to the customer. So that wall plate height, et cetera. And you want an eight foot ceiling. So there's going to be 300 above there. I think it's going to be a course of block from lintel. And a four to three wall plate bedded up high. So get us to about four courses up, course above that right. And then I think it's going to be minimum two, maybe three on the outside. So another two, definitely maybe three on top of that. Plus all the block work obviously. And then the wall plate, which is coming tomorrow. So there's still plenty to work to do on this yet. There's all the extra to go up there yet. The extra three. That course to finish off. Lintels to break out. Cavities to cut out of the wall because the inspector wants the cavity continuous. So there's no cold bridge. I hope you're picking this up with the wind. Then obviously the pikes, which we can't work out. So we've got a wall plate height. I've got a bit of insulation left over, maybe a couple of packs. Still sealed. They can go back and get a refund on them. It's going to be using the eight before sheets of somewhere else on the job instead of taking that back. I think they wouldn't take it back now. It's a bit of a bit of site damage. So you can reuse that elsewhere. Works out roughly. Same price for a sheet of insulation. The 100 mil as it is for the, the dry firm cavity slabs. Four pair pack. Yeah. I'm going to join it up. The arch is tidying up. Yeah, that's us. Spot board's clean. Load out for tomorrow or maybe load out tomorrow. We'll see. We've got to do an outro again. Didn't we? Yeah. So we did make some good progress at least. But that's the end of the video. So thank you all very much for watching. If you enjoyed, be sure to give a thumbs up. And if you're new to the channel, you want to see more, hit subscribe and tap on that bell. It's meant to be a bell. That way you'll always know when we upload, which is a massive help and a good way to support the channel. And if you want to support the channel any extra ways, you can do the super thanks option under the video or there's a link to Dad's PayPal. Not necessary, but appreciated nonetheless. Every little bit towards Dad's trust fund for his hip. We've got some very kind donations. Yeah, so everybody who's been donating very much appreciated. Thank you. So this has been lounging about and I'll live in room with Stephen Alex. And we'll see you in the next one.